Niles AudioメーカーSI-2125の使用説明書/サービス説明書
ページ先へ移動 of 20
B lending H igH F idelity and a rcHitectur e ® Systems Integration Ampli f ie r ® 230 Volts 50Hz Export Version ® INSTALLATION & OPERATION GUIDE.
CONGRATULATIONS! Thank you for purchasing the Niles SI-2125, one of the most flexible and convenient amplifiers ever offered. Like all Niles products, the SI-2125 is built to the highest standards of quality control and reliability. With proper installation and operation, you’ll enjoy years of trouble-free use.
INTRODUCTION The SI-2125 is a member of the award-winning Niles Systems Integration Amplifier family. It is designed for home theaters and whole house audio systems requiring high power.
FEATURES AND BENEFITS Real World Power The SI-2125 delivers 125 watts per channel at 8 ohms, 200 watts per channel at 4 ohms and 300 watts bridged at 8 ohms.
Turn-On Modes Th e S I- 212 5 f ea tur es th ree tur n-o n m ode s: 1. Mu si c Se nse 2. Ex te rn al Vo lta ge Tr igg er 3. M anu al Tu rn- On vi a th e f ron t pa nel s wit ch . Y ou ca n c on fig ur e t he SI -21 25 to in ter fa ce wi th any ki nd of sy ste m an d ha ve th e un it aut oma tic al ly tu rn on.
INSTALLATION CONSIDERATIONS Placement Place the SI-2125 on a flat level surface like a table or shelf. It should be placed upright so that its weight rests on the four attached feet. Placing the weight of the amplifier on the rear or front panel for even an instant will result in damage to the amplifier’s connectors and controls.
Turn-On Modes The SI-2125 draws more current than a preamplifier’s switched AC outlet can safely supply. Also, your preamplifier may “thump” at dangerous volumes if the amplifier is already on when the preamp turns on. It is usually best to turn the amplifier on only when it is needed.
Bridged Mode The SI-2125’s bridged mode switch allows you to create a more powerful amplifier by combining both channels into one (8 ohm minumum). In the bridged mode, connect the speakers to the left red positive terminal and the right red positive terminal.
Speaker selection systems allow each pair of speakers to be turned on and off from your equipment location (or even via remote control). INSTALLATION CONSIDERATIONS 8 Cable and Wire It will be easier .
AC 230V 50Hz Red “Power” LED confirms the amplifier is connected to a live AC power outlet and that the master power switch is on. Green“Active” LED lights when the amplifier circuitry has been turned on by the Turn-On circuits. Front panel “Master Power” switch turns off the entire amplifier, including the Turn-On circuitry.
Binding posts for speaker connections. Bridge mode switch IEC receptacle for AC power cord. FRONT AND REAR PANEL DETAILS 10 AC 230V 50Hz Level Adjustment screws enable you to preset the maximum system volume (or match levels with another amplifier).
INSTALLATION Setting the Turn- On Mode Switch The SI-2125 has three turn-on modes. Select which mode you desire by sliding the mode switch. See Installation Considerations on page 6 for more information about each of the turn-on modes.
12 INSTALLATION Speaker Wire Connections CAUTION! ALL SPEAKER WIRE CONNECTIONS MUST BE MADE WITH THE AMPLIFIER OFF. Bare Wire Unscrew the red or black plastic knob, insert the bare wire end into the opening, and then tighten the knob until the wire is securely clamped.
Line Level Audio Input CAUTION! THE AMPLIFIER MUST BE OFF WHENEVER YOU MAKE CHANGES TO THE INPUT CONNECTIONS. Cascade Audio Outputs The “Cascade Audio Outputs” enable you to connect another amplifier to your preamplifier output. The connectors are gold-plated RCA phono jacks.
14 INSTALLATION AC Power Plug STEP Plug the female IEC socket of the supp lie d AC cord in to the IEC receptacle on the rear of the amplifier. Plug the two-prong plug into 230V 50 Hz wall outlet. CAUTION! TYPICALLY THE PREAMP/ RECE IVE R’S SWI TCH ED OUTL ET IS NOT RATED FOR A POWER AMPLIFIER.
OPERATION Power Switch The front panel switch is a master or “vacation” power switch. No matter which turn-on mode you have selected, the master power switch will turn off all circuitry —including the sensing circuitry.
16 TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE When there is a problem consult this guide first. If the problem persists, or you have additional questions, call your local Niles dealer or Niles Technical Support at 1-305-238-4373. The most common problems relate to hook up.
17 TROUBLESHOOTING GUIDE (continued) SYMPTOM Hum from the speakers Amp will not turn on Bass sound is weak and the stereo image is “phasey” or “blurry” sounding in one room POSSIBLE CAUSES AND TEST PROCEDURE Che ck for faul ty cabl es, fa ult y so urc e mate ria l, an ungrounded phono system or a defective component.
SPECIFICATIONS 18 SPECIFICATIONS Design Principle Linear voltage/current amplification. Continuous Average Power Output 125 watts per channel RMS at 8 ohms, both channels driven. 1 75 watts per channel RMS at 4 ohms, both channels driven. 350 watts bridged channel RMS at 8 ohms.
N I L E S Niles Audio Corporation 1 23 3 1 S . W . 1 30 Stre et M iam i , Florida 33 1 86 T el: (305) 238-4 3 73 Fax: (305) 238- 01 85 www.nilesaudio.com © 2003- 200 9 Nil es Au dio Corp orat ion . Bec aus e Nil es st riv es to cont inu ous ly improve its products, Niles reserves the right to change product specications wit hout notice .
デバイスNiles Audio SI-2125の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Niles Audio SI-2125をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNiles Audio SI-2125の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Niles Audio SI-2125の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Niles Audio SI-2125で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Niles Audio SI-2125を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNiles Audio SI-2125の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Niles Audio SI-2125に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNiles Audio SI-2125デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。