OnkyoメーカーHT-R640の使用説明書/サービス説明書
ページ先へ移動 of 80
E n A V Receiv er HT -R640 Instruction Manual Thank you for purchasing an Onkyo A V Recei ver . Please read this manual thoroughly before making connections and plugging in the unit. Follo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiver .
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright — Unless it ’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse — The A C fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by quali fi ed service personnel.
5 Features Amplifier • 90 watts per channel into 8 ohms, 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating) • 5-channel ampli fi er • Optimum Gain V olume Circuitry • 24.
6 T ab le of Contents Introduction Important Safety Instructions ..................... 2 Precautions .................................................. 3 Supplied Accessories ................................. 4 Features ...............................
7 Fr ont & Rear P anels The page numbers in parentheses show where you can fi nd the main e xplanation for each item. A ST ANDBY/ON button (37) This button is used to set the A V recei ver to On or Standby .
8 Front & Rear P anels —Continued G Arro w/TUNING/PRESET & ENTER buttons When the AM or FM input source is selected, the TUNING [ ] [ ] buttons are used to tune the tuner , and the PRESET [ ] [ ] buttons are used to select radio presets (see page 49).
9 Front & Rear P anels —Continued The page numbers in parentheses show where you can fi nd the main e xplanation for each item. 1 MUTING indicator (47) This indicator fl ashes while the A V receiv er is muted. 2 HDMI indicator This indicator lights up when the HDMI input is used.
10 Front & Rear P anels —Continued The page numbers in parentheses show where you can fi nd the main e xplanation for each item. A DIGIT AL OPTICAL IN 1, 2, 3 and OUT The optical digital audio inputs can be used to con- nect CD and D VD players, and other components with an optical digital audio output.
11 Front & Rear P anels —Continued O T APE IN/OUT This analog audio input and output are for connect- ing a recorder with an analog audio input and output (cassette, Mini Disc, etc.). P CD IN This analog audio input is for connecting a CD player ’ s analog audio output.
12 Remote Contr oller Notes: • If the remote controller doesn ’ t w ork reliably , try replacing the batteries. • Don ’ t mix ne w and old batteries or dif ferent types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
13 Remote Controller —Continued The remote controller can be used to control different components including the A V receiv er. The remote con- troller has a speci fi c operating mode for use with each type of component. Modes are selected by using the six REMO TE MODE buttons.
14 Remote Controller —Continued For detailed information, see the pages in parentheses. A ST ANDBY/ON button (37) Sets the A V receiv er to On or Standby . B INPUT SELECT OR buttons (45) Used to select the input sources. C MUL TI CH button (46) Selects the multichannel D VD input.
15 Remote Controller —Continued By default, the remote controller is set to control an Onkyo D VD player . A ON/ST ANDBY button Sets the D VD player to On or Standby . B Number buttons Used to enter title, chapter , and track numbers and times for locating speci fi c points.
16 Remote Controller —Continued By default, the remote controller is set to control an Onkyo CD player . A ON/ST ANDBY button Sets the component to On or Standby . B Number buttons Used to enter track numbers and times for locating speci fi c points on CD/MD players.
17 About Home Theater Thanks to the A V receiv er ’ s superb capabilities, you can enjoy surround sound with a real sense of mo vement in your own home — just lik e being in a movie theater or concert hall. W ith D VDs you can enjoy DTS and Dolby Digital.
18 Connecting the A V Receiver • Before making any A V connections, read the manuals supplied with your other A V components. • Don ’ t connect the po wer cord until you ’ v e completed and double-checked all A V connections.
19 Connecting the A V Receiver —Continued Speaker Configuration For the best surround sound e xperience, you should con- nect fi ve speakers and a po wered subwoofer . The following table indicates the channels you should use depending on the number of speakers that you ha ve.
20 Connecting the A V Receiver —Continued Speaker Connection Precautions Read the following before connecting your speak ers: • Only connect speakers with an impedance of 6 ohms or higher .
21 Connecting the A V Receiver —Continued This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiv er won ’ t pick up an y radio signals without any antenna connected, so you must connect the antenna to use the tuner .
22 Connecting the A V Receiver —Continued Connecting an Outdoor FM Antenna If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
23 Connecting the A V Receiver —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiv er, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the A V receiv er.
24 Connecting the A V Receiver —Continued • W ith connection , you can listen to and record audio from your TV . • T o enjoy Dolby Digital and DTS, use connection or .
25 Connecting the A V Receiver —Continued • W ith connection , you can listen to and record audio from a D VD. • T o enjoy Dolby Digital and DTS, use connection or .
26 Connecting the A V Receiver —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as D VD-Audio or SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiv er ’ s multichannel D VD input.
27 Connecting the A V Receiver —Continued W ith this hookup, you can use your VCR ’ s tuner to listen to your fav orite TV programs via the A V receiv er, useful if your TV has no audio outputs. • T o enjoy Dolby Digital and DTS, use connection or .
28 Connecting the A V Receiver —Continued If you hav e two video recorders (e.g., a VCR and a D VD recorder), connect one recorder to the VIDEO 1 OUT jacks, as shown here, and connect the other recorder to the VIDEO 2 OUT jacks in the same way . Notes: • The A V recei ver must be turned on for recording.
29 Connecting the A V Receiver —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fa vorite TV programs via the A V receiv er, useful if your TV has no audio outputs. • W ith connection , you can listen to and record audio from the video source.
30 Connecting the A V Receiver —Continued Connecting a Camcorder , Games Console, or Other De vice Connection A V receiver Signal fl o w Camcorder or console VIDEO 4 INPUT S VIDEO ⇐ S-Video outpu.
31 Connecting the A V Receiver —Continued About HDMI Designed to meet the demands of digital TV , HDMI (High De fi nition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, D VD players, set-top boxes, and other video components.
32 Connecting the A V Receiver —Continued Making HDMI Connections Video Signal Flow Chart Digital video signals received at HDMI IN 1 and 2 are only output by the HDMI OUT and sent to your TV . Composite video, S-V ideo, and component video input sig- nals are not output by the HDMI OUT.
33 Connecting the A V Receiver —Continued ■ CD Play er or T urntable (MM) with Built-in Phono Preamp • W ith connection , you can listen to and record audio from the CD player . • T o connect the CD player digitally , use connection or . (For recording, use and , or and .
34 Connecting the A V Receiver —Continued As of this printing, the Onkyo Remote Interacti ve Dock is the only HDD-compatible component a vailable. ■ For HDD-compatible components that support vide.
35 Connecting the A V Receiver —Continued • W ith connection , you can play and record. • T o connect the recorder digitally for playback, use connections and , or and .
36 Connecting the A V Receiver —Continued W ith (Remote Interactiv e), you can use the follow- ing special functions: ■ A uto P ower On/Standby When you start playback on a component connected via , if the A V receiv er is on Standby , it will automatically turn on and select that component as the input source.
37 T urning On the A V Receiver • Connect the A V receiv er ’ s po wer cord to a suitable wall outlet. Notes: • Befor e connecting the power cord, connect all of y our speakers and A V components. • T urning on the A V receiv er may cause a momentary power sur ge that might interfere with other electrical equipment on the same circuit.
38 Fir st Time Setup The onscreen setup menus are displayed on the connected TV and pro vide a con venient way to change the A V recei ver ’ s settings (The onscreen menus do not appear on a TV that ’ s connected to the HDMI OUT). About the Onscreen Setup Menus Menu ------------------------ 00.
39 First Time Setup —Continued If you connect a component to a digital input jack, you must assign that jack to an input selector . F or example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selec- tor .
40 First Time Setup —Continued HDMI Video Setup If you connect a video component to HDMI IN 1 or 2, you must assign that input to an input selector . F or exam- ple, if you connect your D VD player to HDMI IN 1, you must assign HDMI IN 1 to the D VD input selector .
41 First Time Setup —Continued Component Video Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector . F or example, if you connect your D VD player to COMPONENT IN 3, you should assign it to the D VD input selector .
42 First Time Setup —Continued W ith these settings, you can specify which speakers are connected and a crossov er frequency for each speaker . The following crosso ver frequencies can be speci fi ed: Full Band, 40 Hz, 50 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz, 150 Hz, 200 Hz.
43 First Time Setup —Continued Low-P ass Filter f or the LFE Channel W ith this setting, you can specify the cutoff frequenc y of the LFE channel ’ s lo w-pass fi lter (LPF), which can be used to fi lter out unwanted hum. The LPF only applies to sources that use the LFE channel.
44 First Time Setup —Continued If you connect an -capable Onkyo MiniDisc recorder , CD recorder , or next generation HDD-compat- ible component to the T APE IN/OUT or VIDEO 3 IN jacks, for to work properly , you must change this setting. This setting can only be changed on the A V receiv er.
45 Basic Operations This section explains ho w to select the input source (i.e., the A V component that you want to listen to or watch). Selecting the Input Source 1 3 MUL TI CH MUTING PREVIOUS MENU G.
46 Basic Operations —Continued The multichannel D VD input is for connecting a compo- nent with a 5.1-channel analog audio output, such as a D VD-Audio or SA CD-capable D VD player , or an MPEG decoder .
47 Basic Operations —Continued Y ou can adjust the brightness of the display . Y ou can temporarily mute the output of the A V receiver. W ith the sleep timer , you can set the A V receiv er to turn off automatically after a speci fi ed period.
48 Listening to the Radio W ith the built-in tuner you can enjo y AM and FM radio stations. Y ou can store your fa vorite stations as presets for quick selection. Listening to the Radio T uning into Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears.
49 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM/FM radio stations and XM channels as presets. Selecting Presets Deleting Presets Presetting AM/FM Stations & XM Channels 1 T une into the AM/FM station or XM channel that y ou want to store as a preset.
50 Listening to the Radio —Continued RDS only works with European models and only in areas where RDS broadcasts are av ailable. When tuned into an RDS station, the RDS indicator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals.
51 Listening to the Radio —Continued Displaying Radio T e xt (RT) When tuned to an RDS station that ’ s broadcasting text information, the text can be displayed. Notes: • The message “ W aiting ” may appear while the A V receiv er waits for the R T information.
52 Listening to the Radio —Continued Note: Hardware and required basic monthly subscription sold separately . Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activ ation fee may apply .
53 Listening to the Radio —Continued Setting the Satellite Radio Mode Selecting XM Satellite Radio Signing Up for XM Satellite Radio Before you can use XM Satellite Radio, you must fi rst sign up for an account.
54 Listening to the Radio —Continued Selecting XM Radio Channels There are three ways to select XM radio channels: • Channel Search mode: select an y channel. • Category Search mode: select channels by cate gory . • Direct tuning: enter channel number .
55 Listening to the Radio —Continued Selecting XM Channels from the Fr ont Panel: Selecting the Previous Channel: Displaying XM Radio Inf ormation The following information can be displayed: Note: If the category , artist, or song title is not av ailable, “ - - - ” will be displayed instead.
56 Listening to the Radio —Continued P ositioning the XM P assport System Y ou can check the signal strength of the XM radio signal and adjust the position of the XM Passport System accordingly . XM Radio Messages The following messages may appear while using XM radio.
57 Using the Listening Modes See “ About the Listening Modes ” on page 59 for detailed information about the listening modes. Selecting on the A V Receiver ■ [PURE A UDIO] b utton (not Nor th American models) This button selects the Pure Audio listening mode.
58 Using the Listening Modes —Continued The following table sho ws which listening modes can be used with each input signal format. Source f ormat Listening mode Analog, PCM *1 1. In the Pure Audio and Direct listening modes, 32 kHz, 44.1 kHz, and 48 kHz PCM is processed at 64 kHz, 88.
59 Using the Listening Modes —Continued The A V receiver ’ s listening modes can transform your listening room into a movie theater or concert hall, with high fi delity and stunning surround sound.
60 Using the Listening Modes —Continued Onky o Original DSP Modes Mono Movie This mode is suitable for old movies and other mono sources. The center speak er outputs the sound as it is, while rev erb is applied to the sound output by the other speakers, gi ving presence to ev en mono material.
61 Recor ding This section explains ho w to record the current input source and how to dub audio onto your video recordings. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Y ou cannot record from the D VD analog multichannel input.
62 Ad v anced Operations W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low v olume lev els — ideal for watching movies late at night when you don ’ t w ant to disturb anyone.
63 Ad v anced Setup Speaker Distance Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arri ves at the listener ’ s ears as the sound designer intended. Notes: • The Center and Subwoofer distances can be set up to 5 ft.
64 Adv anced Setup —Continued Speaker Level Calibration Here you can adjust the lev el of each speaker with the built-in test tone so that the v olume of each speaker is the same at the listening position. Note: The speakers cannot be calibrated while the output of the A V receiv er is muted or while a pair of headphones is connected.
65 Adv anced Setup —Continued SW Input Sensitivity Some D VD players output the LFE channel from their subwoofer output at 15 dB higher than normal. Y ou can change the subwoofer sensiti vity to match your D VD player . Note that this setting only af fects signals con- nected to the SUBWOOFER input jack of the multi- channel D VD input.
66 Adv anced Setup —Continued The Audio Adjust functions are explained below . Input Channel Settings ■ Multiplex This setting determines which channel is output from a stereo multiplex source. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.
67 Adv anced Setup —Continued Y ou can assign a default listening mode to each input source that will be selected automatically when you select each input source. For e xample, you can set the default listening mode to be used with Dolby Digital input signals.
68 Adv anced Setup —Continued Y ou can set the input lev el for each input source. This is useful if some of your A V components are louder or qui- eter than others. While this menu is shown onscreen, you can select each input source and set the lev els while listening to and comparing them.
69 Adv anced Setup —Continued Maximum V olume W ith this preference, you can prev ent the volume being set too high by specifying a maximum volume le vel.
70 Adv anced Setup —Continued W ith this preference, you can protect your settings by locking the setup menus. When the setup menus are locked, you cannot change any setting.
71 Adv anced Setup —Continued When using progressiv e scanning on your D VD player , you may fi nd that the picture and sound are out of sync. W ith this setting, you can correct this by delaying the audio signals. Y ou can set it from 0 to 100 milliseconds (ms) in 10 millisecond steps.
72 Contr olling Other Components Y ou can use the A V receiv er ’ s remote controller (RC-651M) to control your other A V components, including those made by other manufacturers. This sec- tion explains ho w to enter the necessary remote control code for the component that you want to control (e.
73 Controlling Other Components —Continued Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example.
74 Controlling Other Components —Continued T o control another component, point the remote contr oller at it and use the buttons explained below . (Y ou must select the appropriate r emote control mode fi rst.) With some A V components, certain buttons may not work as expected, and some may not work at all.
75 Speci fi cations Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs Speci fi cations and features are subject to change without notice.
76 T r oub leshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can ’ t resolv e the issue yourself, contact your Onkyo dealer . Can ’ t turn on the A V receiver • Make sure that the po wer cord is properly plugged into the wall outlet.
77 T roub leshooting —Continued The subwoof er produces no sound • When you play source material that contains no infor- mation in the LFE channel, the subwoofer produces no sound.
78 T roub leshooting —Continued Reception is noisy , FM stereo reception is noisy , or the FM STEREO indicator doesn ’ t appear • Relocate your antenna. • Mov e the A V receiver a way from your TV or com- puter . • Listen to the station in mono (page 48).
79 T roub leshooting —Continued The following settings can be made for the compo- nent video, S-Video, and composite video inputs Y ou must use the buttons on the unit to make these set- tings. 1. While holding down the input selector b utton for the input source that you want to set, press the [SETUP] button.
80 SN 29344250 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.
デバイスOnkyo HT-R640の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Onkyo HT-R640をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo HT-R640の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo HT-R640の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo HT-R640で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo HT-R640を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo HT-R640の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo HT-R640に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo HT-R640デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
