Net OpticsメーカーPAD-CU-ARの使用説明書/サービス説明書
ページ先へ移動 of 20
Installation Guide for 10/100BaseT Port Aggregator T ap with Active Response Models P A-CU-AR, P AD-CU-AR Doc. PUBP ACUARU Rev . 1, 06/06.
.
10/100 Port Aggregator T ap Contents I n t r o d u c t i o n .....................................................1 Key Features ....................................................3 Unpacking and Inspection ..........................................4 Product Diagrams .
10/100 Port Aggregator T ap PLEASE READ THESE LEGAL NOTICES CAREFULL Y . By using a Net Optics T ap you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual.
10/100 Port Aggregator T ap 1 Introduction Net Optics 10/100 Dual Port Aggregator T aps with Active Response provide ultra-efcient access to critical links with the option to inject an active re - sponse into the network.
10/100 Port Aggregator T ap 2 Simple to Deploy Net Optics’ Dual Port Aggregator T ap with Active Response is a simple plug- and-play solution addressing the fact that many monitoring systems, including most software based solutions, only offer a single channel NIC, limiting full- duplex visibility .
10/100 Port Aggregator T ap 3 K ey Fea tur es Passive, Secure T echnology Supports full-duplex monitoring with a single NIC, increasing monitoring efciency Regeneration T ap technology enables two .
10/100 Port Aggregator T ap 4 Unpacking and Inspection Carefully unpack the 10/100 Port Aggregator T ap w/Active Response and check for damaged or missing parts.
10/100 Port Aggregator T ap 5 Figure 3: Rear Panel LED Indicators PWR 1/ PWR 2: Main and Redundant Power . If the T ap is deployed with both power supplies, both LEDs will illuminate when the T ap is plugged in. If an LED is off, this indicates that the corresponding power supply is not functioning.
10/100 Port Aggregator T ap 6 Each using a single NIC, the monitoring devices both receive all combined traffic from Side A and Side B, including physical layer errors. State 1: Side A + Side B is less than or equal to 100% of the NIC's receive capacity.
10/100 Port Aggregator T ap 7 The Tap applies a first-in, first-out process to all packets. Once the burst has ended and the NIC's utilization is again below 100 percent, the Tap first processes the packets that were stored in memory.
10/100 Port Aggregator T ap 8 Cabling Guidelines Use straight-through cable to connect the T ap Ports to a Router or NIC. Use cross-over cable to connect the T ap Ports to Switches and Hubs. The T ap Ports T ransmit on Pins 3 & 6 and Receive on Pins 1 & 2.
10/100 Port Aggregator T ap 9 Connecting to the Monitoring De vice(s) 1. Supply power to the T ap using the power supplies included with the unit. T wo power supplies are included.
10/100 Port Aggregator T ap 10 DIP Switch Settings Switch Function Description 1 T urns Auto-negotiation ON or OFF . Factory default setting is Auto-negotiation. If turned ON, ports A, B, and C/D automatically negotiate the links. Positions 2 thru 8 are inac- tive.
10/100 Port Aggregator T ap 1 1 Activ e Response T ap F AQs Q: What types of active r esponses are supported? A: W ith an Active Response Dual Port Aggregator T ap, an administrator can transmit any t.
10/100 Port Aggregator T ap 12 Activ e Response T ap F AQs (Continued) Q: How much bandwidth is available on the Active Response Port? A: The average amount of bandwidth for active responses is determined by the average available capacity on the link.
10/100 Port Aggregator T ap 13 Specications Environment Operating T emperature: 0˚C to 55˚C Storage T emperature: -10˚C to 70˚C Relative Humidity: 10% min, 95% max, non-condensing Power Power Supply Input: 100-240V AC, 0.5A, 47-63Hz Output: 12V , 1.
10/100 Port Aggregator T ap 14 Limitations on W ar ranty and Lia bility Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC.
.
© 2007 by Net Optics, Inc. All Rights Reserved. www .netoptics.com.
デバイスNet Optics PAD-CU-ARの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Net Optics PAD-CU-ARをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNet Optics PAD-CU-ARの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Net Optics PAD-CU-ARの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Net Optics PAD-CU-ARで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Net Optics PAD-CU-ARを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNet Optics PAD-CU-ARの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Net Optics PAD-CU-ARに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNet Optics PAD-CU-ARデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
