New Media Technologyメーカー9212の使用説明書/サービス説明書
ページ先へ移動 of 26
IP Power 9212 User Manual.
IP POWER 9212 USER MANUAL USER MANUAL IP POWER 9212 Version: X.X 2005.07 VER. X.X, - 1 -.
Warning: any changes to this equipm ent without perm ission may cause dam ages to your equipment! This equipment has been proved to can be prevented from the influence of harm ful electronic jam ming in normal business use condit ion. IMPORTANT NOTICE 1.
IP POWER 9212 USER MANUAL Table of Content 1. INTRO DUCTIO N ..................................................................................................................... 4 F EATURES ............................................................
1. Intr oduction The IP Power 9212 is a Netw ork Controller & Se nsor with 8 DI & 8 DO. A speci fic PC or software is not needed; you can easily control devices remotely and check the device status via the Internet anywhere in the world. Using a Browser such as Internet Explore or Netsca pe, you can securel y access the unit.
IP POWER 9212 USER MANUAL 2. Befor e you start 9212 package contents One set of IP POWER 9212 Main Board : 9200 Sensor board :9201 Pro Control Board : 9202 Pro One network wire with RJ45 port .
3. Interface Description I P Power 9212 has three devices , 9200 is the netw ork m odule, and the followed picture shows its interface : 9202 is the output module and figure below shows its interface:.
IP POWER 9212 USER MANUAL 4. Hardw are & Softw are installation Before you star to use IP Power 9212, please foll ow the steps below: Check the package to make sure the contents is complete.
NOTE : Because of the polarity protective function , it won’t damage the product if you reverse the polar ity in installation. But it will cause the product cannot work properly 2. Source mode ( Voltage signal ) -- IN 1 & IN4: can be conn ected to voltage signal detectors such as smoke detector, light detector and gas det ector.
IP POWER 9212 USER MANUAL Source mode ( Voltage input) : IN1-IN4 contacts are active signal sensor. If the voltage difference between the two contacts in one set within 0V~3V, 9212 shows ON. It the volta ge difference within 4V~24V, 9212 shows OFF. So user can detect the change of equipment.
Step 1 ： Cut off th e live w ire. （ Us e a test pe ncil or scre wdriver wi t h voltage tester to identify the live wire between the two wires of electrical wire. ） NOTICE: this method m ust cut off the electrical wi re of the household appliance.
IP POWER 9212 USER MANUAL 3. You an control multi power by u se the power extension co rd NOTICE: Do not connect too much energy intens ive electrical equipment such as air conditioner, electrical heater, microwave over or over in th e same electrical outlet.
2. All the IP 92XX series, IP Kam era 9000 series/ IP Video 9100 series in the sam e subnet of the Ethernet will be found and be display in the window by the software.
IP POWER 9212 USER MANUAL 3. If can not get in the 92XX web page , please set th e segment of IP 9060(A) to be same as y our PC. * You can get your PC network information – IP Addres, Subnet Mask an.
6. Contr ol and settings through the Internet Type the new IP address of IP Power 9212 in the address field and you can enter the login web page. Input the default passwo rd 12345678(you can change the p assword as you wish) , click the OK and then you can enter the Web Control page.
IP POWER 9212 USER MANUAL IN5-IN8 contacts are short circuit sensor. If the resi stance between the two cont acts in one set within 0 Ω ~200 Ω , 9212 shows ON. If the resistance withi n 500 Ω ~ ∞ , 9212 shows OFF. So user can detect the moveme nt of equipment through the magnetic reed switch or other kind of reactive sensors.
Click the test-itself button and you will see the figure above. The states of OUT1, OUT2, OUT3 and OUT4 will separately keep in ON for 1 second, 3 s econds, 6 seconds and 8 seconds, then all back to OFF. After one period , four outp uts will keep in O FF state f or the same tim e.
IP POWER 9212 USER MANUAL Setting the password for IP Power 9212 Click the chang e passwor d option at the left window and you can enter the change password page. Follow the instructions, fill in th e old password and new password, then click the apply button to confirm .
5) When setup the setting please confirm the IP Address & Controlled IP Address is same address. Special Hardware Inter-Control - 92XX series : Use 9201 / 9212 ( DI part) to control ( IP Power 9212 & 9202 / IP Sensor 9201 / IP Motor 9203 ) 1.
IP POWER 9212 USER MANUAL B. Light : This device can control 9202 / 9212 (IP Po wer) - by change the default setting of : Normal close or norm al open C. Motor : This devi ce can control 9203(IP Motor) –control the direct ion of turning.. 3. Controlled IP Address: Set ting the Ip Address of controlled device .
Setting Sample : Receiver: 12345678@abcd.com 87654321@dcba.com Sender: abcd@168.com Mail Server: 168.com Mail Password: ●●●●●● Warning MSG: Alert After type in all the information please click “apply” fi rst to save th e change and then “s end ” to send mail.
IP POWER 9212 USER MANUAL a)Receiver : 0x200(512 bytes) b)Sender : 0x30 (48 bytes) c) Server: 0x30 (48 bytes) d) Password: 0x30 (48 bytes) e) Warning MSG(text) : 0x50 (80 byt es) –can be empty 5) Mail contents include : ”From:”, “T o:”, “Subject”, “IP Fam ily Address” GPRS for Cell Phone : Support WAP.
Step 4 after finish update please wait some second and then re-log In PS : If use DHCP please enable DHCP Note: ： 1)If the Port is 80 then you can directly update 。 2) If update fail ， you can manual reset the device and update again .
IP POWER 9212 USER MANUAL After you have setting the Ethernet and router, you can access the IP Sensor 9212 from the Internet. It will bring you all kinds of c onvenience. After assigning them different IP address and ma pping to each port of the router, you can visit each equipm ent through the Internet network.
8. Associated with other IP network product You can associate the IP Power 9212 with other IP network product of OUR in your home Ethernet, such as IP K amera 9000 ne twork camera, IP Video 910 0 network vi deo server a nd IP Sensor 9201, IP POWER 9202E to monitor the equipm ents or sensors installed in the doors or windows.
IP POWER 9212 USER MANUAL 9. F AQ Q1 : I forgot the password and can not enter the adm inistration page now, what can I do? A1 : Turn on the po wer normally, and then click th e ipedit.exe pro gram to enter the web page. Typ e in the username “superuser” and press ok then press the re set button in 9200; it will back to the default settings.
デバイスNew Media Technology 9212の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
New Media Technology 9212をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNew Media Technology 9212の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。New Media Technology 9212の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。New Media Technology 9212で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
New Media Technology 9212を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNew Media Technology 9212の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、New Media Technology 9212に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNew Media Technology 9212デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
