Numark IndustriesメーカーTT200の使用説明書/サービス説明書
ページ先へ移動 of 13
OPERATING INSTRUCTIONS CONTENTS Setup & Installation 2 Platter Setup 3 Cartridg e Setup 4 Interchangin g T onearm T ubes 5 To n e A r m S e t u p 6 Cont ro ls 7 Cable Setup 10 Specifications 11 T .
SETUP & INSTALLATION This turntable has been designed exclusive ly for DJ use and can be setup in a v ariety of different w ays dependin g on your mixing style. The tu rntable sh ould rest on a level and st able surface t hat is clear of obstr uctions.
PLATTER SETUP WARNING: Incorrect Platte r setup can lead t o poor turntable performance , platter instability , or permanent motor damage. 1. Start by in specting the bottom of the aluminum pla tter to check that bo th locking pins ha ve rubber fittings on them.
CARTRIDGE SETUP For Head Shell Mounted Cartridg es: The cartridge th at comes with t his turntable sho uld be preinstalled on the head shell. If it isn't, please follow the below i nstructions for installing a c artridge onto the head sh ell. 1. Position the head shell and the cartridge so that the four connector p ins are visible.
INTERCHANGING TONEARM TUBES (sold seperately) WARNING: An incompl ete underst anding of this pr ocedure could lead to permanent damage to the headshell, your reco rds, or the tonearm assemb ly . NOTICE: Interchangi ng tonearm tubes un necessarily m ay shorten the life o f the tonearm tube s and/or tonea rm comp onents.
TONE ARM SETUP A properly adjusted tone arm and cartridge setup wi ll minimize viny l record wear and optimize the performance of the turntable. Follow these simple s teps fo r setti ng the tone arm o.
PAG E 7 CON T R OL S CONTROLS General Controls 1. P owe r Button Pushing this button down turns on the turntable . It illuminates red w hen the turntable is switched on. 2. Start/ Stop Butt ons These buttons start and stop the turntable mo tor . Both buttons hav e the same function.
CABLE SETUP PAGE 8 CONTROLS continued Tone Arm Parts 10. Counterweight and Scale Ring and S- W eight 11 10 The Counterweight is used to balance the head shell and cartridg e assembly so t hat the prop er amount of stylus pressure is applied to the record.
PAG E 9 CON T R OL S CONTROLS continued Bottom Parts 18. Adjustable Rubber Dampening Feet When all of the feet of the turntable are completely ti ghte ned, the to p flat surfa ce of t he tu rntable will be at 85mm. Unscrewing these feet r aises the turn table up to compensa te for unleveled sur faces.
CABLE SETUP PAGE 10 CABLE SE TUP This turntable is shippe d with two sets of special cabl es: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord w/ground wire NOTE: Before connecting any cables, make sure that th e voltage selector switch is set to the proper setting! Making the power and audio connections: 1.
SPECIFICATIONS Turntable Section: T ype: 3 speed, fully manual Motor: Direct Drive- 8 P ole, 3 Phase Starting T orque: 1.6 kg/cm Start Time: 0-33.33 RPM in 0.8 sec Braking S ystem: Electronic Se rvo Br ake Platter: Aluminum Diecast Speeds: 33.33, 45, and 78 RPM W ow & Flutt er: <0.
Problem Cause? Solution T urntable d oes not turn on. D isconnected Power Cord? Connect Power Cord. The sou nd leve l is very l ow. The T urn table is not conn ected to a device wit h a PHONO preamp . Connect the device to a preamp DJ mixer or an AV receiver that has an input la beled PHONO , not AU X or LINE.
INSIDE THE BOX: (1) TT-200 w/Straight Tonearm (1) Aluminum Platter (1) Slipmat (1) Head shell (1) 2.5 Gram Headshell Weight (1) Counter Weight (1) 45 RPM Adapter (1) IEC Power Cable (1) RCA Cord w/ Ground Wire (1) Service Tool TT -200 Manual /English, R3.
デバイスNumark Industries TT200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Numark Industries TT200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNumark Industries TT200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Numark Industries TT200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Numark Industries TT200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Numark Industries TT200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNumark Industries TT200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Numark Industries TT200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNumark Industries TT200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
