Niles AudioメーカーHD5の使用説明書/サービス説明書
ページ先へ移動 of 28
B LENDING H IGH F IDELITY AND A R CHITE CTURE ® INST ALLA TION & OPERA TION GUIDE ® MODEL S HIGH DEFINITION HIGH DEFINITION HIGH DEFINITION.
Congr at ulations! Thank you for choosing a High Definition In-Wall Loudspeaker from Niles. With proper installation and operation, you'll enjoy years of trouble-free use. Niles manufactures the industry's most complete line of custom installation com- ponents and accessories for audio/video systems.
Fea tur es and Benefit s Injection Molded TCC™ (Talc, Carbon and Ceramic) Woofer with Butyl Rubber Surround Vented Pole Piece, Vent ed Pole Piece and Custom Debris Screen The Niles High Definition s.
BumpBack ™ Woofer Magnet Niles engineers have utilized a unique motor construction enabling far greater “throw” or voice coil excursion. This allows a high level of bass performance to be achieved. Moisture Resistant Construction The HD loudspeakers are suitable for use in high moisture environments.
Recommended A mplifier Power For satisfactory performance, we recom- mend an amplifier with a power rating of ten to one hundred watts for the HD5; and ten to one hundred twenty-five watts for the HD6, and ten to one hundred fifty watts for the HD8 and HD8.
er, so you must connect the wire from the amplifier to the volume control and then from the volume control to the speaker. Speaker Wire Use 2-conductor speaker wire when con- necting H D speakers to your receiver or amplifier . For most applications, we rec- ommend you use 1 6 or 1 8 gauge stranded wire.
6 Speaker Placemen t Placement for Critical Listening If you like to imagine that the band or orchestra is playing in front of you as you listen to music, or you are very conscious of clarity, detail and the textures of the individ- ual instruments, you are a critical listener.
The Boundary Effect Corners can affect the bass response of the speaker powerfully! This is called the boundary effect. Y ou will emphasize par- ticular bass frequencies and cancel out other bass frequencies when you place speakers close to the wall/ceiling bound- ary or a corner wall boundary .
soundtrack to envelope you in the envi- ronment on screen. They will place back- ground music, rain sounds, traffic noise, etc. on the “surround” soundtrack.
Inst allation Fundamen tals Running the Speaker Wire in New Construction If you have doubts about whether you are capable of installing a Niles HD loud- speaker in your walls, consult a Niles dealer or professional installer. They have special tools, techniques, and experience to make the impossible possible.
of your contractor. Try to line the holes up perfectly, because it makes pulling the wire much easier. A good technique is to snap a chalk line across the face of the studs or against the bottom of the ceiling joists. Then work backward so that you can always see the holes you have already drilled.
Identify where all of your electrical, phone, and TV wiring is likely to be and plan to route around it all. You can acci- dentally induce 60 Hz hum on your speakers if you run your speaker wire right beside electrical wire for more than a few feet. T ry to keep speaker wire running par- allel to power cables at least 3 feet away.
plenum rated wire (check your local building codes, some municipalities require conduit). In traditional wood stud / drywall construc- tion you can cut the hole for the speaker and utilize the large hole to auger holes across, up or down the wall for as far as your drill bit will take you.
Inst allation o f Br acket s, Fr ames and Grilles in Ne w Constr uction Stage One: Before Drywall is Hung. Insulating the Wall Cavity. If feasible, fill the wall cavity with insula- tion at this point . Attach the wings to the bracket by snap- ping them into the sides of the bracket.
HD loudspeakers. Do not fill the holes of the grille with paint. The grille is construct- ed of aluminum with a perfectly even powder coat overall. This powder coat is an ideal primer. Remove the grilles before painting. If you are using spray paint, use two thin coats without any primer .
Inst allation o f Br acket s, F r ames and Grilles in Existing W alls IMPORTANT: Before you cut into any wall, review the sections on running wire and speaker placement.
replaced cleanly if there is an unseen obstruction behind the wall. BE V ERY CAREFUL NOT TO SAW THROUGH EXISTING WIRES, PIPES, OR STRUCTURE. IF YOU FEEL ANY EXTRA RESISTANCE AS YOU ARE CUTTING, STOP .
Installing the Speaker If the grille is already installed, remove it by using a bent paper clip or the tip of a corkscrew and pulling it away from the frame (See Figure 13) . 1 . Separate the speaker wire so that at least two inches of each conductor are free.
Speaker Phase Speaker wire has two conductors. One conductor is attached to the negative (-) terminals and one conductor is attached to the positive (+) terminals of both your speaker and your amplifier. Usually , the wire is marked for your convenience.
19 Ins t allation o f the Speak er and Grille in Ne w or Exis ting Cons tr uc tion Adjusting the Tweeter The tweeter is housed in a precision adjust- ment mechanism which enables precise aiming of the directional high frequencies to provide optimum performance.
20 Oper a tion Remo v al of Speaker and Grille Removing The Speaker If the grille is already installed, remove it by using a bent paper clip or the tip of a corkscrew and pulling it away from the frame. Utilizing two small screwdrivers or two needle nose pliers, release the snaps that hold the speaker to the frame.
21 Specifications Specifications Model HD5 Driver Compliment 5-1/4” Injection-Molded TCC Woofer with Custom Debris Screen, Butyl Rubber Surround, High BL Magnet Structure with Vented Pole Piece 1”.
22 Specifications Specifications Model HD8 Driver Compliment 8” Injection-Molded TCC Woofer with Custom Debris Screen, Butyl Rubber Surround, High BL Magnet Structure with Vented Pole Piece 1” Tet.
23 No t es Not es ________________________________ ________________________________ ________________________________ ________________________________ ________________________________ _________________.
24 No t es Not es ________________________________ ________________________________ ________________________________ ________________________________ ________________________________ _________________.
25 No t es Not es ________________________________ ________________________________ ________________________________ ________________________________ ________________________________ _________________.
26 No t es Not es ________________________________ ________________________________ ________________________________ ________________________________ ________________________________ _________________.
Niles Audio Corporation 1 233 1 S. W . 1 30 Street Miami, Florida 33 1 86 T el: (305) 238-4 3 73 Fax: (305) 238-0 1 85 www.nilesaudio.com © 2008 Niles Audio Corporation.
デバイスNiles Audio HD5の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Niles Audio HD5をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNiles Audio HD5の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Niles Audio HD5の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Niles Audio HD5で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Niles Audio HD5を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNiles Audio HD5の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Niles Audio HD5に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNiles Audio HD5デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。