North StarメーカーM157305Hの使用説明書/サービス説明書
ページ先へ移動 of 24
K-BAR Industries, Faribault, MN, 55021 M157305H Installation, Operation, and Maintenance Manual HOT WATER PRESSURE WASHER : C leans dirty surfaces with high-pressure hot water. To the Owner: Thank you for purchasing a Northstar hot w ater pressure w asher.
2 Table of Contents Important Safety Instructions 2 Safety Features 13 Grounding Instructions 3 Maintenance Instructions 13-16 Extension Cords 3 Moving and Handling Instructions 17 Specifications 4 Lo.
3 Grounding Instructions This product must be grounded. If it shoul d malfunction or breakdown, grounding prov ides a path of least resistance for electric current to reduce the risk of electrical shock. This product is equi pped with a cord having an equipment-grounding conductor and a grounding plug.
4 Specifications Item Number 157305 157306 157307 157308 Pressure Rating 1700 psi 2700 psi 2000 psi 2750 psi Flow Output 1.5 gpm 2.5 gpm 1.5 gpm 2.5 gpm Pump Type Ceramic Triplex Plunger Ceramic Tripl.
5 Machine Component Identification 157305, 157306, 157307, 157308 Ref # Description Ref # Description Ref # Description 1 Exhaust Vent 10 Flow Switch 19 Fuel Filter 2 High Pressure Water Outlet 11 Tee.
6 Installation Instructions I.) Unpack Separate and identify all components. Use the assembly instructions in this manual for assembly. High Pressure Hose Qty-1 Wheel Retainer Qty-2 Spray Gun & Gr.
7 II.) Assembly Instructions A. 1. Carefully raise the pressure washer off the floor by using blocks or ramps. Make sure the pressure washer is secure before proceeding. 2. Install the two wheels as shown with grease zerk away from frame. 3. Slide the two wheel retainers onto the end of the axle.
8 III.) Pump Preparation *Comet Pumps Only A.) Replace shipping oil plug with vented plug. B.) Make sure the oil is 1/2 way up oil sight glass. **Cat Pumps Only A.) Remove shipping tape from oil fill cap B.) Make sure the oil is 1/2 way up oil sight glass.
9 V.) Getting Started IMPORTANT: Proper initial installation of equipment will assure more satisfactory performance, longer service life and lower maintenance cost. Make sure the pressure washer is on a level surface and in a protected area where it is not readily influenced by outside forces such as strong winds, freezing temperatures, rain, etc.
10 Operating Instructions Follow these instructions every time you use the pressure washer. I.) Pre-Operation ; A.) Position the machine for easy access to all controls. ; B.) Position the machine on a solid surface, with less than a three degree slope and so it is protected from external damage.
11 V.) Attach Nozzle Color of Nozzle: Spray Angle Used For: Red 0 Highest Impact Yellow 15 Tough Stains/ Stripping Green 25 General White 40 Light Cleaning Yellow 15 Steaming Black 65 Chemical Your pressure washer is equipped with six nozzles. To install a nozzle simply pull back the collar towards the lance and push the nozzle into the coupler.
12 2. The black, low pressure chemical nozzle must be used to spray chemicals. 3. Squeeze the spray gun trigger. The chemical injector will draw the chemical into the water stream. 4. Spray detergent onto the surface and allow it to soak. Chemicals need time to work properly.
13 Safety Features I.) Safety Relief The safety relief valve is a backup safety feature. If the unloader malfunctions, the safety relief valve will open and relieve system pressure. WARNING: If the safety relief valve ever discharges water, turn the unit off and do not use the machine.
14 Cleaning The Inlet Filter WARNING: Check whether dangerous chemicals have been used and take precautions when handling filters. A.) Unscrew clear tube by hand. B.) Remove Inlet filter C.) Run water though to clean filter Checking the Tire Air Pressure A.
15 Coil Descaling In hard water areas, scale build-up within the heating coil will occur. Scale deposits will decrease the water temperature rise and may eventually clog the heating coil. 1. Mix scale remover in a 5 gallon bucket and elevate the bucket so it is higher than the pump.
16 Electrodes On a yearly basis the electrodes should be inspected and any necessary adjustments made. 1. Tip the machine back until it rests on the frame. 2. Remove the 4 nuts that attach the burner to the heating chamber. You do not have to disconnect the fuel lines or the electric cords.
17 Moving and Handling Instructions Maneuvering Your Pressure Washer 1.) Pull the handle back with both hands. 2.) Rotate the handle downward to a comfortable height. 3.) Push the pressure washer forward as you walk. Lifting Your Pressure Washer 1.) To reduce risk of injury, it is recommended to use a hoist to lift this pressure washer.
18 Troubleshooting Guide Pressure Washer Will Not Run - No Power Causes Solutions Machine not plugged in Plug machine in GFCI tripped Make sure machine is dry Press RESET on the GFCI Machine turned OF.
19 M157305H - 157305,157306,157307, 157308 Parts Breakdown.
20 ITEM PART # DESCRIPTION QTY MODEL ITEM PA RT # DESCRIPTIO N QTY MODEL 1 38525 50’ PW Hose Assy 1 ALL 35 38379 Swivel Fitting, 6MP-8FPS 1 ALL 2 777914 Quick Couple, 3/8” FPT 1 ALL 36 5027 Elbow,.
21 ITEM PART # DESCRIPTION QTY MODEL 779402 Comet BXD 1617 1 157305 779403 Comet BXD 2527G-E 1 157306 778154 Cat 2DX 1 157307 1 38518 Cat 3DX 1 157308 2 35918 Thermal Protector, 1/4” 1 157307, 15730.
22.
23.
24.
デバイスNorth Star M157305Hの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
North Star M157305Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNorth Star M157305Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。North Star M157305Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。North Star M157305Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
North Star M157305Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNorth Star M157305Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、North Star M157305Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNorth Star M157305Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。