Asusメーカー(WL-330)の使用説明書/サービス説明書
ページ先へ移動 of 74
® Pocket W ireless Access Point (WL-330) User Guide.
ii E1499 Revised Edition V2 December 2003 Copyright © 2003 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, .
iii Contents Notices .......................................................................................................... iv Safety statements .......................................................................................... v About this guide .
iv Contents Chapter 3: Configuration 3.1 Installing the utilities ......................................................... 3- 2 3.2 Using the Setup Wizard utility ........................................... 3- 3 3.2.1 Launching the Setup Wizard utility .
v Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation.
vi Safety st atements Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product.
vii Safety st atements Caution Statement of the FCC Radio Frequency Exposure This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247(b)(4) addressing RF Exposure from radio frequency devices.
viii This user guide contains the information you need to install and configure your ASUS Pocket Wireless Access Point (AP). How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the physical features of the ASUS Pocket Wireless AP .
ix ASUST eK COMPUTER INC. (Asia-Pacific) Address 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 T elephone +886-2-2894-3447 W eb site www .asus.com.tw T echnical Support T elephone (MB/Component) +886.
x WL -330 specif ication summar y* Standard IEEE 802.1 1b T echnology Direct Sequence Spread Spectrum (DSSS) Data T ransfer Rate 1 1Mbps (with automatic fallback to 5.5, 2 and 1Mbps) Network T ypes Supports Infrastructure and Ad-hoc networks Frequency Band 2.
Chapter 1 Product introduction This chapter describes the physical features of the ASUS Pocket Wireless Access Point. It also presents the package contents, LED indicators, and recommended network settings.
1-2 ASUS Pocket Wireless Access Point (WL-330) Product introduction 1.1 Welcome! Thank you for choosing the ASUS Pocket Wireless Access Point! The ASUS Pocket Wireless AP is an easy-to-install wireless access point and Ethernet adapter in one. Conforming to IEEE 802.
1-3 ASUS Pocket Wireless Access Point (WL-330) Product introduction 1.3 Features The ASUS Pocket Wireless AP employs the Direct Sequence Spread Spectrum (DSSS) technology to transmit and receive signals through radio waves on the 2.
1-4 ASUS Pocket Wireless Access Point (WL-330) Product introduction 1.3.2 Bottom view 1.3.3 Rear view DC-IN socket Ethernet port Reset button Mounting hook Mode switch Air vents Mounting hook. Use the mounting hook to install the device on concrete or wooden surfaces using a roundhead screw .
1-5 ASUS Pocket Wireless Access Point (WL-330) Product introduction 1.4 LED indicators The ASUS Pocket Wireless AP comes with a Power , Wireless, and Ethernet LED indicators. Refer to the table below for LED indications. LED Status Mode* Indication Power On AP/EA The device in on and ready .
1-6 ASUS Pocket Wireless Access Point (WL-330) Product introduction 1.5 Network setup The ASUS Pocket Wireless AP may be configured as an Access Point (AP) or wireless Ethernet adapter . In AP mode, the device acts as the central link between computers in a wireless network.
1-7 ASUS Pocket Wireless Access Point (WL-330) Product introduction 1.5.2 Ethernet adapter mode Ad-hoc network type In an Ad-hoc network type, the ASUS Pocket W ireless AP connects to another ASUS Pocket Wireless AP or other wireless devices. No access point (AP) is present.
1-8 ASUS Pocket Wireless Access Point (WL-330) Product introduction Access Point Single IP bridge environment In a single IP bridge environment, the device connects to an access point using a single IP address.
Installation Chapter 2 This chapter provides information on how to install the ASUS Pocket AP ..
2-2 ASUS Pocket Access Point (WL-330) Installation 2.1 System requirements Before installing the ASUS Pocket Wireless AP , make sure that your system meets the following requirements: • An Ethernet (10Base-T or 100Base-TX) adapter for wired client • At least one 802.
2-3 ASUS Pocket Access Point (WL-330) Installation 1. Connect one end of the RJ-45 cable to the Ethernet port of the device. 2. Connect the other end of the RJ-45 cable to the 10Base-T port of a network hub, switch, router , or wall patch panel. 3. Insert the universal power adapter plug to the DC-IN socket of the device.
2-4 ASUS Pocket Access Point (WL-330) Installation Ethernet adapter mode (USB bus power) 1. Connect one end of the RJ-45 cable to the Ethernet port of the device. 2. Connect the other end of the RJ-45 cable to the Ethernet port of your PC or notebook.
2-5 ASUS Pocket Access Point (WL-330) Installation 2.3 Mounting Aside from desktop placement, you may install the ASUS Pocket Wireless AP vertically on a concrete or wooden wall using the mounting hooks at the bottom of the and a mounting screw . T o mount the ASUS Pocket Wireless AP on a concrete or wooden wall: 1.
2-6 ASUS Pocket Access Point (WL-330) Installation 2.4 Operating range 2.4.1 Range The ASUS Pocket Wireless AP range is dependent on the operating environment. Every home or office layout varies in obstacles, barriers, or wall types which may reflect or absorb radio signals.
2-7 ASUS Pocket Access Point (WL-330) Installation If the cells of multiple ASUS Pocket APs overlap, then the wireless mobile client may switch from one ASUS Pocket Wireless APto another . During the transfer from one ASUS AP to another , the wireless mobile client maintains an uninterrupted connection to the network.
2-8 ASUS Pocket Access Point (WL-330) Notes.
Configuration Chapter 3 This chapter describes the ASUS Pocket Wireless AP configuration using the utilities available from the support CD..
3-2 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.1 Installing the utilities The support CD contains the utilities for configuring the ASUS Pocket Wireless AP . T o install the device utilities in your computer: 1. Insert the support CD to the optical drive.
3-3 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.2 Using the Setup Wizard utility The Setup Wizard utility allows easy configuration of the ASUS Pocket Wireless AP settings in both access point and Ethernet adapter modes. Y ou may launch the Setup Wizard utility directly from the support CD or from the Windows ® desktop.
3-4 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.2.2 Access Point (AP) mode By default, the ASUS Pocket Wireless AP is set to access point (AP) mode. The Setup Wizard auto-detects and displays the device SSID, channel, encryption, MAC, and IP addresses.
3-5 ASUS Pocket Wireless Access Point (WL-330) Configur ation Encryption tab The Encryption tab allows you to enable or disable the Wired Equivalent Privacy (WEP) encryption. WEP encryption secures data transmission between devices in a wireless network.
3-6 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.2.3 Ethernet adapter mode The Setup Wizard utility also allows you to configure the Ethernet adapter settings of the ASUS Pocket Wireless AP . T o change the Ethernet adapter settings: 1.
3-7 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3. The Ethernet Adapter Status window appears and displays the auto-detected Ethernet adapter settings including the association state, network type, SSID, encryption, MAC, and IP addresses.
3-8 ASUS Pocket Wireless Access Point (WL-330) Configur ation If you are trying to connect to an AP (Infrastructure), make sure the MAC address of the ASUS Pocket Wireless AP is included in the AP authorization table. 2. Enter the SSID in the Network Name field.
3-9 ASUS Pocket Wireless Access Point (WL-330) Configur ation 5. Enable or disable MAC cloning . MAC cloning allows the ASUS Pocket Wireless AP to use the MAC address of the host computer in communicating with other wireless device. Refer to page 3-27 for details on MAC cloning.
3-10 ASUS Pocket Wireless Access Point (WL-330) Configur ation Managing wireless networks The Preferred networks field allows you to save, configure and manage multiple wireless networks. The ASUS Pocket Wireless AP automatically connects to a wireless network with the strongest link quality in the preferred network list.
3-11 ASUS Pocket Wireless Access Point (WL-330) Configur ation T o remove a network from the preferred network list: 1. Select the network, then click the Remove button. 2. Click OK to confirm. • Y ou may also view the preferred network list in the Profiles table of the Web Configuration utility .
3-12 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.2 Device Discovery The Device Discovery utility searches and identifies the ASUS WLAN products connected to your computer . T o launch the Device Discovery from the Windows ® desktop: 1.
3-13 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.3 Web Configuration utility The Web Configuration utility allows you to configure the ASUS Pocket Wireless AP using a web browser on your computer . The following sections provide information on how to launch and use this utility .
3-14 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3. Double-click the Internet Protocol (TCP/IP) item to display the Internet Protocol (TCP/IP) Properties window . 4. Check the Use the following IP address option, then enter the IP address for the network adapter .
3-15 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.4 Launching the Web Configuration utility T o launch the Web Configuration utility: 1. Open a web browser . 2. Disable your web proxy , if you are using one. 3. T ype http://192.168.1.1 on the address bar , then press <Enter>.
3-16 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.5 Access Point mode 3.5.1 Simple Setup The Simple Setup page allows you to configure the ASUS Pocket Wireless AP configuration in access point mode. Wireless Interface SSID (Service Set Identifier).
3-17 ASUS Pocket Wireless Access Point (WL-330) Configur ation Click the Associated Stations link (beside the SSID) to displays the list of wireless device(s) associated with the ASUS Pocket Wireless AP . The list includes the wireless device(s) MAC address and connection status.
3-18 ASUS Pocket Wireless Access Point (WL-330) Configur ation Ethernet Interface The Ethernet Interface allows you to configure the network settings of the ASUS Pocket Wireless AP .
3-19 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.5.2 Access Control The Access Control page allows you to control connection requests from other devices or enable the Wireless Distribution System (WDS) feature of the ASUS Pocket Wireless AP .
3-20 ASUS Pocket Wireless Access Point (WL-330) Configur ation Wireless Distribution System The Wireless Distribution System allows your ASUS Pocket Wireless AP to communicate simultaneously with wireless clients (AP mode) and with other APs (wireless bridge mode) in your location.
3-21 ASUS Pocket Wireless Access Point (WL-330) Configur ation AP Modes Access Point Only The ASUS Pocket Wireless AP is set to Access Point Only mode by default. In this mode, the device only performs as an AP that connects wireless clients to a wired Ethernet network.
3-22 ASUS Pocket Wireless Access Point (WL-330) Configur ation WDS setup T o setup a Wireless Distribution System network: 1. Set the AP mode to Hybrid-Active . 2. Enter the MAC address(es) of the target AP(s) you wish to bridge with the ASUS Pocket Wireless AP in the MAC address list.
3-23 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.5.3 Firmware Upgrade The Firmware Upgrade page displays the product ID, firmware version, and regulation domain. This page also allows you to restore or update the ASUS Pocket Wireless AP firmware when it becomes outdated or corrupted.
3-24 ASUS Pocket Wireless Access Point (WL-330) Configur ation Regulation Domain IEEE 802.1 1b networks are regulated worldwide since these networks use the 2.4GHz ~ 2.5GHz ISM (Instrumentation, Scientific, and Medical) Band. The ASUS Pocket Wireless AP is shipped with a default regulation domain allowed in your country/location.
3-25 ASUS Pocket Wireless Access Point (WL-330) Configur ation In a multiple cell network topology , overlapping and/or adjacent cells using dif ferent channels can operate simultaneously without interference if the distance between the center frequencies is at least 30 MHz.
3-26 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.6 Ethernet adapter mode Click the link in the home page to configure the ASUS Pocket Wireless AP Ethernet adapter settings. 3.6.1 Simple Setup The Simple Setup page allows you to configure the wireless and Ethernet properties of the ASUS Pocket Wireless AP .
3-27 ASUS Pocket Wireless Access Point (WL-330) Configur ation SSID (Service Set Identifier). This field allows you to enter the SSID of the AP you wish to connect to. Enter “ANY” to connect to any availabe AP . Operating Mode. This field allows you to select the operating mode for the Ethernet adapter .
3-28 ASUS Pocket Wireless Access Point (WL-330) Configur ation Button Scan Mode Button Scan Mode. The Button Scan Mode allows you to use the reset button to connect to an access point (Infrastructure mode) or wireless device (Ad-hoc mode) saved in the Profile T able of the configuration utility or in your lcoation.
3-29 ASUS Pocket Wireless Access Point (WL-330) Configur ation When using the Alphabet Scan, the AP or wireless device you wish to connect to must have a disabled WEP encryption and available SSID. For example, if you have three saved profiles in the profile table, the ASUS Pocket AP automatically connects to the first profile.
3-30 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.6.2 Site Survey Station Status The Station Status field displays various connection information including the SSID and WEP key information of the AP or wireless device the ASUS Pocket Wireless AP is connected to.
3-31 ASUS Pocket Wireless Access Point (WL-330) Configur ation Profile Table The Profile T able displays the saved wireless connections including their SSID, channel, WEP encryption, and network type. An icon marks a saved connection to indicate whether the ASUS Pocket Wireless AP is connected or not.
3-32 ASUS Pocket Wireless Access Point (WL-330) Configur ation T o delete a saved wireless connection: 1. Check the Delete box of the wireless connection you wish to delete. 2. Click the Delete button. 3. The browser refreshes to display the remaining available wireless connections in the Profile T able.
3-33 ASUS Pocket Wireless Access Point (WL-330) Configur ation Site Survey The Site Survey field allows you to join a wireless connection. Select the wireless connection you want to join in the drop-down menu, then click the Join button. The wireless connections BSSID are marked with icons for easy identification.
3-34 ASUS Pocket Wireless Access Point (WL-330) Configur ation 2. Obtain the correct WEP keys of the wireless connection from your network administrator . 3. Enter the WEP keys you have obtained in the WEP key fields, then click Launch . Joining a wireless connection with WEP encryption 1.
3-35 ASUS Pocket Wireless Access Point (WL-330) Configur ation Joining a wireless connection with a hidden SSID and enabled WEP encryption 1. The following page appears if you selected a wireless connection with a hidden SSID and enabled WEP encryption from the Site Survey field.
3-36 ASUS Pocket Wireless Access Point (WL-330) Configur ation Parameter Default value Wireless Interface SSID ............................................................................ ANY Operating Mode ............................................
3-37 ASUS Pocket Wireless Access Point (WL-330) Configur ation 3.7 Firmware Restoration The Firmware Restoration utility is a rescue tool for an ASUS Pocket Wireless AP that failed during a previous firmware upload. This utility is available in the support CD that came with the ASUS Pocket Wireless AP package.
3-38 ASUS Pocket Access Point (WL-330) Notes.
Simple Setup Chapter 4 This chapter provides step-by-step instructions on how to setup your ASUS Pocket Wireless AP ..
4-2 ASUS Pocket Wireless Access Point (WL-330) Simple setup This simple setup guide provides instructions on how to use your ASUS Pocket Wireless AP in various operating modes and conditions.
4-3 ASUS Pocket Wireless Access Point (WL-330) Simple setup 3. Use the WLAN adapter software in your desktop PC or notebook to perform a Site Survey . Make sure the desktop PC or notebook WLAN adapter is set to Infrastructure mode. 4. Establish connection with the ASUS Pocket Wireless AP .
4-4 ASUS Pocket Wireless Access Point (WL-330) Simple setup 4.4 Connecting to another AP as an adapter or wireless bridge Follow these instructions to set your ASUS Pocket Wireless LAN AP as a WLAN adapter to access another AP with disabled WEP encryption and valid SSID.
T roubleshooting Chapter 5 This chapter contains a troubleshooting guide for solving common problems you may encounter when using the ASUS Pocket Wireless AP .
5-2 ASUS Pocket Wireless Access Point (WL-330) Tr oubleshooting Problem Action The ASUS Pocket Wireless AP does not power up. • Use a test meter to measure the voltage output of the power source through the power plug. • Check if the power plug is properly connected to the device.
5-3 ASUS Pocket Wireless Access Point (WL-330) Tr oubleshooting Problem Action When you connect the ASUS Pocket Wireless AP to a pure 10/100 Mbps hub, the Hub LED turns off while the ASUS Pocket Wireless AP Ethernet LED lights up. The ASUS Pocket Wireless AP LEDs indicate that the connection is good or bad.
5-4 ASUS Pocket Wireless Access Point (WL-330) Tr oubleshooting Problem Action • Check if the ASUS Pocket Wireless AP is in “Access Point” mode. • Check if the ASUS Pocket Wireless AP and ASUS WLAN card have the same preamble mode. A void placing the device behind a metal object.
5-5 ASUS Pocket Wireless Access Point (WL-330) Tr oubleshooting Problem Action The default subnet of the ASUS Pocket Wireless AP is “192.168.1.1”. In special cases, when the ASUS Pocket Wireless AP joins an AP network with the same IP address, reset the ASUS Pocket Wireless AP to access the web configuration page.
5-6 ASUS Pocket Wireless Access Point (WL-330) Tr oubleshooting Problem Action The ASUS Pocket Wireless AP reboots more than twice when you switch to Ethernet adapter mode. The ASUS Pocket Wireless AP , when set to Ethernet adapter mode implements the Auto-Search feature.
デバイスAsus (WL-330)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Asus (WL-330)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsus (WL-330)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Asus (WL-330)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Asus (WL-330)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Asus (WL-330)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsus (WL-330)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Asus (WL-330)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsus (WL-330)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
