OnkyoメーカーP-3000Rの使用説明書/サービス説明書
ページ先へ移動 of 40
Preamplifier P-3000R Instruction Manual E n.
2 En Introduction Impor tant Safety Instructions 1. Read these ins tructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventila tion opening s.
3 En Precautions 1. Recording Copyright —Unless it’s for personal use only, recording copyrighted ma terial is illegal withou t the permission of the copyright holder. 2. AC Fuse —The AC fuse inside the unit is not use r- serviceable. If you cannot turn on the unit, contact your Onkyo dealer.
4 En For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
5 En Features • DIDRC (Dynamic Intermodulation Distortion Reduction Circuitry) • Separate Digital/Analog Circuitry • Separate Massive Transformers for Digital/Analog Circuitry (Toroidal Transfor.
6 En T echnologies DIDRC (Dynamic Intermodulation Distortion Reduction Circuitry) Since the adv ent of digital audio, the v alues of S/N (signal-to-noise) ratio ha ve risen significantly . Ho we ver , it is also reco gnized that in terms of perceiv ed S/N , analog audio sources are not inferior to digital sources.
7 En Bloc k Diagram DIDRC (Dynamic Intermodulation Distor tion Reduction Circuitry).
8 En Supplied Accessories Make sure you ha ve the follo wing accessories: Remote controller (RC-797S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1) Batteries (R03/AAA ) . . . . . . . . . . . . . . . . . .
9 En Contents Introduction Important Safety Instructio ns ................................................................................. 2 Precautions ......................................... .......................................................
10 En Bef ore Using the Preamplifier Note • If the remot e controller doesn’t work reliably , try replac ing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the re mote controller fo r a long time, remove the batteries to pre v ent damage from leakage or corrosion.
11 En Getting to Kno w the Preamplifier The page numbers in pa rentheses show where you can find the main explanation for each item. a ON/STANDBY button ( ➔ 25 ) Sets the preamplifier to On or Standby. b Standby LED ( ➔ 25 ) Lights when the preamplifier is in Standby mode.
12 En For detailed information , see the pages in parentheses. a PCM indicator Lights when it detects digital audio signal input. It blinks when nothing is detected. b fs indicator ( ➔ 28 ) Lights when sampling rate is displayed. c Message area Displays various information.
13 En a GND screw This screw is for connecti ng a turntable’s ground wire. b PHONO IN L/R jacks These analog audio input s are for connecting a turntable (MM). c CD IN L/R jacks These analog audio input s are for connecting a compact disc play er. d LINE 1/2 IN L/R jacks These analog audio input s are for connecting a playback device.
14 En Remote Contr oller a g b h c e f d c b a For detailed informatio n, se e the pages in parentheses. a 8 button ( ➔ 25 ) Sets the preamplifier to On or Standb y.
15 En Connecti ons Connections Note • Push plugs in all the way to make good connections ( loose connections can cause noise or malfunctions ). • T o prevent interference, keep audio cables away from power cords and speaker cables.
16 En Tip • T o re duce noise, do not tie the signal cable and po wer cable together . Wire them so that they are away from each other . Note • Never disconnect the power cord fr om the preamplifier while the other end is still plugged into a wall outlet.
17 En Connecting a Compact Di sc Play er Analog Connection L R Preamplif ier P-3000R Compact Disc Player C-7000R Digital (Optic al or Coaxial) Connect ion Preamplif ier P-3000R Compact Disc Player C-7000R Connect either of them.
18 En This is an e xample of the connection using the compact disc player C-7000R. Note • Y ou need to change the selector name to use u function ( ➔ 33 ). • Use only u cables for u connections. u ca bles are s upplied with Onk yo Docks. • Connect only On kyo Dock to u jacks.
19 En Remov e the short pins plugged into the ja cks before co nnecting a turntable to the PHONO inputs. Tip • If your turntable (MM) has a phono built-in preamp, you can connect to other analog inputs such as CD IN or LINE 1 IN .
20 En This is an example of the stereo conne ction u sing the power amplifier M-5000R. Connecting a P ower Amplifier Stereo Connecti on Preamplif ier P-3000R Po wer Amplifier M-5000R Right speaker Lef.
21 En This is an example of the bi-amping c onnection using the power amplifier M-5000R. Bi-amping Connection Important: • When making the bi -amping connections, be sure to remo ve the ju mper bars that link the speakers ’ tweeter (high) and woofer (lo w) te rminals.
22 En This is an example of the stereo conne ction u sing the power amplifier M-5000R. Note • If you make a digital audio connection between the preamplifier a nd A V receiver, analog input signal is not output from DIGIT A L OUT .
23 En This is an example of the connect ion using the power amplifier M-5000R. Using Stereo Speaker s as the Fr ont Speaker s for Y our Surround Sound System L R L R Preamplif ier P-3000R Po wer Ampli.
24 En ■ 2.1 channel system (2 speakers and 1 subwoofer) This connection is not a vaila ble for su bwoofers that handl e only mono input . A separate con version cable is required.
25 En Turning On & Basic O perations Basic Operations Tip • After a certain period of warming up, the temperature of the preamplifier’ s components and internal temperature are stabilized, and the sound will soften. • The pre vious input source will appear on the display when the preamplifier turned on.
26 En Note • When the USB connector is not connected, you cannot select USB ev en if you press USB on the remote controller . The message “ NO USB ” appears.
27 En Y ou can adjust the bass , treble and bal ance. Note • The preamplifier will end the setu p if there is no operation for 8 seconds. • The tone controls are canceled when the Direct function is set to on. Adjusting the Bass, T reble and Balance 1 Press SETUP .
28 En When the Direct function is of f, the tone controls can be used to adjust the sound. When the Direct function is on, the tone controls are bypassed, so you can enjoy a pure sound, then front display goe s off and the Direct LED lights.
29 En Note • Always turn do wn the volu me before connecting you r headphones. Settings with SETUP of the remote controller can be also operated with the preampl ifier. Note • The preamplifier will end the setu p if there is no operation for 8 seconds.
30 En Pla ying the Onky o Compact Disc Pla yer The Onkyo compact disc player connected to the preamplifier is played from its remote controller . Note • Make sure the remote controller is pointed a t the compact disc player when using it. • Depending on the component , you may not be able to control with the remote controller .
31 En Pla ying Music Files on the PC This section explains ho w to play music files on a PC through the preamplifier. T o playback the audio data stored on your PC by using the preamplifier via USB port connection, you must install the dri ver on your PC from the Onkyo website.
32 En Controlli ng iPod & Other Components Using an Onky o Doc k Connect an Onkyo Dock to the preamplif ier, and play music files on iPod. Y ou can use the preamplifier’ s remote controller to control basic iPod functions and functionality depends on your iPod model and generation.
33 En Advanced O perations Custom Setup Y ou can switch the selector name to DC/DIG to run as the DOCK selector . ■ To can cel the as signment Press DISPLA Y again for 3 seconds. Note • DOCK can be selected for the Digital input source (COAX1, COAX2, OPT1, OPT2) input selector , but not at the same time.
34 En Y ou can set the volume when using headphones. Y ou can al so use preamplifier’ s MODE and Multi jog dial. See “Using MODE button” to perform this procedure on the preamplif ier ( ➔ 29 ). Note • When using the headphones, the balance settin g will not be applied.
35 En When ASb is turned on, the preamplif ier will automatically enter Standby m ode if there is no operation for 30 minutes with no audio signal input. Y ou can also use preamplifier’ s MODE and Multi jog dial. See “Using MODE button” to perform this procedure on the preamplif ier ( ➔ 29 ).
36 En Others T r oubleshooting If you hav e any trouble using the preamplifier, look for a solution in this section. • Make sure that the power cord is properly plugged into the wall out let ( ➔ 16 ). • Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
37 En • Make sure that the USB cable is plugged in firmly ( ➔ 15 ). • Make sure that the USB driver is installed suc cessfully ( ➔ 31 ). • Make sure that there is no unsupported file formats or signals. • The USB cable is unplugged. To stop the blinking of the display, turn the power ON/ OFF, or plug the USB cable again.
38 En Specifications ■ Audio I nputs ■ Audio O utputs ■ Others ■ System Requirements Specifications and features are subject to change without notice. W indo ws and the W indows logo are trademarks of the Microsoft group of companies. P-3000R THD+N (Total Harmonic Disto rtion+Noise) 0.
39 En Memo.
SN 29400534A Y1102-2 (C) Copyright 2011 ONKY O SOUND & VISION CORPORA TION Japan. All rights reser ved. * 2 9 4 0 0 5 3 4 A * 2-1, Nisshin-cho , Ney agaw a-shi, OSAKA 572-8540, JAP AN T el: 072-831-8023 F ax: 072-831-8163 http://www .onkyo .com/ 18 P ark Wa y , Upper Saddle River , N.
デバイスOnkyo P-3000Rの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Onkyo P-3000Rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo P-3000Rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo P-3000Rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo P-3000Rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo P-3000Rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo P-3000Rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo P-3000Rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo P-3000Rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。