O'NeilメーカーFor 8100の使用説明書/サービス説明書
ページ先へ移動 of 24
User's Guide MICROFLASH 8I.
.
TABLE OF CONTENTS 3 microFlash 8 i Printer 4 Open View 4 Closed View 4 Installing a Radio Card 5 Using the Ribbon 6 Installing the Ribbon 6 Removing the Ribbon 7 Installing and/or Replacing Batteries .
MICROFLASH 8I PRINTER USER'S GUIDE 4 microFlash 8i Printer Open View Closed View Battery cavit y Battery cable Access cover Locking lever (green knob) Control panel Printer assembly Figure 1 Pap .
MICROFLA SH 8I PRINTER USER'S GUIDE 5 Installing a Radio Card 1. Open the printer’s co ver . 2. Push in the locking tab and lift the access cover (Figures 3 and 4). 3. Insert the radio card f ace up into the PCMCIA slot (Figure 5). 4. Close the access cover and press down until the locking tab clicks into place.
MICROFLASH 8I PRINTER USER'S GUIDE 6 Using the Ribbon Installing the Ribbon The printer ships without a ri bbon installed. T o install a ribbon, perform the f ollowing: 1. Remo ve the ribbon from its packaging. 2. Open the printer’s co ver . 3.
MICROFLA SH 8I PRINTER USER'S GUIDE 7 Removing the Ribbon 1. Slide the printhead awa y from the edge of t he printer (Figure 9). 2. Pull the ribbon away fr om the printer (Figure 10).
MICROFLASH 8I PRINTER USER'S GUIDE 8 Installing and/or Replacing Batteries 1. Open the printer ’ s cover . V erify the control panel is faci ng to wa rd y ou . 2. Place the battery in the batte ry cavity (Figure 11) . 3. Connect the printer's cable connector to the bat tery (Figures 12a and 12b).
MICROFLA SH 8I PRINTER USER'S GUIDE 9 4. Install the battery strap o ver the printer's cable connector and the battery so that they are both h eld in place (Figure 13). 5. Close the printer’s co ver . 6. Charge the battery . F or more information, see Charging the Ba ttery on page 9 .
MICROFLASH 8I PRINTER USER'S GUIDE 10 Loading Paper 1. Open the two latches on the side of the printer’ s cover and lift the printer’ s cove r to the fully open position. 2. Depress the locking lever (green knob) to open the print mechanism (Figure 14).
MICROFLA SH 8I PRINTER USER'S GUIDE 11 5. Fold the stack of paper in half with the short sides together and with the top of the form c oming out from the inside fold (Figure 17). 6. Place the paper into the paper cavity with the bottom edges under the paper lip in the bottom of the cavit y (Figure 18).
MICROFLASH 8I PRINTER USER'S GUIDE 12 Paper Quantity Guidelines Tearing the Paper 1. Set th e paper to to p of fo rm. F or more information, see Setting T op of F orm (TOF) on page 13 . 2. Grab one side of the paper at a leading edge and pull up.
MICROFLA SH 8I PRINTER USER'S GUIDE 13 Setting Top of Form (TOF) 1. Press button 1 to turn on the printer . 2. Position the paper by pr essing button 1 until the end of the paper is at the edge of the ca se. If necessary , press button 2 to back feed the paper .
MICROFLASH 8I PRINTER USER'S GUIDE 14 Using Buttons and Indicators Control Panel LED Indicators Charge LED LED Description Ac tion Solid red Charging in progr ess. None. Red f la s h - slow Battery disconnected. Low temperatur e. Connect battery .
MICROFLA SH 8I PRINTER USER'S GUIDE 15 Pow e r L E D Button Functions Charge LED LED Description Action Green P ower on. None. Green flash - fast Pap e r o ut , h e a d j a m . Install pa per , check for paper jam. Green to or ange alternating flash - fast If a rad io card is installed, indicates radio and printer are on.
Audio Indicators LED Description Action Long series of short beeps Head jam. Check for paper jam. 1 short RF power is on (when RF power button is pressed and RF power was off ). None. 1 long Boot code is starting or restarting (occurs more than once when downloading new firmware).
MICROFLA SH 8I PRINTER USER'S GUIDE 17 Using Power Options Use the following options to power the printer: • AC AC/DC Power Supply • DC Cigarette Adapter • Batteries NiMH The red-tagged cable attached to the printer connects to the AC adapter cable.
MICROFLASH 8I PRINTER USER'S GUIDE 18 Attaching Cables The RJ11 (telephone style) connector at tached to the printer connects to your notebook and/or computer or handheld (HHC) using an optional data cable or handheld cradle. Configuring the Printer The printer has many configurable set tings.
19 MICROFLA SH 8I PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Clas s B digital device , pursuant to Pa rt 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf ul interference in a residential installation.
20 MICROFLASH 8I PRINTER USER'S GUIDE Warranty The Company warr ants that O'Neil Pro duct Deve lopment, Inc.'s products are free from defects in manufacturi ng materials and workmanship for one (1) year f rom date of original purchase to Buyer/Distributor (OEMs 90 days from the da te of purchase).
21 MICROFLA SH 8I PRINTER USER'S GUIDE.
.
.
W orld Headquarters O'Neil Product Development 8 Mason Irvine, CA 92618-2705 Ph: 949.458.0500 Fx: 949.458.0708 Europe 6 Joplin Court, Crownhill Milton Keynes MK8 0JP United Kingdom Ph: +44 (0) 1908 635360 Fx: +44 (0) 1908 635361 AustralAsia 1/8 Railway T errace Dutton Park QLD 4102 Austalia Ph: +61 (7) 3255 3360 Fx: +61 (7) 3255 3365 WWW .
デバイスO'Neil For 8100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
O'Neil For 8100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはO'Neil For 8100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。O'Neil For 8100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。O'Neil For 8100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
O'Neil For 8100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はO'Neil For 8100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、O'Neil For 8100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちO'Neil For 8100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
