NETGEARメーカーWNCE3001-100NASの使用説明書/サービス説明書
ページ先へ移動 of 27
350 East Plumeria Drive San Jose, CA 95134 USA November 2011 202-10876-01 v1.0 Universal Dual Band WiFi Internet Adapter (WNCE3001) User Manual.
2 Universal Dual Band WiFi Internet Adapter (WNCE3001) © 2011 NETGEAR, Inc. All rights reserved No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc.
3 Table of Contents Chapter 1 Getting Started Unpack Your Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 1 1. Getting Started Unpack Your Adapter Open the box and remove the Internet adapter, cables, and installation guide. WNCE3001 Ethernet cable USB power cable Power adapter Stand Wall-mount sticker Figure 1.
Getting Started 5 Universal Dual Band WiFi Internet Adapter (WNCE3001) Hardware Features Top Panel with LED The WNCE3001 has one LED, which indicates the power and wireless connection status. Top panel LED status Activity Off Unit is not powered on. Solid red Link quality is poor, based on the link rate, or the USB does not supply enough power.
Getting Started 6 Universal Dual Band WiFi Internet Adapter (WNCE3001) Power Connection Options You can power on your Internet adapter using either of these methods: • Connect the WNCE3001 to an electrical outlet with the included power adapter. Figure 3.
Getting Started 7 Universal Dual Band WiFi Internet Adapter (WNCE3001) To install your Internet adapter: 1. Carefully peel off the protective film covering your adapter. Figure 5. Peel off the protective film 2. You use a computer to set up the Internet adapter.
Getting Started 8 Universal Dual Band WiFi Internet Adapter (WNCE3001) 6. Disconnect the Ethernet and USB cables from your computer. 7. Connect the Internet adapter t o your TV, XBox, or Blu-ray player.
Getting Started 9 Universal Dual Band WiFi Internet Adapter (WNCE3001) 9. Congratulations! Your installation is complete. You can return your computer to its usual setup and begin using the Internet adapter.
Getting Started 10 Universal Dual Band WiFi Internet Adapter (WNCE3001) Unless you changed the settings on the Firmware Upgrade screen (see Upgrade the Firmware on page 17), the software automatically checks for new firmware at the NETGEAR website.
Getting Started 11 Universal Dual Band WiFi Internet Adapter (WNCE3001) 2. From the menu on the left, select Setup Wizard . The following screen displays: This is the same Smart Wizard that displays during installation as described in the Installation Guide .
12 2 2. Advanced Settings To change advanced settings, connect the Internet adapter to your computer, and use your Internet browser to go to http://www.mywifiext.net as described in Prepare to Change Your Internet Adapter Settings on page 9. Device Status Screen When you connect to http://www.
Advanced Settings 13 Universal Dual Band WiFi Internet Adapter (WNCE3001) The following table describes the fields in the Device Status screen. Table 1. Device Status settings Field Description Device Status Hardware Version The hardware version of the Internet adapter.
Advanced Settings 14 Universal Dual Band WiFi Internet Adapter (WNCE3001) Show Statistics On the Device Status screen, click Show Statistics : Table 2. Show Statistics fields Field Description LAN or WLAN The statistics for the LAN (local), and wireless LAN (WLAN) ports.
Advanced Settings 15 Universal Dual Band WiFi Internet Adapter (WNCE3001) DHCP Connection Status On the Device Status screen, click DHCP Connection Status : This screen shows the status of the Internet connection. Table 3. Connection Status fields Field Description IP Address The IP address of the wireless network router.
Advanced Settings 16 Universal Dual Band WiFi Internet Adapter (WNCE3001) This screen shows whether the Internet adapter is set to get its IP address dynamically from the router (this is the most common setting), or is set with a static IP address. • Get Dynamically From Router .
Advanced Settings 17 Universal Dual Band WiFi Internet Adapter (WNCE3001) Restore Settings 1. On the Backup Settings screen, click Browse . 2. Locate and select the previously saved backup file. 3. Click Restore . A screen displays letting you know that the device has been successfully restored to the previous settings.
Advanced Settings 18 Universal Dual Band WiFi Internet Adapter (WNCE3001) To check for firmware and upgrade if it is available: 1. From the Internet adapter menu at http://www.mywifiext.net, under Maintenance, select Firmware Upgrade . The following screen displays: 2.
Advanced Settings 19 Universal Dual Band WiFi Internet Adapter (WNCE3001) • CTS/RTS Threshold (1-2347) : The packet size that is used to determine whether the Internet adapter should use the CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) mechanism for wireless packet transmission.
Advanced Settings 20 Universal Dual Band WiFi Internet Adapter (WNCE3001) • When WPS is running, the LED blinks, alternating between green and amber. • If the computer does not connect with WPS, the LED alternately blinks red and green for 5 seconds.
21 3 3. Troubleshooting Using the USB Power Cable You can connect the USB power cable to a USB port on a nearby device. If the Internet adapter is not getting enough power, the following can occur: • The LED is red right after the adapter is powered on.
Troubleshooting 22 Universal Dual Band WiFi Internet Adapter (WNCE3001) If the problem continues, make sure that your Ethernet cable is securely connected to the Internet adapter and the computer, and that the LED on the computer’s Ethernet port is on.
23 A A. Factory Settings and Technical Specifications Factory Settings You can use the Reset button on the rear panel to return your adapter to its factory settings. Reset button Figure 10. The Reset button restores factory settings Use a pin or paperclip to press the Reset button and hold it for 5 seconds until the power LED blinks amber.
Factory Settings and Technical Specifications 24 Universal Dual Band WiFi Internet Adapter (WNCE3001) Technical Specifications Feature Description Antenna 2 PCB antennas Standards 802.11a, 802.11n, 802.11g, or 802.11b Radio data rate Auto Rate Sensing Operating frequency ranges – 2.
25 B B. Notification of Compliance Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.
Notification of Compliance 26 Universal Dual Band WiFi Internet Adapter (WNCE3001) RF Exposure Information The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the requirements as set forth in CFR 47 Sections, 2.
Notification of Compliance 27 Universal Dual Band WiFi Internet Adapter (WNCE3001) Latviski [Latvian] Ar šo NETGEAR, Inc. deklarç, ka Universal Dual Band WiFi Internet Adapter (WNCE3001) atbilst Direktîvas 1999/5/EK bûtiskajâm prasîbâm un citiem ar to saistîtajiem noteikumiem.
デバイスNETGEAR WNCE3001-100NASの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NETGEAR WNCE3001-100NASをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNETGEAR WNCE3001-100NASの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NETGEAR WNCE3001-100NASの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NETGEAR WNCE3001-100NASで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NETGEAR WNCE3001-100NASを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNETGEAR WNCE3001-100NASの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NETGEAR WNCE3001-100NASに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNETGEAR WNCE3001-100NASデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。