NetCommメーカーNS4540の使用説明書/サービス説明書
ページ先へ移動 of 58
NS4540 Your Eye Online, All the time..
NetComm NS4540 Dome Camera User Guide YML7** Rev1 2 www.netcomm.com.au Contents WARNING & CAUTION .............................................................................................................. ... 4 1. Introduction ................
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 3 6-2 Network Setting ............................................................................................................ 3 7 6-2-1 Network General Settings ................
NetComm NS4540 Dome Camera User Guide YML7** Rev1 4 www.netcomm.com.au WARNING & CAUTION WARNING & CAUTION WARNING & CAUTION WARNING & CAUTION WARNING & CAUTION Please read the manual before attempting installation or operation Please be aware of the following: 1 .
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 5 1. 1. 1. 1. 1. Introduction Introduction Introduction Introduction Introduction 1-1 What is the NETCOMM Network Dome Camera? ■ .
NetComm NS4540 Dome Camera User Guide YML7** Rev1 6 www.netcomm.com.au 1-2 Advantage Features ■ 22X Auto Focus Lens (NETCOMM -261) ■ Built-in 22X optical zoom lens with focal length 3.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 7 1-3 Package Contents.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 8 www.netcomm.com.au 2. 2. 2. 2. 2. Hardware Hardware Hardware Hardware Hardware 2-1 Structural Elements 1. Dome Cover 2. Camera Case 3. Decoration Ring 4. RS-485 In/Out Jack 5. Alarm In / Out Jack 6. Video In / Out Jack 7.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 9 2-2 Connection Jack and Cable Requirement ■ Power In Jack : DC12V Input V oltage, Power Consumption 1.2Adc, Center Pin 2.0mm Requires Cable: 18 A WG x 2C ■ V ideo Out BNC Jack : V ideo Signal Output CVBS 1.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 10 www.netcomm.com.au ■ Ethernet: Standard IEEE802.3 10 Base T port ■ POWER/ST A TUS LED: Power On: constant red. - Emergency factory default (appendix C): Blinking orange (i.e. red mix with green).
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 11 2-3 DIP Switch Setting ■ Fan Power Switch T urn the number 2 switch to ON position to activate the internal fan. This will maintain the temperature inside. ■ Alarm Mode Switch Alarm Mode can be set as Lock or Release mode.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 12 www.netcomm.com.au 2-4 NETCOMM NS4540 ID Address Setting Refer Chart Up to 64 NETCOMM NS4540 can be serially linked in one system. Therefore each dome is addressed by ID switch located at the base of the NETCOMM NS4540.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 13 3. 3. 3. 3. 3. Installation Installation Installation Installation Installation 3-1 Indoor Installation Structural Drawing.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 14 www.netcomm.com.au 3-2 Outdoor Installation Structural Drawing (Pendant Mounting).
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 15 3-3 Embedded Mounting (False Ceiling) Note: After dome cover is attached, use glass-cleaning cloth to clean dome cover.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 16 www.netcomm.com.au.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 17.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 18 www.netcomm.com.au 3-4 Attached Mounting (Fixed Ceiling).
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 19.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 20 www.netcomm.com.au.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 21.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 22 www.netcomm.com.au.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 23 3-5 Pendant Mounting (External Housing) Note: When NETCOMM NS4540 is installed inside outdoor housing, please don't attach dome cover; doing so may affect camera performance.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 24 www.netcomm.com.au.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 25 4. 4. 4. 4. 4. Configuring your Camera Configuring your Camera Configuring your Camera Configuring your Camera Configuring your Camera 4-1 Preparation before IP Assignment: Always consult your network administrator before assigning an IP address from your server .
NetComm NS4540 Dome Camera User Guide YML7** Rev1 26 www.netcomm.com.au 3 . Enter command <arp -s [NETCOMM NS4540 IP Address] [NETCOMM NS4540 MAC Address] ■ In DOS, enter "arp -s 192.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 27 4-3 Assign IP by IP Installer NETCOMM IP Installer is a W indows 98/ME/NT/2000 program. It is the software application that proves an easier way for the setting of IP address and network configuration of NETCOMM 's NDC.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 28 www.netcomm.com.au 4-3-3 Assign an IP Address to NETCOMM NS4540 Select the MAC Address of your NETCOMM NS4540 in the list. The MAC Address is identical to the unit's S/N (Serial Number). And click the menu bar V iew/Property to open the Property Page for the selected item.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 29 4-4 Verify the IP Address and Open the Home Page T o access the Home Page of the selected unit, run the V iew/Open W eb on the menu bar .
NetComm NS4540 Dome Camera User Guide YML7** Rev1 30 www.netcomm.com.au The NETCOMM NS4540 can support Microsoft Internet Explorer and Netscape. But the voice feature can only be run under Microsoft Internet Explorer .
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 31 5. 5. 5. 5. 5. NETCOMM NS4540 Homepages' Usage Overview NETCOMM NS4540 Homepages' Usage Overview NETCOMM NS4540 Homepa.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 32 www.netcomm.com.au 5-2 Configuration Page The Configurations of the NETCOMM NS4540 are now presented as links in the margin of the Configuration Page. Simply click the relevant link for the settings you want to configure.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 33 I/O Configurations Functions Description GPIO General Purpose Input / Output. These are for event triggers and actions PTZ Device T o control the PTZ device and set the preset points.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 34 www.netcomm.com.au 6. 6. 6. 6. 6. NETCOMM NS4540 Configurations Setting NETCOMM NS4540 Configurations Setting NETCOMM NS4540 Configurations Setting NETCOMM NS4540 Configurations Setting NETCOMM NS4540 Configurations Setting 6-1.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 35 ■ "Restricted User" is the user in User Configuration without administration permission. The user can be configured to have limited permission to see video, for example, "capable of changing video size, etc".
NetComm NS4540 Dome Camera User Guide YML7** Rev1 36 www.netcomm.com.au 6-1-3 Clock Setting The built-in real-time clock of NETCOMM NS4540 provides accurate date/time for the system even when the power is of f.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 37 6-2 Network Setting 6-2-1 Network General Settings IP Addr ess: NETCOMM NS4540 IP address Subnet Mask: Subnet mask of your LAN. Note that the IP Address above and Gateway IP Address below should be in the same subnet.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 38 www.netcomm.com.au 6-2-2 SMTP Settings Sender's Email Addr ess: Y our E-mail address. SMTP Server Address: SMTP server IP address. Authentication: If the SMTP Server has enabled authentication function.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 39 Upload Path: Path to put the file. IP Notification by E-mail: W ith this option enabled, your NETCOMM NS4540 will send E- mail to you as soon as it obtains the IP address from the DHCP server .
NetComm NS4540 Dome Camera User Guide YML7** Rev1 40 www.netcomm.com.au Note: The NETCOMM DDNS service is proprietary, which only works with NETCOMM DDNS server and NETCOMM brands o f products. Dynamic DNS Activate: Click on to activate NETCOMM DDNS service.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 41 6-3 I / O Configuration 6-3-1 GPIO Input Status Display the GPIO (General Purpose Input) status. The GPIO T erminal Block / MINI DIN provide control signal input, which includes four GPIO inputs as Relay function.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 42 www.netcomm.com.au 6-4 Video Setting 6-4-1 Time Stamp Display T ime S tamp & T ext over the video just click on these check boxes. Display T ime check box: Display the T ime Stamp. Display T ext check box: Display text block.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 43 6-4-2 Video Adjustment The NETCOMM NS4540 is capable of detecting NTSC/P AL automatically , video signal active/ lose, fully automatic (plug & see) and does not need any user configuration.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 44 www.netcomm.com.au 6-5 Event Management 6-5-1 Motion Area Selection Motion Detection Region Selection: Move the mouse to the regions in video window with white blocks to determine the motion trigger areas.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 45 6-5-2 Event Edit Application developers wish to have different levels of customization within their own applications.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 46 www.netcomm.com.au Save Script: Command to save and parse current scripts in the "Event Script Edit" window . If any syntax errors are detected, the error message, indicating the starting position of syntax error , will be shown in the "Message" window .
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 47 Appendix A - Specifications Appendix A - Specifications Appendix A - Specifications Appendix A - Specifications Appendix A - Specifications Operational Manual Pan/ T ilt Speed 0.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 48 www.netcomm.com.au White Balance .17X / 22X : Auto / Outdoor / Indoor 25X : 2 Auto mode / Outdoor / Indoor V ideo Output CVBS 1.0Vpp 75? Optical Lens 22X Lens Focal Length f = 3.9~86mm 22X Lens Aperture Max F1.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 49 Appendix B - Upgrading the Software Appendix B - Upgrading the Software Appendix B - Upgrading the Software Appendix B - Upgradi.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 50 www.netcomm.com.au 5 . Upload the software into NETCOMM NS4540 by FTP "put" command. In FTP session window , enter "put flash.bin" In FTP session window , enter "bye" to quit FTP session.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 51 Appendix C - Update custom web pages Appendix C - Update custom web pages Appendix C - Update custom web pages Appendix C - Upda.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 52 www.netcomm.com.au 4) Verify updated contents After uploading the custom pages, open browser to verify the correctness of contents. If not correct, modify the pages and return to previous step to upload again.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 53 Appendix D - Emergency Factory Default Appendix D - Emergency Factory Default Appendix D - Emergency Factory Default Appendix D .
NetComm NS4540 Dome Camera User Guide YML7** Rev1 54 www.netcomm.com.au Appendix E - Trouble Shooting Appendix E - Trouble Shooting Appendix E - Trouble Shooting Appendix E - Trouble Shooting Appendix E - Trouble Shooting T rouble Shooting 1 No Power 1 .
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 55 Appendix F - Registering your NetComm Product Appendix F - Registering your NetComm Product Appendix F - Registering your NetCom.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 56 www.netcomm.com.au Customer Information ACA (Australian Communications Authority) requires you to be aware of the following information and warning.
YML7** Rev1 NetComm NS4540 Dome Camera User Guide www.netcomm.com.au 57 Warranty Where the Customer (you) is a consumer as defined by any relevant law such as the T rade Practices Act 1974 (Commonwealth) and similar State laws, certain conditions and warranties (“the consumer warranties”) cannot be excluded, restricted or modified.
NetComm NS4540 Dome Camera User Guide YML7** Rev1 58 www.netcomm.com.au The warranty is void if: 1 . Y ou, or someone else, use the product, or attempt to use it, other than as specified by NetComm; 2 .
デバイスNetComm NS4540の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NetComm NS4540をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNetComm NS4540の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NetComm NS4540の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NetComm NS4540で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NetComm NS4540を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNetComm NS4540の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NetComm NS4540に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNetComm NS4540デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。