NumarkメーカーTT-1650の使用説明書/サービス説明書
ページ先へ移動 of 16
TT-1650 Operating Instructions (1) TT-1650 Turntable (1) Aluminum Platter (1) IEC Power Cable (1) RCA Cord w/ Ground Wire (1) Slipmat INSIDE THE BOX: (1) Headshell w/ Cartrdige (1) Counter Weight.
PAGE 1 SAFETY PRECAUTIONS Thank you for buying this Numark product. Please read these operating instructions so you will know how to oper ate this equipment properly . After you have finished reading these instructions, k eep them for future reference.
PAGE 2 T ABLE OF CONTENTS IMPORT ANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PAGE 3 CONTROLS CONTROLS General Controls 1. Power Button Pushing this button down turns on the turntable. 2. Start/Stop Buttons These buttons start and stop the turntable motor . Both buttons ha ve the same function. 3. Platter This turntable has a special edge design that has been optimized for "dr agged" platter slow downs.
PAG E 4 CONTROLS CONTROLS continued Tone Arm Parts 7. Counter W eight and Scale Ring The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. 8. Anti-Skate Adjustment This knob is used to compensate for inward tr acking forces.
PAGE 5 SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a v ariety of different wa ys depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions.
PAGE 6 PLA T TER SETUP 1. Locking Pins 3. ALIGNED PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instabilit y or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them.
PAGE 7 CABLE SETUP CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord w/ground wire NOTE: Before connecting an y cables, make sure that the voltage selector switch is set to the proper setting, either 110V or 220V depending on region.
PAGE 8 TONE ARM SETUP TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: Balancing the Tone Arm 1.
PAGE 9 CARTRIDGE SETUP CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell.
OPERA TION PAGE 10 OPERATION This turntable was designed to accommodate a v ariety of different mixing styles. Here are some general operation guidelines to optimize the performance of the turntable. 1. Do not place the turntable on or near a speaker or subwoofer .
PAGE 11 WARRANTY LIMITED PRODUCT WARRANTY 1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") w arrants to the original purchaser that NUMARK'S products; including but.
PAGE 12 RETURN INFORMA TION RETURN INFORMATION (US ONL Y) a) A Return A uthorization number must be obtained from Numark through the address or phone numbers below. b) A copy of the original sales receipt must also be included for the equipment to be repaired under warr anty .
PAGE 13 SPECIFICA TIONS SPECIFICATIONS Turntable Section: T ype: 2 speed, fully manual Motor: Direct Drive Starting T orque: > 1 Kg/cfm Platter: Aluminum Diecast Speed: 33.
TROUBLE SHOOTING PAGE 14 T urntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low . The T urntable is not connected to a device with a PHONO preamp. Connect the device to a preamp DJ mixer or an A V receiver that has an input labeled PHONO, not AUX or LINE.
Copyright Numark Industries, LLC 2002 T T -1600, T T -1650 Manual /English - rev B.
デバイスNumark TT-1650の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Numark TT-1650をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNumark TT-1650の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Numark TT-1650の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Numark TT-1650で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Numark TT-1650を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNumark TT-1650の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Numark TT-1650に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNumark TT-1650デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
