NissinメーカーDi866 Professionalの使用説明書/サービス説明書
ページ先へ移動 of 11
INSTRUCTION MANUAL DIG IT AL T TL PO WER ZO OM FLA SH Please refer Nissin’s compatibility chart shown in its home page for details. http://www .nissin-japan.com or http://www.nissindigital.com SIMPLE OPERA TION When attaching Di866 to the camera, the basic flash exposure operation is fully controlled by the camera.
Di866 Flash Mode and Functions - to be set on the flash unit. Advanced functions are provided in some operation modes – to be set on the flash unit Functions by Camera setting – The flash is automatically controlled by the camera This safety instructions refer important information to use the product safely and properly .
x 4 NOTE BASIC OPERA TION SETTING THE MODE AND THE FUNCTION Remove the battery magazine and insert 4 x size AA batteries as shown in the picture. Press the on/off switch. Screen A appears, and the mode A is set. The pilot lamp blinks red showing the unit is charging.
The flash illumination coverage of Di866 responds to the lens focal length of 24mm to 105mm (full size format/film camera standard). With the latest TTL flash control system, the flash power level is always automatically controlled by the camera for the most appropriate exposure.
15 16 17 18 Flash Power can be adjusted manually at option. The photographer can set his desired exposure manually by the most appropriate power in combination with the aperture value set on the camera. 22 different power , from full power to 1/128 power , by every 1/3 stops are available.
19 20 21 22 When setting Di866 to the slave function, the zoom setting system is aut omat ical ly set for the Man ual Z oom at 24m m pos itio n. Th e zooming position can be selected manually to any other position available.In this mode, the auto-off timer is recommended to set at 60min.
Setting of Master and Slave flash: Setting Master flash: The master flash to be set is one unit only . Place the master flash on the camera and switch it on, and set to Manual function mode or set to the camera’s built-in flash on. Make sure which mode you chose, digital pre-flash flash system or analogue flash system.
27 28 29 30 SETTING THE REMOTE FLASH Group A Group B Group C Master Flash Single Group Slave Flash (Group A Setting) 1. Navigate the cursor to Group A 2. Navigate the cursor to Flash mode and select mode: TTL or M Selecting TTL 1. Navigate the cursor to the V alue Adjustment and set the EV compensation level.
31 32 33 34 Y ou do not need to set the flash unit for these functions. Functions by Camera setting Di866 offers this function at A and TTL mode. Focus the main subject and press < > button on the camera (or < FEL > button on some cameras.
35 36 37 38 When using an external power source, the number of flashes is increased and the recycling time is shortened. The following external power pack is available in option. Di866 is automatically turned off when repeating flash continuously over 20 to 30 times to protect the flash circuitry .
39 In case of the following reasons of the defect, it may void the warrantee. Please refer to the respective warrantee condition for details which varies from different countries. 1. The product is not used in accordance with the instruction of the owner's manual.
デバイスNissin Di866 Professionalの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Nissin Di866 Professionalをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNissin Di866 Professionalの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Nissin Di866 Professionalの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Nissin Di866 Professionalで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Nissin Di866 Professionalを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNissin Di866 Professionalの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Nissin Di866 Professionalに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNissin Di866 Professionalデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。