NETGEARメーカーDGND3300-100NASの使用説明書/サービス説明書
ページ先へ移動 of 177
350 East Plumeria Drive San Jose, CA 95134 USA October 2010 202-10463-04 v1.0 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual.
2 | N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual ©2010 NETGEAR, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc.
Contents | 3 Table of Contents Chapter 1 Router Internet Setup Using the Setup Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Logging In to Your N300 Wireless Modem Router . . . . . . . . . . . . . . . . . . .
4 | Contents N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Setting the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Chapter 4 Network Maintenance Upgrading the Firmware . . . . .
Contents | 5 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Activating a VPN Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Verifying the Status of a VPN Tunnel . . . . . . . . . . . . . . . . .
6 | Contents N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Appendix B Default Configuration and Technical Specifications Restoring the Factory Configuration Settings . . . . . . . . . . . . . . . . . . . . . . 147 Using the Restore Factory Settings Button .
Chapter 1. Router Internet Setup | 7 1 1. Router Internet Setup Connecting to the network This chapter describes how to configure your N300 Wireless Modem Router Internet connection.
8 | Chapter 1. Router Internet Setup N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Logging In to Your N300 Wireless Modem Router You can log in to the N300 wireless modem router to view or change its settings. Links to the Knowledge Base and documentation are also available on the N300 wireless modem router main menu.
Chapter 1. Router Internet Setup | 9 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 2. Note: If the N300 wireless modem router is not configured (is in its factory default state) when you log in, the Setup Wizard displays. See Using the Setup Wizard on page 9.
10 | Chapter 1. Router Internet Setup N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 4. 2. Under Auto-Detect Connection Type, select Yes and then click Next to proceed. 3. Enter your ISP settings, as needed. 4. At the end of the Setup Wizard, click Test to verify your Internet connection.
Chapter 1. Router Internet Setup | 11 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 5. 3. Select Yes or No depending on whether your ISP requires a login. This selection changes the fields available on the Basic Settings screen.
12 | Chapter 1. Router Internet Setup N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 6. Settings Description Does Your ISP Require a Login? • Yes • No These fields appear only if no login is required. Account Name (If required) Enter the account name provided by your ISP.
Chapter 1. Router Internet Setup | 13 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Internet IP Address • Get Dynamically from ISP . Your ISP uses DHCP to assign your IP address. Your ISP automatically assigns these addresses. • Use Static IP Address .
14 | Chapter 1. Router Internet Setup N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Configuring ADSL Settings Note: For information about how to install ADSL filters, see the Setup Manual . NETGEAR recommends that you use the Setup Wizard to automatically detect and configure your ADSL settings.
Chapter 2. Wireless Settings | 15 2 2. Wireless Settings Protecting your network For a wireless connection, the SSID, also called the wireless network name, and the wireless security setting must be the same for the N300 wireless modem router and wireless computers or wireless adapters.
16 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual - SSID. The default 11N SSID for the N300 wireless modem router is NETGEAR-DualBand-N. The default 11G SSID is NETGEAR-2.4-G. - The wireless mode (802.
Chapter 2. Wireless Settings | 17 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • Put the antenna in a vertical position to provide the best side-to-side coverage. Put the antenna in a horizontal position to provide the best up-and-down coverage.
18 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: NETGEAR recommends WPA2 security because it is the strongest, and WPA security as the next strongest.
Chapter 2. Wireless Settings | 19 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 9. The settings for this screen are explained in the following table. Settings Description Name (11N SSID) Name (11G SSID) This is the wireless network name.
20 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 3. Select the region in which the N300 wireless modem router will operate. 4. For initial configuration and test, leave the other settings unchanged. 5.
Chapter 2. Wireless Settings | 21 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: NETGEAR recommends WPA2 security because it is the strongest, and WPA security as the next strongest.
22 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 6. Enter the encryption keys. You can manually or automatically program the four data encryption keys. These values must be identical on all computers and access points in your network: • Passphrase .
Chapter 2. Wireless Settings | 23 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To configure WPA or WPA2 in the N300 wireless modem router: 1. Log in to the N300 wireless modem router at its default LAN address of http ://192.168.
24 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Using Push 'N' Connect (WPS) to Configure Your Wireless Network If your wireless clients .
Chapter 2. Wireless Settings | 25 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual and default password of password , or using whatever LAN address and password you have set up. 2. On the N300 wireless modem router main menu, select Add WPS Client , and then click Next .
26 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The first time you add a WPS client, make sure that the Keep Existing Wireless Settings check box on the WPS Settings screen is cleared.
Chapter 2. Wireless Settings | 27 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Configuring Advanced WPS Settings From the main menu, select Advanced > Wireless Settings to display the following screen: Figure 14.
28 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Adding More WPS Clients Note: Your wireless settings remain the same when you add another WPS-enabl.
Chapter 2. Wireless Settings | 29 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: To make sure that your new wireless settings remain in effect, verify that the Keep Existing Wireless Settings check box is selected in the WPS Settings screen.
30 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: The SSID of any wireless access adapters must match the SSID you configure in the N300 wireless modem router. If they do not match, you will not get a wireless connection to the N300 wireless modem router.
Chapter 2. Wireless Settings | 31 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To configure a wireless guest network: 1. In the main menu, under Setup, select either Wireless Guest Network g/b or Wireless Guest Network a, n . A Wireless Guest Network Settings screen similar to the following figure displays: Figure 16.
32 | Chapter 2. Wireless Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Enter a value of up to 32 alphanumeric characters. For the selected guest network, the same name must be assigned to all wireless devices in your network.
Chapter 2. Wireless Settings | 33 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Flexible Settings You might have your own computer or you might be sharing a computer with other members in the family.
Chapter 3. Security Settings | 34 3 3. Security Settings Keeping unwanted content out of your network This chapter describes how to use the content filtering and reporting features of the N300 wireless modem router to protect your network.
Chapter 3. Security Settings | 35 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual NETGEAR recommends that you change this password to a more secure password. The ideal password should contain no dictionary words from any language, and should be a mixture of both uppercase and lowercase letters, numbers, and symbols.
36 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 2. From the main menu, under Advanced > Wireless Settings , and then click Setup Access List to display the Wireless Card Access List screen. Figure 17.
Chapter 3. Security Settings | 37 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual - If the wireless station is shown in the Available Wireless Stations list, click its radio button to select it, and then click Add .
38 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To block by schedule, be sure to specify a time period in the Schedule screen. For information about scheduling, see Scheduling Blocking on page 45. Block all access to Internet browsing during a scheduled period by entering a dot ( .
Chapter 3. Security Settings | 39 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 20. • Outbound Services . This lists all existing rules for outbound traffic. If you have not defined any rules, only the default rule is listed.
40 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 21. 2. From the Service list, select the service that you want to add or edit. 3. Enter the settings to specify the service as explained in the following table.
Chapter 3. Security Settings | 41 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 4. Click Apply to have your changes take effect. The new rule will be listed in the table when you return to the Firewall Rules screen.
42 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual You can add a pre-set port forwarding rule or a custom rule. Adding a Pre-set Port Forwarding Rule 1. From the Port Forwarding screen, click Add to display the following screen: Figure 23.
Chapter 3. Security Settings | 43 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 7. Click Apply . The service appears in the list. Port Triggering Port triggering is an advanced feature that can be used to easily enable gaming and other Internet applications that would otherwise be blocked by the firewall.
44 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 25. 2. Specify the information for port triggering: • Service Name . Enter a name for the rule, up to 30 characters. • Service User . The PC on the LAN that can use the port triggering rule to create a dynamic inbound mapping to it.
Chapter 3. Security Settings | 45 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To block access to Internet services: 1. From the main menu, select Security > Services . The Services screen displays. Figure 26. 2. To add a service, click Add Custom Service .
46 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 28. 2. Configure the schedule for blocking keywords and services. a. Days . Select days on which you want to apply blocking by selecting the appropriate check boxes.
Chapter 3. Security Settings | 47 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 29. The following information is provided in the logs: Configuring Email Alert and Web Access Log Notifications To receive logs and alerts by e-mail, you must provide your e-mail account information.
48 | Chapter 3. Security Settings N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 30. 2. To receive email logs and alerts from the N300 wireless modem router, select the Turn E-mail Notification On check box.
Chapter 3. Security Settings | 49 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 5. Click Apply to save your settings. So that the log entries are correctly time-stamped and sent at the correct time, be sure to set the time as described in the next section.
Chapter 4. Network Maintenance | 50 4 4. Network Maintenance Administering your network This chapter describes features to help you manage your N300 wireless modem router.
Chapter 4. Network Maintenance | 51 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: To turn off the automatic firmware check at login, clear the Check for Updated Firmware Upon Log-in check box on the Router Upgrade screen.
52 | Chapter 4. Network Maintenance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 3. If the firmware version on the NETGEAR website is newer than the firmware on your N300 wireless modem router, download the file to your computer.
Chapter 4. Network Maintenance | 53 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 34. You can use the Show Statics and Connection Status buttons to view additional status information, as described in Connection Status on page 55 and Statistics on page 56.
54 | Chapter 4. Network Maintenance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Internet Port MAC Address The Media Access Control address. This is the unique physical address being used by the Internet (WAN) port of the N300 wireless modem router.
Chapter 4. Network Maintenance | 55 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Connection Status To view the connection status, on the Router Status screen, click Connection Status . Figure 35. • Click the Connect button, and the N300 wireless modem router attempts to connect to the Internet.
56 | Chapter 4. Network Maintenance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Statistics To view statistics, on the Router Status screen, click Show Statistics . Figure 36. The following table describes the N300 wireless modem router statistics.
Chapter 4. Network Maintenance | 57 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Viewing a List of Attached Devices The Attached Devices table lists all IP devices that the N300 wireless modem router has discovered on the local network.
58 | Chapter 4. Network Maintenance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Backing Up and Restoring the Configuration The Restore and Backup options in the Backup Settings screen let you save and retrieve a file containing your N300 wireless modem router’s configuration settings.
Chapter 4. Network Maintenance | 59 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 39. You can use the Diagnostics screen to perform the following functions from the N300 wireless modem router: • Ping an IP address to test connectivity to see if you can reach a remote host.
60 | Chapter 4. Network Maintenance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 40. Note: Be sure to change the N300 wireless modem router’s default configuration password to a very secure password.
Chapter 4. Network Maintenance | 61 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • To allow access from a single IP address on the Internet, select Only This Computer . Enter the IP address that will be allowed access. 3. Specify the port number for accessing the management interface.
62 | Chapter 4. Network Maintenance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 41. a. To enable the traffic meter, select the Enable Traffic Meter check box. 2. If you would like to record and restrict the volume of Internet traffic, select the Traffic volume control by radio button.
Chapter 4. Network Maintenance | 63 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • The Internet connection is disconnected and disabled. 6. Under Internet Traffic Statistics, set up monitoring the data traffic. 7. Click the Traffic Status button if you want a live update on Internet traffic status on your router.
Chapter 5. USB Storage | 64 5 5. USB Storage Network storage for sharing files and backing up data This chapter describes how to access and configure a USB storage drive attached to your N300 wireless modem router.
Chapter 5. USB Storage | 65 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual USB Drive Requirements The N300 wireless modem router works with 1.0 and 1.1 (USB Full Speed) and 2.0 (USB High Speed) standards. The approximate USB bus speeds are shown in the following table.
66 | Chapter 5. USB Storage N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Sharing Photos with Friends and Family You can create your own central storage location for photos and multimedia. This eliminates the need to log in to (and pay for) an external photo sharing site.
Chapter 5. USB Storage | 67 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: The password for admin is the same one that you use to access the N300 wireless modem router. By default it is password . 3. Enable FTP through the Internet in the USB Storage (Advanced Settings) screen.
68 | Chapter 5. USB Storage N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: If you logged in to the N300 wireless modem router before you connected your USB device, you might not see your USB device in the N300 wireless modem router screens until you log out and then log back in again.
Chapter 5. USB Storage | 69 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 45. You can use this screen to select a folder, to change the share name, or t o change the read access or write access from All - no password to admin .
70 | Chapter 5. USB Storage N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 46. You can use this screen to specify access to the USB storage device. The following table explains the fields and buttons in the USB Storage (Advanced Settings) screen.
Chapter 5. USB Storage | 71 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Creating a Network Folder From the USB Storage (Advanced Settings) screen, click the Create a Network Folder button to open the Create Network Folder screen: Figure 47.
72 | Chapter 5. USB Storage N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Media Server Settings You can set this modem router as a ReadyDLNA media server to enable the playback of videos, movies, and pictures on DLNA/UPnP AV-compliant media players such as the Xbox360, Playstation, and NETGEAR’s Digital Entertainer Live.
Chapter 5. USB Storage | 73 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 1. From the main menu, select Advanced > USB Settings , and then click Approved Devices . The USB Drive Approved Settings screen displays: Figure 48. 2. Select the USB device from the Available USB Devices list.
74 | Chapter 5. USB Storage N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 3. Record the IP address that is listed for the Internet port. This is the IP address you can use to connect to the router remotely. Accessing the Router’s USB Drive Remotely Using FTP You can connect to the router’s USB drive using a Web browser: 1.
Chapter 5. USB Storage | 75 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: If you have any questions about File and Printer Sharing, contact Microsoft for assistance. Configuring Windows 2000 and Windows XP Right-click the network connection for your local area network.
Chapter 6. Virtual Private Networking | 76 6 6. Virtual Private Networking Setting up secure encrypted communications This chapter describes how to use the virtual private networking (VPN) features of the N300 wireless modem router. VPN communications paths are called tunnels.
Chapter 6. Virtual Private Networking | 77 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Client-to-Gateway VPN Tunnels Client-to-gateway VPN tunnels provide secure access from a remote PC, such as a telecommuter connecting to an office network.
78 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Planning a VPN When you set up a VPN, it is helpful to plan the network configuration and .
Chapter 6. Virtual Private Networking | 79 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual - The typical automated Internet Key Exchange (IKE) setup (see Using Auto Policy to Config.
80 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual configuration mismatches between your N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 and the corresponding VPN endpoint gateway or client workstation.
Chapter 6. Virtual Private Networking | 81 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To configure a client-to-gateway VPN tunnel using the VPN Wizard: 1. Log in to the N300 wireless modem router. On the main menu under Advanced - VPN, select VPN Wizard .
82 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 4. Select the radio button for the type of target end point, and click Next .
Chapter 6. Virtual Private Networking | 83 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 6. Click Done on the Summary screen. The VPN Policies screen displays, showing that the new tunnel is enabled: To view or modify the tunnel settings, select its radio button and click Edit .
84 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual a. Run the NETGEAR ProSafe Security Policy Editor program, and, using the Table 3 on page 80, create a VPN connection. b. From the Edit menu of the Security Policy Editor, select Add , and then click Connection .
Chapter 6. Virtual Private Networking | 85 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual g. Enter the public WAN IP address of the N300 wireless modem router in the field directly below the ID Type drop-down list. In this example, 22.
86 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual a. In the Network Security Policy list on the left side of the Security Policy Editor window, click My Identity . b. In the Select Certificate drop-down list, select None .
Chapter 6. Virtual Private Networking | 87 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual a. In the Network Security Policy list on the left side of the Security Policy Editor window, expand the Security Policy heading by double-clicking its name or clicking the + symbol.
88 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual a. Expand the Key Exchange subheading by double-clicking its name or clicking the + symbol. Then select Proposal 1 below Key Exchange. b. In the SA Life drop-down list, select Unspecified .
Chapter 6. Virtual Private Networking | 89 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual c. Type ping -t 192.168.3.1 , and then click OK . This causes a continuous ping to be sent to the first N300 wireless modem router. After between several seconds and 2 minutes, the ping response should change from timed out to reply .
90 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: Use the active VPN tunnel information and pings to determine whether a failed connection is due to the VPN tunnel or some reason outside the VPN tunnel.
Chapter 6. Virtual Private Networking | 91 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Follow this procedure to configure a gateway-to-gateway VPN tunnel using the VPN Wizard.
92 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To configure a gateway-to-gateway VPN tunnel using the VPN Wizard: 1. Log in to Gateway A on LAN A. From the main menu, select VPN Wizard . Click Next , and the Step 1 of 3 screen displays.
Chapter 6. Virtual Private Networking | 93 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The VPN Wizard Summary screen displays: To view the VPNC-recommended authentication and encryption settings used by the VPN Wizard, click the here link.
94 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: The VPN Status screen is only one of three ways to active a VPN tunnel. See Activating a VPN Tunnel on page 94 for information about the other ways.
Chapter 6. Virtual Private Networking | 95 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • Use the VPN Status screen. • Activate the VPN tunnel by pinging the remote endpoint.
96 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 4. Click Connect for the VPN tunnel that you want to activate. Activating the VPN Tunnel by Pinging the Remote Endpoint Note: This section uses 192.
Chapter 6. Virtual Private Networking | 97 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Once the connection is established, you can open a browser on the PC and enter the LAN IP address of the remote N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2.
98 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual This log shows the details of recent VPN activity, including the building of the VPN tunnel. If there is a problem with the VPN tunnel, refer to the log for information about what might be the cause of the problem.
Chapter 6. Virtual Private Networking | 99 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Using the Policy Table on the VPN Policies Screen to Deactivate a VPN Tunnel To use the VPN Policies screen to deactivate a VPN tunnel: 1. Log in to the N300 wireless modem router.
100 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 3. Click VPN Status . The Current VPN Tunnels (SAs) screen displays: 4. Click Drop for the VPN tunnel that you want to deactivate. Deleting a VPN Tunnel To delete a VPN tunnel: 1.
Chapter 6. Virtual Private Networking | 101 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • Manual Policy . For a manual keying setup in which you must specify each phase of the connection, see Using Manual Policy to Configure VPN Tunnels on page 109.
102 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual From the main menu, select VPN Policies , and then click the Add Auto Policy button to di.
Chapter 6. Virtual Private Networking | 103 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The DGND3300v2 VPN tunnel network connection fields are defined in the following table. Table 5. VPN - Auto Policy Screen Settings Fields and Settings Description General Policy Name Enter a unique name.
104 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual IKE Direction This setting is used when the router determines if the IKE policy matches the current traffic. Select an option. • Responder only .
Chapter 6. Virtual Private Networking | 105 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Parameters (Continued) SA Life Time The time interval before the SA (security association) expires. (It is automatically reestablished as required.
106 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Example of Using Auto Policy Figure 54. The following settings are assumed for this example: To use Auto Policy: 1. Set the LAN IPs on each N300 wireless modem router to different subnets and configure each correctly for the Internet.
Chapter 6. Virtual Private Networking | 107 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The VPN Auto Policy screen displays: 2. Enter these policy settings: Auto Policy Field Description General Policy Name GtoG Remote VPN Endpoint Address Type Fixed Remote VPN Endpoint Address Data 22.
108 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 3. Click Apply . The VPN Policies screen displays: 4. Repeat these steps for the N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 on LAN B.
Chapter 6. Virtual Private Networking | 109 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual a. From the main menu, select VPN Status to display the VPN Status/Log screen. Then click VPN Status to display the Current VPN Tunnels (SAs) screen: b.
110 | Chapter 6. Virtual Private Networking N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual On the main menu, select VPN Policies , and then click the Add Manual Policy radio button to display the VPN - Manual Policy screen: The following table explains the fields in the VPN - Manual Policy screen.
Chapter 6. Virtual Private Networking | 111 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Local LAN IP Address The remote VPN endpoint must have these IP addresses entered as its remote addresses. Subnet Mask Enter the network mask.
Chapter 7. Advanced Settings (Part 1) | 112 7 7. Advanced Settings (Part 1) Configuring for unique situations This chapter describes advanced features of the N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2.
Chapter 7. Advanced Settings (Part 1) | 113 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 55. If you make changes, you must click Apply for the changes to take effect. Note: If you change the LAN IP address of the N300 wireless modem router while connected through the browser, you will be disconnected.
114 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Using the N300 Wireless Modem Router as a DHCP Server By default, the N300 wireless modem.
Chapter 7. Advanced Settings (Part 1) | 115 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual the attached computers from a pool of addresses specified in this screen. Each pool address is tested before it is assigned to avoid duplicate addresses on the LAN.
116 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 4. Click Apply to enter the reserved address into the table. Note: The reserved address is not assigned until the next time the computer contacts the N300 wireless modem router’s DHCP server.
Chapter 7. Advanced Settings (Part 1) | 117 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 56. 2. Register for an account with one of the Dynamic DNS service providers whose names appear in the Service Provider list. For example, for DynDNS.
118 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 57. The WAN Setup fields are described in the following table: Setting Description.
Chapter 7. Advanced Settings (Part 1) | 119 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Setting Up a Default DMZ Server The default DMZ server feature is helpful when using some online games and videoconferencing applications that are incompatible with Network Address Translation (NAT).
120 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Configuring QoS for Internet Access To specify prioritization of traffic, you must add or create a policy for the type of traffic. To display the QoS Setup screen, from the main menu, select Advanced > QoS Setup .
Chapter 7. Advanced Settings (Part 1) | 121 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 59. 3. Click Add Priority Rule . The QoS - Priority Rules screen displays. 4. In the Priority Category list, either use the default selection of Applications , or select Online Gaming .
122 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual b. In the QoS Policy for field, enter a descriptive name for the new application or game.
Chapter 7. Advanced Settings (Part 1) | 123 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 63. 4. If the device to be prioritized appears in the MAC Device List, select it. The information from the MAC Device List is used to populate the policy name, MAC Address, and Device Name fields.
124 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • Your primary Internet access is through a cable modem to an ISP. • You have an ISDN router on your home network for connecting to the company where you are employed.
Chapter 7. Advanced Settings (Part 1) | 125 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 2. In the Route Name field, type a name for this static route. (This is for identification purposes only.) 3. Select the Private check box if you want to limit access to the LAN only.
126 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The following figure shows a wireless repeating scenario: Figure 66.
Chapter 7. Advanced Settings (Part 1) | 127 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 67. The N300 wireless modem router supports two modes of the wireless repeating function, and allows you to control wireless client association: • Wireless Repeater .
128 | Chapter 7. Advanced Settings (Part 1) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 68. 3. Select the Enable Wireless Repeating Function check box and the Wireless Base Station radio button. 4. Enter the MAC address for the repeater units.
Chapter 7. Advanced Settings (Part 1) | 129 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 2. Log in to the router that will be the repeater. Check the Wireless Settings screen, and verify that the wireless settings match the base unit exactly.
Chapter 8. Advanced Settings (Part 2) | 130 8 8. Advanced Settings (Part 2) Fine-tuning your network This chapter describes features to help you manage your N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2.
Chapter 8. Advanced Settings (Part 2) | 131 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 802.11g). In addition, many older wireless products do not support the latest security protocols, WPA and WPA2.
132 | Chapter 8. Advanced Settings (Part 2) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Optimizing Your Network Bandwidth As your network grows, it might consist of several segments of different networking technologies, each providing different throughput.
Chapter 8. Advanced Settings (Part 2) | 133 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The previous figure shows a sample network using multiple networking technologies. In this network, the two PCs with Gigabit (1000 Mbps) Ethernet adapters have a gigabit connection through the GS605 switch to the storage server.
134 | Chapter 8. Advanced Settings (Part 2) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual - Place wireless devices away from various electromagnetic noise sources, especially those in the 2400–2500 MHz frequency band.
Chapter 8. Advanced Settings (Part 2) | 135 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual If you suspect an MTU problem, a common solution is to change the MTU to 1400. If you are willing to experiment, you can gradually reduce the MTU from the maximum value of 1500 until the problem goes away.
136 | Chapter 8. Advanced Settings (Part 2) N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Figure 70. 2. The available settings and information in this screen are: • Turn UPnP On . UPnP can be enabled or disabled for automatic device configuration.
Appendix A. Troubleshooting | 137 A A. Troubleshooting Diagnosing and solving problems This appendix provides information about troubleshooting your N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2. After each problem description, instructions are provided to help you diagnose and solve the problem.
138 | Appendix A. Troubleshooting N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Troubleshooting with the LEDs After you turn on power to the N300 wireless modem router, the following sequence of events should occur: 1. When power is first applied, verify that the Power LED is on.
Appendix A. Troubleshooting | 139 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual If any of the conditions in step 2 on page 138 does not occur, see the following table.
140 | Appendix A. Troubleshooting N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Cannot Access the N300 Wireless Modem Router Menu If you are unable to access the router’s menu f.
Appendix A. Troubleshooting | 141 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Cannot Access the Internet Note: If you are installing the N300 wireless modem router and have not yet configured the Internet connection, see Chapter 1, Router Internet Setup , or the N300 Wireless Dual Band ADSL2+ Modem Router Installation Guide .
142 | Appendix A. Troubleshooting N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • Your ISP might require a login program. Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of login. • If your ISP requires a login, the login name and password might be set incorrectly.
Appendix A. Troubleshooting | 143 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Testing the LAN Path to Your Router You can ping the router from your computer to verify that the LAN path to your router is set up correctly. To ping the router from a running Windows PC: 1.
144 | Appendix A. Troubleshooting N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual If the path is functioning correctly, replies like those shown in the previous section are displayed. If you do not receive replies: • Check that your computer has the IP address of your router listed as the default gateway.
Appendix A. Troubleshooting | 145 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Wireless Connectivity Note: If you are installing the N300 wireless modem router and have not yet set up a wireless connection, see Chapter 2, Wireless Settings , or the N300 Wireless Dual Band ADSL2+ Modem Router Installation Guide .
146 | Appendix A. Troubleshooting N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual • Is your wireless signal obstructed by objects between the router and your computer? See Wireless Placement and Range Guidelines on page 16.
Appendix B. Default Configuration and Technical Specifications | 147 B B. Default Configuration and Technical Specifications This appendix provides factory default settings and technical specifications for the N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2.
148 | Appendix B. Default Configuration and Technical Specifications N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 2. Release the Restore Factory Settings button and wait for the router to reboot.The Power LED blinks red three times and then turns green when the default configuration settings have been restored.
Appendix B. Default Configuration and Technical Specifications | 149 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Firewall Inbound (communications coming in from the Internet) Di.
150 | Appendix B. Default Configuration and Technical Specifications N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Technical Specifications Feature General Network Protocol and St.
Appendix C. NETGEAR VPN Configuration | 151 C C. NETGEAR VPN Configuration Case study on how to set up a VPN This appendix is a case study on how to configure a secure IPSec VPN tunnel from a NETGEAR DGND3300v2 to a FVL328. This case study follows the VPN Consortium interoperability profile guidelines (found at http://www.
152 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Step-by-Step Configuration 1. Use the VPN Wizard to configure Gateway A (DGND3300v2) for .
Appendix C. NETGEAR VPN Configuration | 153 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 4. On Gateway B router menu, under VPN, select VPN Policies , and click the Edit button to display the VPN - Auto Policy screen: 5.
154 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Verify that the firmware is up to date, and that you have all the addresses and parameters to be set on both sides. Check that there are no firewall restrictions.
Appendix C. NETGEAR VPN Configuration | 155 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To establish VPN connectivity, Gateway A must be configured to use Dynamic DNS, and Gateway B must be configured to use a DNS host name provided by a DDNS service provider to find Gateway A.
156 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual 3. On NETGEAR Gateway B, configure the Dynamic DNS settings. Assume a correctly configured DynDNS account. a. From the main menu, select Dynamic DNS .
Appendix C. NETGEAR VPN Configuration | 157 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual The LAN addresses used in this example are as follows: a. For the connection name, enter toFVL328 . b. For the remote WAN's IP address, enter fvl328.
158 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Verify that the firmware is up to date, and make sure you have all the addresses and parameters to be set on both sides. Assure that there are no firewall restrictions.
Appendix C. NETGEAR VPN Configuration | 159 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Step 1: Configure Gateway A (VPN Router at Main Office) 1. Log in to the VPN router. Select VPN Policies to display the VPN Policies screen.
160 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Step 2: Configure Gateway B (VPN Router at Regional Office) This procedure assumes that the PC running the client has a dynamically assigned IP address.
Appendix C. NETGEAR VPN Configuration | 161 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Note: In this example, the connection name on the client side of the VPN tunnel is toGW_A.
162 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual b. Click Security Policy to show the Security Policy screen. c. In the Select Phase 1 Negotiation Mode group, select the Main Mode radio button.
Appendix C. NETGEAR VPN Configuration | 163 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual e. In the Internet Interface section, select Intel PRO/100VE Network Connection (in this example; your Ethernet adapter might be different) in the Name list, and then in the IP Addr list, enter 192.
164 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual In this step, you provide the type of encryption (DES or 3DES) to be used for this connection. This selection must match your selection in the VPN router configuration.
Appendix C. NETGEAR VPN Configuration | 165 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual To check the VPN connection, you can initiate a request from the remote PC to the VPN rou.
166 | Appendix C. NETGEAR VPN Configuration N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual This causes a continuous ping to be sent to the VPN router.
Appendix C. NETGEAR VPN Configuration | 167 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual While the connection is being established, the connection name listed in this screen shows SA before the name of the connection. When the connection is successful, the SA changes to the yellow key symbol.
Appendix D. Notification of Compliance | 168 D D. Notification of Compliance NETGEAR Wireless Routers, Gateways, APs Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices.
Appendix D. Notification of Compliance | 169 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual FCC Caution • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
170 | Appendix D. Notification of Compliance N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Cesky [Czech] NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES.
Appendix D. Notification of Compliance | 171 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual Slovensko [Slovenian] NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo č ili direktive 1999/5/ES.
Appendix E. Related Documents | 172 E E. Related Documents This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product.
Index | 173 Index Numerics 802.11 protocol mode 19 A access blocking 37 , 44 remote 59 restricting 29 restricting by MAC address 22 , 35 viewing logs 46 access points 125 account name 53 address reser.
174 | Index N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual deleting configuration 58 VPN tunnels 100 device name 57 devices attached 57 DHCP server 114 DHCP setting 54 diagnostics .
Index | 175 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual LEDs Ethernet 140 Internet 140 Power 138 Wireless 140 Live Parental Controls 32 local network, default settings 148 Log V.
176 | Index N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual releasing connection status 56 remote devices, testing path 143 remote management 59 renewing connection status 55 repeat.
Index | 177 N300 Wireless Dual Band ADSL2+ Modem Router DGND3300v2 User Manual status 94 , 167 W WAN IP address, troubleshooting 141 WAN setup 117 warning DMZ servers 119 protecting against unauthoriz.
デバイスNETGEAR DGND3300-100NASの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NETGEAR DGND3300-100NASをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNETGEAR DGND3300-100NASの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NETGEAR DGND3300-100NASの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NETGEAR DGND3300-100NASで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NETGEAR DGND3300-100NASを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNETGEAR DGND3300-100NASの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NETGEAR DGND3300-100NASに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNETGEAR DGND3300-100NASデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。