Network TechnologiesメーカーSM-nXm-C5AV-LCDの使用説明書/サービス説明書
ページ先へ移動 of 33
MAN050 Rev 4/10/06 SM-nXm-C5A V -LCD Audio/Video Matrix Switch via CAT5 Installation and Operation Manual Used with NTI ST-C5VA-600 (XT ENDEX TM ) (NOT INCLUDED) V EEMUX ® Series NETWORK TECH NOLO GIES INCORPORATE D Te l:33 0-562 - 7070 Fax :33 0-56 2-1 999 1275 D an n er D r Au rora, OH 44 202 ww w.
i MAN050 Rev 4/10/06 TRADEMARK VEEMUX is a registered trademark of Net work T echnolo gies Inc in the U.S. and other countries COPYRIGHT Copyright © 2003-2006 by Network T echnol ogi es Inc.
ii MAN050 Rev 4/10/06 TABLE OF CONTENTS INTRODUCTION ................................................................................................................... .......................................... 1 Materials ...........................
iii MAN050 Rev 4/10/06 Figure 7- Maximum total CAT5 cable length cannot exceed 60 0 feet ............................................................... ................................. 9 Figure 8- Connect VEEMUX to LAN ..............................
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 1 INTRODUCTION The SM-nXm-C5AV-LCD (VEEMUX) is an Audio/Video Matrix switc h via CAT5 designed to work in conjunction with the NTI ST-C5VA-600 or ST-C5SVA-600 CAT 5 Audio/Video Extender (XT ENDEX).
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 2 Default User Name and Passwords The default Telnet password is admin (lower case letters only) . For instruction on u sing Telnet, see page 16. The default Web Interface user name is Administrator (upper case letter for "A" only).
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 3 XTENDEX Features and Functions 1. Green LED- communication ind icator- b links when there is valid communication bet ween the local and remote units. 2. Yellow LED- power indicator- illuminates when power has been supplied to the unit 3.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 4 XTENDEX INST ALLA TION Audio Compatibility • The audio input of the ST-C5VA-600 Au dio/Video Extender is compatible with the following standard CPU au.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 5 2. Make connections for a Local User (see Fig. 2) a) Connect the cable from the local user's VGA monitor to the female 15HD port on the L ocal Unit. b) Connect the cable from the local speakers into the 3.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 6 The Remote Unit 1. Position the Remote Unit such that the CAT5 cable, the monitor cable, speaker cable, an d the AC adapter power connector can each reach the Remote Unit comfortably. 2. Connect the monitor cable to the female 15HD video co nnector on the Remote Unit.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 7 Plug-in and Boot Up 1. Plug the power cord from the monitor into the power outlet. 2. Connect each AC adapter po wer connector to the 9VDC ports on the Remote and Local Units. Make sure the power connectors go into each port all the way.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 8 VEEMUX INST ALLA TION 1. Connect an ST-C5VA-600 Local Un it to an aud io/video source as described on pages 4-5. 2. Connect a CAT5 cable ( wired as specifie d on page 26) between the ST-C5VA-600 L ocal Unit and VEEMUX connector "AV IN 1".
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 9 Note: This total length of CAT5 cable between the ST-C5VA-600 Remote and Lo cal units cannot exceed 600 feet.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 10 USING THE VEEMUX SWITCH The VEEMUX can be controlled by either of four methods: • Using the keypad of the front panel interface • Directly via an R.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 11 Keypad Control The front panel interface keypa d a nd LCD enable the user to monit or s witch status and route any user to any audio/video source (INPUT) on the switch.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 12 Set Serial Address When selecting this menu item, the disp la y shows the current se rial address and the user is pr ompted to introduce a new serial address. One or t wo digits can b e entere d foll owed by <Enter>.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 13 Set Wserver Timeout When selecting this menu item, the display shows the current webserver timeout perio d an d offers optio nal values to change it to. Figure 17- Wserver Timeout Period The currently selected value is highlig hted.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 14 This function is particularly useful to det er mine if a lack of sound from speakers is due to failed speakers, or lack of audi o sig nal through the VEEMUX.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 15 Matrix Switcher's Control Progr am For Windows 9X, NT, 2000 and XP The Matrix Switcher's Control Program is an easy and powerful gr ap hic al program that controls NTI matrix switches through a n RS232 interface from an attached PC.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 16 Telnet Interface The Telnet Interface enables the user to control the s witch using telnet client thro ugh an Ethernet connection. T he telnet ser ver listens on port 2000 . To access the telnet interface, using the curr ent IP address t ype the following in a command shell: telnet 192.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 17 Web Interface A user may control the connections of the VEEMUX using a Web Interface via any web browser (see page 1 for web supported browsers). With the VEEMUX connected to a LAN through an Ethernet cable, a user can access the web interface controls inside the VEEMUX.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 18 Switch Page Figu re 22- W eb interface Switch p ag e The Switch page (above) disp la ys the active connections (shown in orange) and ena bles the user to control the connections of the VEEMUX. Up to 10 different connec tion configurations can b e saved and later recalled by an y connection method.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 19 To save a c onfiguraton , from the Stored Configurations user interface, use the drop-dow n lis t to select the desired slot (numbers 0-9) to save the active confi gurati on into and press the Save button.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 20 Setup Pages These settings enable the user to confi gure the VEEMUX web interface connection. • This change will take a few seconds and autom atical ly redirect the user to the IP address specified. Note: Since the webserver will be restarting all active conn ections will be logged out.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 21 Video Input Names The Video Input Names page e na bles the A dministrator to change the name of the input ports displayed on th e Switch pa ge. To change a Video Input Name, enter the nam e of the input port for the desired port number, and press Save.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 22 Update Firmware Figure 27- Web interface Update Firmware page The Update Firmware pa ge shows t he current version of the firmware and enables the Administrator to update the firmware of the VEEMUX. WARNING: Failure to carefully follow these directions can permanently damage the VEEMUX.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 23 Change Password Page Figure 28- Web interface Passw o rd page Use this page to change the pass word for accessing t he we b interface. (This pass word is also used for the telnet interface.) Be sure to make note of the new password exactly as it is case sensitive.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 24 Logout Page Figure 30- Web interface Logout page This page will enable the user to e nd the sessi on and close the web interface connection. Click on the "Press H ere to Continue Logout" button to exit the VEEMUX web interface.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 25 DEVICE DISCOVER Y TOOL In order to easily locate the VEEMUX on a network, or change n etw ork settings, the NTI Device Discovery Tool may be used. A link to the Discovery Tool is provide d on the web page that app ears when you ins ert the instructio n manual CD into your CD ROM drive.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 26 INTERCONNECTION CABLE WIRING METHOD CAT5 Cable The connection cable bet ween the VEEMUX and XTENDEX remote and l ocal units is terminated with RJ45 connectors and must be wired according to the EIA/TIA 568 B industr y standard.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 27 TROUBLSHOOTING PROBLEM: SOLUTION: No audio Check all connections and power to all dev ices. Use t he VU-Meter to determine if audio is passing through .
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 28 Appendix C- Dista nces and Resolutions for CA T5/C AT5e and CAT6 Cable s CA BLE DISTANCE (feet) RESOLUTION CAT5/CAT5e (UTP ) 600 1024x768 at 60Hz CAT5/.
NTI VEEMUX AUDIO/VIDEO MATRIX SWITCH VIA CAT5 29 Grounding These products have protective earth gr ound te rminals and are built with full attention to co nsumer saf ety. There must be an un- interruptible safety earth ground bet ween the main power source and the product's po wer cord or supplied power cord set.
デバイスNetwork Technologies SM-nXm-C5AV-LCDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Network Technologies SM-nXm-C5AV-LCDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNetwork Technologies SM-nXm-C5AV-LCDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Network Technologies SM-nXm-C5AV-LCDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Network Technologies SM-nXm-C5AV-LCDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Network Technologies SM-nXm-C5AV-LCDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNetwork Technologies SM-nXm-C5AV-LCDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Network Technologies SM-nXm-C5AV-LCDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNetwork Technologies SM-nXm-C5AV-LCDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
