Omega EngineeringメーカーDPS3301の使用説明書/サービス説明書
ページ先へ移動 of 26
http://www.omega.com e - mail: info@omega.com DPS3301 Series Wall-Mount Programmable Temperature Monitor.
Page 2 SPECIFICATIONS .......................................................................................................................................................... 4 DESCRIPTION ............................................................
Page 3 R ESETTING : ................................................................................................................................................................... 16 E LECTRO -M ECHANICAL R ELAY O PTIO N ..........................
Page 4 SPECIFICATIONS Typical @ 25 C and rated supply voltage unless otherwise specified. INPUTS: • Input types: J,K,T,E,R,S,B t/c, RTD, Voltage, Millivolt, Current & thermistor • Cold junction compensation erro r: +/- 0.
Page 5 DESCRIPTION Housed in a wall-mount, water-tight plastic enclos ure, the DPS3301 Series is a powerful temperature monitor/indicator. It accepts a single Thermocouple, RTD or Thermistor sensor input and then displays the temperature in either degrees C or F.
Page 6 How to Reset and Program Th ermocouple Type (or RTD) How to Reset and Program Th ermocouple Type (or RTD) A DPS3301-TC that is calibrated for a J, K, T, or E ty pe thermocouple or an RTD model may be programmed for a specific thermocouple, or RTD ( 385/392) type, by going into SETUP mode (Look unde r ‘SETUP’).
Page 7 SEE SETUP ON HOW TO SELECT ONE OF THE DISPLAY MODES. RETAINING USER SETTINGS ON POWER DOWN DPS3301 saves all the programmed parameters in an EEPROM (electrically erasable programmable read only memory). An EEPROM stores the programmed parame ters even when the power is removed from the unit.
Page 8 FLOW CHART PROGRAM CONTROLLER Back to SETUP COLD JUNCTION CALIBRATION INPUT CALIBRATION DISPLAY TIM E DISPLAY OPTION a. Process b. Setpt Devn. c.
Page 9 SETUP MODE Setup is used for configuring vari ous par ameters of DPS3301 unit. These parameters include entering limits, timers, dead-bands etc. Entering and Exiting Setup Mode: To get into setup mode, press and hold SETUP key. The display will show ELPSd t and then the value of elapsed time.
Page 10 'PROGRAM CONTROLLER' MODE Display Time On entering Program Controller mode, the very first step lets you program is the display time. This determines the length of time (in seconds) that any VALUE is displayed before message, such as ‘PROCESS’ is flashed.
Page 11 Cold Junction adjustment: After setting Heat/Cool mode, the next parameter is the cold junction reference temperature adjustment. The display will first show 'COLd JN' , and then the cold junction temperature will be indicated. Use ‘^DIGv’ key to adjust until the display reads the proper temperature.
Page 12 NOTE 1: The unit must be powered up for at least ten minutes before any adjustments are made. NOTE 2: For calibrating units with RTD or Thermistor inputs, connect the source to input c onnector, dial in a temperature near high end of the scale and adjust gain potentiometer on the back of the unit (See figure 7 for reference).
Page 13 Programming Limit 3: As Process Limit: If Limit 3, in the above step, was configured as a Pro cess limit, then the message displayed on entering this mode will be ‘PrG Lt3’ . This will be followed by displaying the current value of Limit 3 .
Page 14 energized. In Mode 1 the timer is ON for a programmed amount of time after a temperature limit is reached (limit1 for Timer 1 and Limit 2 for Tim er 2). When programmed amount of tim e has elapsed, the timer is de- energized. Mode 2 is used to produce a programmable tim e delay af ter the temperature limit is reached.
Page 15 Audio Alarm On/Off: This unit supports an audio alarm option which comes on when ever a limit value is exceeded. This alarm can be turned On or Off, as desired. The selection is made by pushing ‘^DIGv’ key. If the alarm is ON, the display will read ‘ALR ON’ (Alarm On).
Page 16 setpoing will be indicated. Deviation Alarm: Limit 4 has the capability to work either as process or as deviation alarm. This configuration is done during setup (look under SETUP). Also entered during setup is the alarm value. Programmed value is absolute and it works on negative as well as positive deviation e.
Page 17 limit alarms. (Check model number printed on the unit fo r option). If ordered with relays, then these relays are programmed during Setup to operate as Normally Op en (NO) or Normally Closed (NC). The default setting is Normally Open. Each of these limit relays pr ovides a switched output whenever a limit is reached.
Page 18 To display Timer #1 value, push the TIME key twice . The first push shows elapsed time, while the second push will first display 'tr1 Cnt' (for T ime r1 Count) and then Timer 1 value. To display Timer #2 value, push TIMER key three times .
Page 19 HIGH AND LOW PEAKS A useful feature provided by the DPS3301 system is its ability to track high and low temperature peaks. This function is useful if a process must be left unattended for a long period of time, and it is necessary to find temperature extremes during the unattended period.
Page 20 ‘SIGNAL CONNECTOR’ in figure 4. Also indicated ar e the input signal’ s positive and negative polarities for thermocouple connection. These markings are also on the printed circuit board in front of the connector.
Page 21 FIG 4. DPS3301 Series TERMINAL COMPARTMENT 1 2 3 4 5 6 7 8 9 10 11 12 1 3 14 POSITIVE SIGNAL NEGATIVE SIGNAL GAIN ADJ UST OFFSET ADJUST (For Millivolt, T/C input) OUTPUT CONNECTOR PWR GND L2 L.
DIRECT INTERFACE TO UNIVERSAL RELAY MODULE For high amperage loads, DPS3300 series units can be used in conjunction with Universal Relay Module (Model RELAY-URM400/800) which provide up to e ight 15 ampere relays. Both open collector and relay models can be interfaced directly to RELAY-URM400/800 units.
Page 23 MOUNTING 120mm 4.72” PICTURE HANGING -TY PE FIXTURE FOR MOUNTI NG SCREW MOUNTING SCREW SLOTS (Mount Screws from front—see picture below ) 151mm 5.
Page 24 Page 24.
Page 25 Page 25.
Page 26 M4300/0907.
デバイスOmega Engineering DPS3301の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Omega Engineering DPS3301をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOmega Engineering DPS3301の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Omega Engineering DPS3301の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Omega Engineering DPS3301で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Omega Engineering DPS3301を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOmega Engineering DPS3301の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Omega Engineering DPS3301に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOmega Engineering DPS3301デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。