OnkyoメーカーA-9030の使用説明書/サービス説明書
ページ先へ移動 of 32
Integrated Amplifier A-9050/ A-9030 Instruction Manual Thank you for purchasing an Onkyo In tegrated Amplifier. Please read this manual tho roughly before making connections and plu gging in the unit.
2 En Introduction Important Safety Instructions 1. Read these ins tructions. 2. Keep these instruct ions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
3 En Precautions 1. Recording Copyright —Unless it’s for personal use only, recording copyrighted ma terial is illegal without the permission of the copyright holder. 2. AC Fuse —The AC fuse inside the unit is not user- serviceable. If you cannot tu rn o n the unit, contact your Onkyo dealer.
4 En For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
5 En Features A-9050 Integrated Digital Amplifier • Three-stage Inverted Darlingto n Circuitry • Digital Inputs (Optical/Coax ial) • Wolfson 192 kHz/24 bit DACs withDIDRC Circuitry Inside (WM8718) • Phase Matching Bass Technology • 1.6 mm F ull Flat Chass is • 75 W/ch (1 kHz, 8 ohms, 0.
6 En Contents Introduction Important Safety Instructions ............................ ..............2 Precautions ....................................................................... 3 Supplied Accessories ..........................................
7 En Before Using the Integrated Amplifier Note • If the remote controller doesn’t work reliably, try replacing the batteries. • Don’t mix new and old batteries or diff erent types of batteries. • If you intend not to use th e re mote controller for a long time, remove the batteries to prev ent damage fr om leakage or corrosion.
8 En Getting to Know the Integrated Amplifier For detailed information , se e the pages in parentheses. a 8 ON/STANDBY button ( ➔ page 21 ) Sets the integrated amplifier to On or Standby. b Remote control sensor ( ➔ page 7 ) Receives control signals from the remot e controller.
9 En a GND screw Connects the turntable’s ground wire. b u MODE selector (A-9050 only) c DIGITAL IN OPTICAL D3 jack (A-9050 only) Connects components such as CD players with optical digital audio output. d DIGITAL IN COAXIAL D1/D2 jacks (A-9050 only) Connect components such as CD players with coaxial digital audio output.
10 En For detailed i nformat ion, see the pages in parentheses. a 8 button ( ➔ page 21 ) Sets the integrated amplifier to On or Standby. b DIMMER button Adjusts the display brightness. c ! / " / # / $ and ENTER buttons Select and adjust settings.
11 En *: A-9050 only Connecting Terminal LINE1/D1* LINE2/D2* LINE3/D3* Component Button on Remote Controller CD Player TUNER u DOCK 1 88 8 2 DIMMER DIMMER DIMMER 3 ! / " ! / " (Tuning Up/ Down) ! / " # / $ # / $ (Preset Up/Down ) ENTER ENTER ENTER 4 8 CD 8 5 DISPLAY Display the current input and settings.
12 En Connections Connections ■ Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables , and twist the bare wire s tightly, as shown. ■ Banana Plugs (North Amer ican models ) • If you are using banana plugs, tighten the speake r terminal bef ore inserting the banana plu g.
13 En Note • Make sure that the wires do no t touch metal parts on the back panel or elsewhere. • Y plugs cannot be connected. • Two sets of speakers (Speak ers A and Speakers B) can be connected to the integr ated amplifier. You can select which speakers to output audio to when listeni ng to music.
14 En Note • Push plugs in all the way to make good connections (loose connections can cau se noise or malfunctions). • To prevent interference, keep audio cables away from power cords and speaker cables.
15 En This is an example of conne ction using the CD Player . Digital Connection (A-9050 only) Tip • The CD player can be connecte d to the COAXIAL D1 or D2 jack or the OPTICAL D3 jack. However, when using the u interlock function, be sure to connect the CD player to the COAXIAL D1 jack.
16 En This is an e xample of conn ection using th e Tuner. Digital Connection (A- 9050 only) Tip • The Tuner can be connected to the COAXIAL D1 or D2 jack or the OPTICAL D3 jack. However, when using the u interlock function, be sure to connect the Tuner to the COAXIAL D2 jack.
17 En This is an example of connection using the Onkyo u Dock. Digital Connection (A-9050 only) Tip • An Onkyo Dock can be connected to the COAXIAL D1 or D2 jack or the OPTICAL D3 jack. However, w hen using the u interlock function, be sure to connect the Onkyo Dock to the OPTICAL D3 jack.
18 En With u (Remote Interactive) , you can use th e following special functions: ■ Auto Power On When you start playback on a component connected via u while the integrated amplifier is o n Standby, the integrated ampli fier will automatical ly turn on and select that component as the input source.
19 En The PHONO input jacks are for use with moving-magnet (MM) type cartridges. Use an analog audio cable to connect the PHONO L/R jacks to the audio output jack s on the turntable, as shown. If your amplifier has shorti ng pin plugs, remove the shorting pin pl ugs before conn ecting your tur ntable.
20 En A subwoofer with a built-in power amplifier can be connected to be used. Connect LINE INPUT on the subwoofer with a built- in power amplifier to PRE OUT: SUBWOOFER termin al on the integrated ampli fier. If your subwoofer does not ha ve a built-in amplifier, connect the input jack of your amplifier to the pre out jack of the subwoofer.
21 En Turning On & Basi c Operations Basic Operations Turning On the Integrated Am plifier ■ Operating with the remote controller ■ Operating on the in tegrated amplifier Tip • After a certain time of warming up, the internal temperatur e of the integrated amplifier stabiliz es, and the sound is softened.
22 En You can select to output sound from Speakers A, Speakers B, or both A + B. Note • While headphones are connected, this setting is disabled. • When this setting is set to A + B , the impedance of speakers is restricted . For further details, see “Connecting Your Speakers” ( ➔ page 12 ).
23 En You can switch inputs to select the desired source component. Choose an input from the following: LINE1, LINE2, LINE3, LINE4, LINE5, PHONO ( D1, D2, D3 (A-9050 only)) The LED corresponding to the selected input will lig ht up. Tip • The LED will blink when D1 , D2 or D3 is selected and a signal is not input.
24 En You can adjust the bass, tr eble and left/right output balance respectively. ■ Operating on the in tegrated amplifier Tip • By default, bass, treble and bala nce is set to the center position. Note • While the Direct function is enabled, ba ss and treble are disabled.
25 En Advanced Op erations Custom Setup When the Auto Standby (ASb) function is activated, the integrated amplifier will automatically enter Standby mode if there is no operatio n for 30 minutes with no audio signal input. You can set the impedance of the speakers that you connect to the unit.
26 En Others Troubleshooting First check the followings. Since the issue may be caus ed by other components that are connected, be su re to also check them while referring to their m anuals. Further product operating procedures and FAQs (frequently asked questions) ar e available from the Onkyo web site.
27 En There’s no soun d. • Make sure that the Onkyo Dock is connected to the integrated amplifier properly. • Make sure that no video content is being played. • Reset the iPod. Other • When the Auto Standby (ASb) function is activated, the power of the Onkyo Dock connected via u is automatically turn ed off ( ➔ page 25 ).
28 En Specifications ■ Audio Inputs ■ Audio Outputs ■ Others Specification s and features are subject to c hange without n otice. A-9050 A-9030 Rated Ou tput Power (North Am erican) (FTC) 75 watts mi nimum continuo us power per channel, 8 o hm loads, 2 c hannels drive n at 1 kHz, with a maximum to tal harmoni c distortion of 0.
29 En MEMO.
30 En MEMO.
31 En MEMO.
SN 29401270 (C) Copyright 2012 Onkyo Corporation Japan. All rights reserved. C1207-1 2-1, Nisshin-cho , Ney agawa-shi, OSAKA 572-8540, JAP AN T el: 072-831-8023 Fax: 072-831-8163 http://www .onkyo .com/ 18 P ark W a y , Upper Saddle River , N.J. 07458, U .
デバイスOnkyo A-9030の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Onkyo A-9030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo A-9030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo A-9030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo A-9030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo A-9030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo A-9030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo A-9030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo A-9030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
