NETGEARメーカーWG602V4の使用説明書/サービス説明書
ページ先へ移動 of 78
June 2007 202-10279-0 1 NETGEAR , Inc. 4500 Great America Parkway Santa Clara, CA 95 054 USA NETGEAR 54 Mbp s Wireless Access Point WG602v4 Reference Manual.
ii 1.0, June 2007 T echnical Support Please register to obtain technical support. Please retain your proof of purchase and warranty information. T o register your product, get product support or obtai n product information and product documentation, go to www .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual iii 1.0, June 2007 Failure to follow these guidelines can resu lt in significant performance degradation or inability to wirelessly connect to the wireless access point.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual iv 1.0, June 2 007 Radio Frequency Interfer ence Requirement s and Regulatory Compliance Information This device is restricted to indoor us e due to its operation in the 2.4 GHz fre quency range.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual v 1.0, June 2007 Please go to http://www .NETGEAR.com and use the search feature to find an updated list of wi reless acce ssories approved to be used with the WG602v4 in the European Community .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual vi 1.0, June 2 007 Das Bundesamt für Zula ssungen in der T elekommunikation wurde davon unte rrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechti gt, die Serie au f die Erfüllung der V orschriften hin zu überprüfen.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual iii v1.0, June 2007 Content s About This Manual Audience, Scope, Conventions, and Formats . ......... ............. ................. ............ ............. .vii How to Use This Manual .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual iv v1.0, June 2007 Configuring Wireless Security ............ ............. ................ ............. ................ .......... 2-13 Wireless Settings Informatio n Form ...........
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual v v1.0, June 2007 Appendix A Default Configuration and T echnical Specifications Default Configuration Settings ..... ................. ............ ............. ............. ..........
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual vi v1.0, June 2007.
vii v1.0, June 2007 About This Manual The NETGEAR® 54 Mbps W ir eless Access Point WG602v4 Refer ence Manual describes how to install, configure and troubleshoot the NETGEAR WG602v4 54 Mbps W ireless Access Point. The information in this manual is intended for readers with intermediate computer and Internet skills.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual viii v1.0, June 2007 • Scope. This manual is written for the W ireless AP according to these specifications: For more information about networ k, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, “Related Documents” .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual ix v1.0, June 2007 • Printing a Chapter . Use the PDF of This Chapter link at the top left of any page. – Click the PDF of This Chapter link at the top right of any pa ge in the chapter you want to print.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual x v1.0, June 2007.
1-1 v1.0, June 2007 Chapter 1 Introduction This chapter introduces the NETGEAR WG602v4 54 Mbps W ireless Acc ess Point. Minimal prerequisites for installation are presente d in “System Requirements” on page 2-2 .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 1-2 Introduction v1.0, June 2007 • NetBIOS and WINS Support. Support for bot h NetBIOS broadcast and WINS (W indows Internet Naming Service) allows the WG602v4 to easily f it into yo ur existing W indows network.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Introduction 1-3 v1.0, June 2007 802.1 1b/g S t andards-base d W ireless Networking The NETGEAR WG602v4 54 Mbps W ireless Access Point provides a bridge between Ethernet wired LANs and 802.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 1-4 Introduction v1.0, June 2007 • MA701 802.1 1b 1 1 Mbps Compact Flash Card • W AG31 1 ProSafe 108 Mbps Dual Band PCI Card • W AG51 1 ProSafe 108 Mbps Dual Band PC Card • WGE101 802.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Introduction 1-5 v1.0, June 2007 WG602v4 Wireless Access Point Front Panel The wireless access point provides three status LEDs. The following table explai ns the L ED indicators. Figure 1-1 T able 1-1.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 1-6 Introduction v1.0, June 2007 WG602v4 Wireless Access Point Rear Panel Figure 1-2 illustrates the rear layout of the WG602v4W ireless Access Point. • Power Socket . Power adapter and cord socket for co nnecting the WG602v4 to an AC outlet.
2-1 v1.0, June 2007 Chapter 2 Inst allation and Configuration This chapter describes how to set up your NETG EAR WG602v4 54 Mbps W ireless Access Point for wireless connectivity to your LAN. The basi c configuration will enable computers with 802.1 1b or 802.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-2 Installation and Configuratio n v1.0, June 2007 • In an elevated location such as a high shelf where the wirelessly connected PCs have line-of- sight access (even if through walls).
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-3 v1.0, June 2007 Inst alling the WG602v4 Before installing the NETGEAR WG60 2v4 54 Mbps W ireless Access Point, you should make sure that your Ethernet network is up and workin g.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-4 Installation and Configuratio n v1.0, June 2007 3. A login window will display . Enter admin for your User Name and password for the password, both in lower case letters. 4. Click OK.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-5 v1.0, June 2007 When the wireless ac cess point is c onnected to the Internet, you can click the KnowledgeBase link or the Documentation link under the W eb Su pport menu to view support information or the documentation for the wireless access point.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-6 Installation and Configuratio n v1.0, June 2007 • IP Subnet Mask: 255.255.255.0 • Gateway: 0.0.0.0 If your network has a requirement to use a dif f erent IP addressing scheme, you can make those changes on this screen.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-7 v1.0, June 2007 • Country/Region. Identifies the region where the WG602v4 can be used. It may not be legal to operate the access point in a country/re g ion other tha n the country/reg ion for your area.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-8 Installation and Configuratio n v1.0, June 2007 V erifying Wireless Connectivity Using a computer with an 802.1 1b or 802.1 1g wi reless adapter with the co rrect wireless settings needed to connect to the WG602v4 (SSID, MAC ACL, WEP , WP A, etc.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-9 v1.0, June 2007 Logging Into the WG602v4 The NETGEAR WG602v4 54 Mbps W i reless Access Point can be configured remotely from Microsoft Internet Exp lorer browser version 5 .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-10 Installation and Configuration v1.0, June 2007 3. When prompted enter the default User Name admin and default Password password into the login window and click OK.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-11 v1.0, June 2007 3. Enter the NetBIOS name of the WG602v4 into the browser window (you do not need to include “www” or “http://”).
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-12 Installation and Configuration v1.0, June 2007 Wireless Security Options Unlike wired network data, your wireless data transmissions can be rece ived well beyond your walls by anyone with a compatib le adapter .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-13 v1.0, June 2007 • Use WP A-PSK or WP A2-PSK. W i-Fi Protected Access (WP A/WP A2) data encryption provides data security . WP A-PSK will block eav esdropping.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-14 Installation and Configuration v1.0, June 2007 • WP A2-PSK – WP A2 is a later version of WP A. On ly select this if all cl ients support WP A2. If selected, you must use AES encryption and a WP A passphrase (Network ke y).
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-15 v1.0, June 2007 Wireless Settings Information Form Before customizing your wireless settings, print this form and record the follo wing information.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-16 Installation and Configuration v1.0, June 2007 Configuring WEP Wireless Security If you use a wireless PC to co nfigure WEP settings, you will be disconnected when you click Apply .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-17 v1.0, June 2007 6. Click Apply to save your settings. Configuring WP A-PSK Wireless Security Not all wireless adapters support WP A. Furthermore, client softwa re is required on the client.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-18 Installation and Configuration v1.0, June 2007 Configuring WP A2-PSK Wireless Security Not all wireless adapters support WP A2. Furthermore, client sof twa re is required on the client.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-19 v1.0, June 2007 T o configure WP A-PSK and WP A2-PSK: 1. From under the Setup menu in the left-h and panel, click Security Settings .The Security Settings screen will display .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-20 Installation and Configuration v1.0, June 2007 T o res trict access based on a MA C address: 1. From under the Setup menu in the left-hand panel, click Access Contr ol . The Access Control screen will display .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Installation and Configuration 2-21 v1.0, June 2007 Now , only devices on this list will be allowed if you selected “Block all”; or all addresses will be blocked if you se lected “Allow all” Note: All options are available if using Ac cess Point mode.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 2-22 Installation and Configuration v1.0, June 2007.
3-1 v1.0, June 2007 Chapter 3 Management This chapter describes how to use the manageme nt features of your NETGEAR WG602v 4 54 Mbps W ireless Access Point. The majority of these fea tures can be found under the Management menu in the left-hand pane of the browser interface.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 3-2 Management v1.0, June 2007 This screen displays the following parameters: V iewing a List of Att ached Devices The Station List table contains a list of all devi ces associated with this wireless acc ess point in the wireless network defined by their W ireless Networ k Name (SSID).
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Management 3-3 v1.0, June 2007 To v i e w t h e St a t i o n L i s t : 1. From under Management on the main menu of the browser interface, click St a t i o n L i s t . The St a t u s L i s t screen will display .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 3-4 Management v1.0, June 2007 T o upgrade the WG602v4 software: 1. Open a web browser and go th e NETGEAR Cus tomer Service Downloads site at: 2. Browse and locate the WG602v4 upgr ade file.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Management 3-5 v1.0, June 2007 Rebooting the Wireless AP The Reboot option restarts the wirele ss access point using its current settings T o reboot the wireless a ccess point: 1. From under the Management menu, select Reboot AP .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 3-6 Management v1.0, June 2007 Changing the Administrator Password The default password is password . W e suggest that you change this password to a more secure password. However , you cannot chan ge the administrator login name.
4-1 v1.0, June 2007 Chapter 4 Advanced Configuration This chapter describes how to configure the advan ced features of your WG602v4 to one of fo ur Access Point Modes or in Client Mode.These features can be found under the Adva nced heading in the main menu on the W ireless Settings W ireless Bridging screens.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-2 Advanced Configuration v1.0, June 2007 also be serviced by this wireless access point. The WG602 must validate that the SSID, channel, and WEP configuration of the remote access poin t and match the settings of this WG602v4.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-3 v1.0, June 2007 3. Select the W ireless Point-to-Point Bridging radio butt on to enable point-to-point bridging and enter the MAC address of the Remote Access Point.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-4 Advanced Configuration v1.0, June 2007 3. V erify connectivity ac ross the network.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-5 v1.0, June 2007 . 2. Under Advanced on the main menu, click W ireless Bridging. The W ireless Bridging screen will display showing the default se ttings for the wireless access point.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-6 Advanced Configuration v1.0, June 2007 5. Check the Enable Wir eless Client Association radio box to allow wireless clients access to this wireless access point. 6. Click Apply to save your changes.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-7 v1.0, June 2007 • That the LAN network configuration of each of the W ireless APs is configure d to operate in the same LAN network address range as the other LAN devic es (routers, hubs and switches).
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-8 Advanced Configuration v1.0, June 2007 T o configure the WG602v4 in wireless repeater mode: 1. Open a web browser and log into the WG602v4 using the addressing sch eme you have set up.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-9 v1.0, June 2007 The following drawing illustrates two wireless acces s points daisy-chained together in wireless repeater mode T o configure a LAN segment utilizin g the WG602v4 in Repeater Mode: 1.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-10 Advanced C onfiguration v1.0, June 2007 Client Mode Configuration In Client Mode, the WG602v4 will operate as a C lient bridge onl .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-11 v1.0, June 2007 • DHCP Client is disabled by default, with th e default IP Address and IP Subnet Mask enabled. Reconfigure these settings, if appropriate. • MAC Cloning is disabled by default.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-12 Advanced C onfiguration v1.0, June 2007 T o connect to another AP or to a client running in Ad-Hoc Mode: 2. Click Site Survey . The Site Survey table will display a list of th e available wireless networks that you can connect to.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-13 v1.0, June 2007 • b only – Supp orts only 802.1 1b. The default is g and b. 7. Click Apply to save your settings. V erify your connection by clicking Site Survey .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-14 Advanced C onfiguration v1.0, June 2007 Advanced Wireless Settings The default advanced wireless settings usually work well. These settings should not be changed unless you are sure it is necessary .
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Advanced Configuration 4-15 v1.0, June 2007 • Fragmentation Length : This is the maximum packet si ze used for fragmentation. Packets larger than the size programmed in this field will be fragmented.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 4-16 Advanced C onfiguration v1.0, June 2007.
5-1 v1.0, June 2007 Chapter 5 T roubleshooting This chapter provides information about trou bleshooting y our NETGEAR WG602v4 54 Mb ps W ire less Access Point. After each problem descriptio n, instructions are given to help you diagnose and solve the problem.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 5-2 Troubleshooting v1.0, June 2007 • Make sure the cable connectors are securely plugge d in at the acc ess point and the network device (hub, switch, or ro uter). • Make sure the connected device is turned on.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Troubleshooting 5-3 v1.0, June 2007 • The computer with the wireless adapter ma y not have the correct TCP/IP settings to communicate with the netw ork. Restart the computer and check tha t TCP/IP is set up properly for that network.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual 5-4 Troubleshooting v1.0, June 2007.
A-1 v1.0, June 2007 Appendix A Default Configuration and T echnical S pecifications Default Configuration Settings Y ou can use the reset button located on the front of your device to reset all settings to their factory defaults. This is called a hard reset.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual A-2 Default Configuration and Technica l Specifications v1.0, June 2007 T echnical Specifications The following table lis ts the specificatio n s for the WG602v4.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Default Configuration and Te chnical Specifications A-3 v1.0, June 2007 Wireless Security: WEP and WP A-PSK Maximum Computers Per Wireless Network: Limited by the amount of wireless ne twork traffic generated by each node.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual A-4 Default Configuration and Technica l Specifications v1.0, June 2007.
Related Documents B-1 v1.0, June 2007 Appendix B Related Document s This appendix provides links to reference documents you c an use to gain a more com plete understanding of the technolog ies used in your NETGE AR product. Document Link Internet Networking and TCP/IP Addressing http://documentation.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual B-2 Related Documents v1.0, June 2007.
Index-1 v1.0, June 2007 Index Numerics 128 bits, WEP 2-14 192.168.0.227 default IP Address 2-5 default logon 2-3 255.255.255.0 default subnet mask 2-6 64 bits, WEP 2-14 802.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual Index-2 v1.0, June 2007 default subnet mask 2-6 default User Name 2-4 , 2-10 DHCP client enabled, logging in 2-8 DTIM Interval 4-15 dyna.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Ma nual Index-3 v1.0, June 2007 WP A, used with 2-14 Password default 2-4 password changing 3-6 Placement 2-1 placement guidelines 2-1 Point-to-.
NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Man ual Index-4 v1.0, June 2007 WEP authentica tion Mix, default 2-13 WG602v4 installation of 2-3 WINS Support 1-2 W ired Equivalent Privacy 2- .
デバイスNETGEAR WG602V4の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NETGEAR WG602V4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNETGEAR WG602V4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NETGEAR WG602V4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NETGEAR WG602V4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NETGEAR WG602V4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNETGEAR WG602V4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NETGEAR WG602V4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNETGEAR WG602V4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。