NECメーカーPA242Wの使用説明書/サービス説明書
ページ先へ移動 of 39
MultiSync P A242W MultiSync P A272W MultiSync P A302W User ’ s Manual.
Inde x W arning, Caution .......................................................................................................................... English-1 Registration Information ....................................................................
English-1 English W ARNING CA UTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER T O THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET .DO NOT REMOVE COVER (OR BACK).
English-2 Registration Inf ormation FCC Inf ormation 1. Use the attached specifi ed cables with the MultiSync P A242W/MultiSync P A272W/MultiSync P A302W monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.
English-3 English Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NO T OPEN THE MONIT OR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English-5 English Pr oduct Features • DisplayPort and HDMI, which support 10-bit color depth. • 5-setting, easy-to-switch picture mode (see page 13). • Accurate color reproduction for high-end graphic design (see page 17). • Quick warmup time.
English-6 Quic k Star t T o connect the LCD monitor to your system, follow these instructions: NO TE: Make sure to read “Recommended Use” (page 3) before installation. In order to display the maximum resolution, a video card that can output a resolution of 2560 x 1440 (P A272W) or 2560 x 1600 (P A302W) is needed.
English-7 English 4. Connect all cables to the appropriate connectors ( Figure C.1 ). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer ( Figure C.
English-8 7. Slide down the cable cover ( Figure D .1 ). 8. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet. NO TE: Please refer to Caution section of this manual for proper selection of AC power cord.
English-9 English Screen Rotation Before rotating, the screen must be raised to the highest level and tilt to avoid knocking the screen on the desk or pinching your fi ngers. Disconnect all cables. T o raise the screen, place hands on each side of the monitor and lift up to the highest position ( Figure RL.
English-10 Figure S.1 Flexib le Arm Installation This LCD monitor is designed for use with a fl exible arm. T o prepare the monitor for alternate mounting purposes: NO TE: For P A302W , the monitor must be installed or moved by two or more people. • Follow the instructions provided by the manufacturer of the display mount.
English-11 English Contr ols OSD (On-Screen Displa y) control b uttons on the front of the monitor function as f ollows: T o access OSD menu, press the MENU button. T o change signal input, press the SELECT button. NO TE: OSD must be closed in order to change signal input.
English-12 Brightness/Contrast Contr ols BRIGHTNESS Adjusts the overall image and background screen brightness. NO TE: The brightness level is adjusted using the backlight output. The display will digitally compensate for low or high brightness levels.
English-13 English FINE (Analog input only)* Improves focus, clarity and image stability by increasing or decreasing this setting. If the “AUTO ADJUST” function and the “H.SIZE” function do not give you a satisfactory picture setting, a fi ne tuning can be performed using the “FINE” function.
English-14 T ools PIP MODE Select PIP MODE, OFF/PIP/PICTURE BY PICTURE - ASPECT/PICTURE BY PICTURE - FULL. Y ou can select individual PICTURE MODE in each screen.
English-15 English OFF MODE The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of inactivity . The OFF MODE has four settings. OFF: Monitor does not go into power save mode when the input signal is lost. ST ANDARD: Monitor enters power save mode automatically when the input signal is lost.
English-16 F A CT OR Y PRESET Selecting F ACTORY PRESET allows you to reset all OSD control settings (BRIGHTNESS, CONTRAST* 1 , ECOMODE, BLACK, IMAGE CONTROL, COLOR CONTROL SYSTEM, SHARPNESS, PIP MODE.
English-17 English Using the PICTURE MODE function Choose the Picture Mode that is most suitable for the type of content that is shown. There are several types of mode (sRGB, Adobe ® RGB, DCI, REC-Bt709, HIGH BRIGHT , FULL, DICOM, PROGRAMMABLE).
English-18 Ad v anced OSD If you need detailed information about the controls, please use the advanced menu. There are 2 ways to access the advanced menu. Method 1: <T o access the advanced menu> • Press the Menu button to access OSD menu. Use the front buttons to move the cursor to the ADV ANCED SETTING in Color control systems.
English-19 English GAMMA Allows you to manually select the brightness level of grayscale. There are fi ve selections: sRGB, L Star , DICOM, PROGRAMMABLE and CUSTOM. We recommend to show a grayscale image on screen while adjusting gamma. sRGB: GAMMA setting for sRGB.
English-20 UNIFORMITY This function electronically compensates for the slight variations in the white uniformity level as well as for deviations in color that may occur throughout the display area of the screen. These variations are characteristic of LCD panel technology .
English-21 English DIGIT AL LONG CABLE (DVI/HDMI input only) Compensates for image degradation caused by using a long cable. A lower number produces less compensation. DIGIT AL LONG CABLE (DP/Mini-DP* 1 input only) Compensates for disturbed image caused by using a long DisplayPort cable.
English-22 H.SIZE* (Analog input only) Adjusts the horizontal size of the screen. If the “AUTO ADJUST” function do not give you a satisfactory picture setting, a further tuning can be performed using the “H.SIZE (V .SIZE)” function (dot clock).
English-23 English POWER SA VE TIMER ON: Monitor automatically changes to OFF mode after 2 hours of continuous no-video signal. OFF: Monitor will not automatically change to OFF mode when no video signal is connected. OFF MODE The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of inactivity .
English-24 HOT KEY* 2 When this function is activated; the brightness of the monitor can be adjusted without entering the OSD menu by using the front buttons. The “LEFT” or “RIGHT” buttons adjust the brightness level. When this function is set to OFF , some buttons are disabled.
English-25 English * Only for P A302W . * 2 This item does not reset by FACT ORY PRESET (T ag7). T agA TILE MA TRIX The TILE MA TRIX feature allows one image to be displayed over multiple screens. This feature can be used with up to 25 monitors (5 vertical and 5 horizontal).
English-26 Specifi cations - P A242W Monitor Specifi cations MultiSync P A242W Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 61.1 cm/24.1 inches 61.1 cm/24.1 inches 1920 x 1200 Active matrix; thin fi lm transistor (TFT) liquid crystal display (LCD); 0.
English-27 English Specifi cations - P A272W Monitor Specifi cations MultiSync P A272W Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 68.5 cm/27.0 inches 68.5 cm/27.0 inches 2560 x 1440 Active matrix; thin fi lm transistor (TFT) liquid crystal display (LCD); 0.
English-28 Specifi cations - P A302W Monitor Specifi cations MultiSync P A302W Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 75.6 cm/29.8 inches 75.6 cm/29.8 inches 2560 x 1600 Active matrix; thin fi lm transistor (TFT) liquid crystal display (LCD); 0.
English-29 English Features DisplayP or t: DisplayPort is designed to be the future-ready , scalable solution for high performance digital display connectivity . It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables.
English-30 T roub leshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • The monitor does not support a DisplayPort converter signal. • The front power button and computer power switch should be in the ON position.
English-31 English Picture is not as bright • Make sure ECO MODE and AUTO BRIGHTNESS are turned off. • If the brightness fl uctuates make sure AUTO BRIGHTNESS is turned of f. • In PICTURE MODE, set HIGH BRIGHT . See page 17. • LCD brightness degradation occurs due to long-term usage or extreme cold conditions.
English-32 Using the A uto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly .
English-33 English Self Calibration (P A302W onl y) Simply connect the external USB color sensor , and re-calibrate the factory settings without the need of a computer . This feature is to compensate for a yellow color shift that typically occurs with long-term LCD usage.
English-34 6. The procedure will ask for the USB color sensor to be placed on the center of the display panel ( Figure S.3 ). Tilt the display panel approximately 5˚ backward and place the USB color sensor in the center of the display panel ( Figure S.
English-35 English White P oint Matching/Cop y (P A302W onl y) The white point can be copied from one display to one or more additional displays. Using this feature reduces the variation between different displays allowing them to match each other more closely .
English-36 8. Press SELECT to start the confi rmation of white point. 9. After the confi rmation is fi nished, FINE TUNING MODE message appears. 10.
English-37 English NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment.
デバイスNEC PA242Wの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC PA242Wをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC PA242Wの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC PA242Wの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC PA242Wで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC PA242Wを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC PA242Wの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC PA242Wに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC PA242Wデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。