OnkyoメーカーTX-NR3007の使用説明書/サービス説明書
ページ先へ移動 of 164
E n A V Receiv er TX-NR3007 TX-NR5007 Instruction Manual Thank you for purchasing an Onkyo A V Receiv er. Please read this manual thoroughl y before making connections and plugg ing in the unit. Follo wing the inst ructions in this manual will enable you to obtain opti mum performance and listening enjoyment from your new A V Receiv er.
2 Impor tant Safety Instructions 1. Read these ins tructions. 2. Ke ep these instructi ons. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near w ater . 6. Clean only with dry cloth. 7. Do not block an y ventil ation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyright ed material is il legal wit h- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by qualified service personnel.
5 Contents Important Safety Instructions .......................... .................. 2 Precautions ............................................. .......................... 3 Supplied Accessories ............................. ........................
6 Features Amplifier (TX-NR3007) • 140 W atts/Channel @ 8 ohms (FTC) • 200 W atts/Channel @ 6 ohms (IEC) • 250 W atts/Channel @ 6 ohms (JEIT A) (TX-NR5007) • 145 W atts/Channel @ 8 ohms (FTC) .
7 Features —Continued *6. HD Radio™ an d the HD Radi o Ready logo are propriet ary trademarks of iBiquity Di gital Corpor ation. T o recei ve HD Radio bro adcasts, you mu st install an Onkyo UP-HT1 HD Radio tun er module (sold separa tely). *7. In Europe, using banan a plugs to con nect speakers to an audio amplifie r is prohibited.
8 Fr ont & Rear P anels The actual front panel has v arious logos printe d on it. They are not sho wn here for clarity . The page numbers in parentheses show where you can f ind the main explanation for each item. a ON/ST A NDBY button (48) This button is used to set the A V receiver to On or Standby .
9 Fr ont & Rear P anels —Continued (Nor th American models) (Eur opean and Asi an models) The page numbers in parentheses show where you can find the main explanation for each item. j PHONES jack (70) This 1/4-inch phone jack is for connecting a stan- dard pair of stereo hea dphones for priv ate listening.
10 Front & Rear P a nels —Continued v SETUP MIC jack (62) Audyssey MultEQ ® XT Room Correction and Speaker Setup micropho ne connects here. w USB port (127 ) A USB mass storage device, such as a USB flash driv e or MP3 player , containing music files can be plugged in here and the music selected can be played through the A V receiv er.
11 Fr ont & Rear P anels —Continued g T uning indi cators RDS (European models) (75): Lights when tuned to a radio station that supports RDS (Radio Data System). AU T O ( 7 3 ) : Lights when Auto T uning m ode is selected for AM or FM radio. Goes off when Manual T uning mode is selected.
12 Front & Rear P a nels —Continued d DIGIT AL COAXIAL IN 1, 2, and 3 These coaxial digital audio inputs are for connect- ing components with coaxia l digital audio outputs, such as CD and D VD/BD players. The y’ re assign- able, which means you can assign each one to an input selector to suit your setup.
13 Fr ont & Rear P anels —Continued y D VD/BD IN Here you can connect a D VD/BD player . Input jacks include S-V ideo, co mposite video, and analog audio.
14 Remote Contr oller Notes: • If the remote controller doesn’ t work reliably , try replacing the batteries. • Don’t mix new and old batteries or dif ferent types of batteries. • If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.
15 Remote Controller —Contin ued For detailed information, se e the pages in parentheses. a ST ANDBY button (48) Sets the A V receiv er to Standb y . b ON button (48) T urns on the A V rece iv er. c A CTIVITIES b uttons (71, 153) Used with the MA CR O function.
16 Remote Contr oller —Continued ■ Controlling the tuner T o control the A V receiver’ s tuner, press the [TUNER] (or [RECEIVER]) button. Y ou can select AM or FM by pressing the [TUNER] b ut- ton repeatedly . 1 Arr ow [ q ]/[ w ] buttons Used to tune into radio stations.
17 About Home Theater Thanks to the A V receiver’ s superb capabilit ies, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie th eater or concert hall. W ith DVDs you can enjo y DTS and Dolby Digital.
18 Connecting the A V receiver About Speaker s A and Speakers B Speakers A and Speakers B allo ws you to hav e two speaker c onf igurations of up to 7.2 spea k ers. Each configuration has its own pair of stereo front speakers and can use the same subwoofer , center, sur round, and surround back speakers, as required.
19 Connecting the A V receiver —Continued Speaker Config uration For 9.2-channel surround-sound playback, you need nine speak ers and two powered subwoo fers. The following table indicates the ch annels you should use de pending on the number of speakers that you have .
20 Connecting the A V receiver —Contin ued Using Dipole Speak ers Y ou can use dipole speak ers for the surround left and right, surround back left and right speake rs. Dipole speakers output the same sound in two directions. Dipole speakers typically ha ve an arro w printed on them to indicate ho w they shoul d be positioned.
21 Connecting the A V receiver —Continued Connecting the Spea ker Cables ■ 9.2-channel Playbac k with Speakers A The following illustration shows which speaker should be connec ted to each pair of terminal s. If you’ re using only one surround back speaker , connect it to the SURR B A CK/ZONE 3 L terminal.
22 Connecting the A V receiver —Contin ued ■ 7.2-channel Pla yback with Speakers A or Speakers B The following illustration sh ows which speak er should be connected to each pair of terminals for up to 7.2-channel playback with Speakers A or Speakers B.
23 Connecting the A V receiver —Continued The FR ONT L/R and SURR B A CK/ZONE 3 L/R termi- nal posts can be used with front speakers and surround back speakers respecti vely , or bi-amped to provide sepa- rate tweeter and woofer feeds for a pair of front speak ers A that support bi-amping, pr oviding impro ved bass and treble performance.
24 Connecting the A V receiver —Contin ued The FR ONT L/R and SURR BA CK/ZONE 3 L/R ter- minal posts can be used with front speakers and surround back speakers resp ectiv ely , or bridged together to pro- vide almost double the out put power for the front speakers A.
25 Connecting the A V receiver —Continued The FR ONT WIDE/ZONE 2 L/R and SURR B A CK/ZONE 3 L/R terminal posts can be used with front wide speakers and su rround back speakers respec- tiv ely , or b.
26 Connecting the A V receiver —Contin ued The FR ONT WIDE/ZONE 2 L/R and SURR B A CK/ZONE 3 L/R terminal pos ts can be used with front wide speake rs and surro und back speak ers respec- ti vely , or bridged together to provide almost dou ble the output power for the front speak ers B.
27 Connecting the A V receiver —Continued This section explains ho w to connect the supplied indoor FM antenna and AM loop ante nna, and how to connect commercially a v ailable outdoor FM and AM an tennas. The A V receiv er won’ t pick up any radio signals without any an tenna connected, so you must connect the antenna to use the tuner .
28 Connecting the A V receiver —Contin ued Connecting an Outdoo r FM Antenna If you cannot achie ve good reception with the supplied indoor FM antenna, try a co mmercially a vailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obta i ned when installed in an attic or loft.
29 Connecting the A V receiver —Continued • Before making any A V conne ctions, read the manuals supplied with your other A V components. • Don’t connect the power cord until you’ ve completed and double-checked all A V connections.
30 Connecting the A V receiver —Contin ued About HDMI Designed to meet the increased demands of digital TV , HDMI (High Definition Mu ltimedia Interface) is a new digital interface standard for connect ing TVs, projectors, D VD/BD players, set-top boxes, and other video components.
31 Connecting the A V receiver —Continued Making HDMI Connections ■ Video Signals Digital video signals recei ved b y th e HDMI IN jacks are norma lly output by the HDMI MAIN OUT and SUB OUT for display on your TV . Composite vi deo, S-V ideo, and component video sou rces can be upcon verted for the HDMI output.
32 Connecting the A V receiver —Contin ued By connecting both the audio and video out puts of your D VD/BD player and other A V components to the A V receiv er, you can select both the audio a nd video simultaneously simply by selecting the appropriate input source on the A V receiv er.
33 Connecting the A V receiver —Continued ■ “Monitor Out” Setting Set to “Both”, “Both(Main)” or “Both(Sub)” W ith the “Monitor Out” setting set to “Both”, “Both(Main)”.
34 Connecting the A V receiver —Contin ued A udio Connection Formats Audio equipment can be connected to the A V receiv er by using an y of the follo wing audio con- nection formats: analog, optical, coaxial, analog multichannel, or HDMI.
35 Connecting the A V receiver —Continued See “Connecti ng Components with HDMI” on page 30 f or HD MI connection information. • With connection , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3. • T o enjoy Dolby Digital and DTS, use connection or .
36 Connecting the A V receiver —Contin ued See “Connecting Components with HDMI” on page 30 for HDMI connection inf ormation. • With connection , you can listen to and record audio from your D VD player or listen in Zone 2 or Zone 3. • T o enjo y Dolby Digital and DTS, use connection or .
37 Connecting the A V receiver —Continued Hooking Up the Multichannel Inp ut If your D VD player supports multichannel audio formats such as D VD- Audio a nd Sup er Audio CD, and it has a multi- channel analog audio output, you can connect it to the A V recei ver’ s multichannel input.
38 Connecting the A V receiver —Contin ued W ith this hookup, you can use your VCR’ s tuner to li sten to your f av orite TV programs via the A V receiv er, useful if your TV has no audio outputs. • With connection , you can listen to the V CR or D VD recor der in Zone 2 or Zone 3.
39 Connecting the A V receiver —Continued Notes: • The A V receiver must be turned on for recording. Recordi ng is not possible while it’ s in Standby mode.
40 Connecting the A V receiver —Contin ued W ith this hookup, you can use your sa tellite or cable recei v er to listen to your fa vorite TV programs via the A V receiv er, useful if your TV has no audio outputs. • With connection , you can listen to and record audio from the video sour ce or listen in Zone 2 o r Zone 3.
41 Connecting the A V receiver —Continued • With connection , you can listen to and record audi o from your game console or listen in Zone 2 or Zone 3. • T o en joy Dolby Digital and DTS, us e connection . (T o record or listen in Zone 2 or Zone 3 as well, use and .
42 Connecting the A V receiver —Contin ued Connecting a Camcor der or Other De vice Connection A V receiver Signal flow Camcorder etc. A UX1 INPUT VIDEO ⇐ Composite video output A UX1 INPUT L-A UDIO-R ⇐ Analog audio L/R output A UX1 INPUT DIGIT AL ⇐ Digital optical output Step 1: Video Connection Make the connection .
43 Connecting the A V receiver —Continued ■ CD Player or T urntable (M M) with Built-in Phono Preamp • With connection , you can listen to and record audi o from your CD player or listen in Zone 2 or Zone 3. • T o connect the CD player digitally , use connection or .
44 Connecting the A V receiver —Contin ued • With connection , you can play and record or li sten in Zo ne 2 or Zone 3. • T o connect th e recorder dig itally for playback, use conne ctions and , or and .
45 Connecting the A V receiver —Continued If you want to use a more po werful powe r amplif ier and use the A V receiv er as a preamp, connect it to the PRE OUT jacks, and connect all speakers and the subwoofer to the po wer amplifier . Y ou can connec t the po wered subwoofer with each jacks respecti vely .
46 Connecting the A V receiver —Contin ued ■ If Y our iP od Suppor ts Vide o: Connect your RI Dock’ s audio output jacks to the A V receiv er’ s GAME IN or VCR/D VR IN L/R jacks, and connect its video output ja ck to the A V receiv er’ s GAME IN V or VCR/DVR IN V jack.
47 Connecting the A V receiver —Continued Wi t h u (Remote Interactiv e), you can use the follow- ing special functions: ■ Auto P ower On/Standby When you start playback on a component connected via u , if the A V recei ver is on Standb y , it will auto- matically turn on and select that component as the input source.
48 T urning On the A V receiver Eur opean and Asia n models : T o completely shut do wn the A V recei ver, set the [PO WER] switc h to the OFF position () .
49 Fir st Time Setup This section explains the settings that you need to make before using the A V recei v er for the very f irst time. If you connect your TV to HDMI OUT MAIN, “Monitor Out” setti.
50 First Time Setup —Contin ued In this Instruction Manual, illustratio ns from the onscreen menu or e xplanations referring to the menu will be in the same language as the Instruction Manua l. The default Language setting for th e onscreen menu is English.
51 First Time Setup —Continued Carry out the settings for th e A V recei ver b y using t he Onscreen Setup Menu. The settings of the A V recei v er can be changed using the Display . Onscreen Setup Menus an d Displa y As each item in the Onscreen Setup Menus is selected, the select ed items will be displayed one by one.
52 First Time Setup —Contin ued If you connect your TV to the HDMI output, set the “Monitor Out” setting so that the onscreen setup menus are displayed and composit e video, S-V ideo, and component video sources are upcon v erted and output.
53 First Time Setup —Continued Notes: • See page 32 for charts showing how the “Monitor Out” and “Resolution” settings af fect the video signal flo w through the A V recei ver. • This procedure can also be performed on the A V recei ver by using its [SET UP] butto n, arrow b uttons, and [ENTER] button.
54 First Time Setup —Contin ued HDMI Input Setup If you connect a video component to HDMI IN, you must assign that input to an input selector . F or example, if you connect your D VD/BD player to HDMI IN 1, you must assign HDMI IN 1 to th e D VD/BD input selector .
55 First Time Setup —Continued Component Video Input Se tup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector . For example, if you connect your D VD/BD player to COMPONENT VIDEO IN 2, you should assign it to the DVD/BD input selector .
56 First Time Setup —Contin ued If you connect a component to a digital input jack, you must assign t hat jack to an in put selector . For e xample, if you connect your CD player to the OPTICAL IN1 jack, you should assign that jack to the CD input selector .
57 First Time Setup —Continued If you connect a component to the A V recei ver’ s analog multichannel input, you must assign that input to an input selector . For example, if you connect your D VD/ BD player to the MUL T I CH input, you must assign it to the D VD/BD input selector .
58 First Time Setup —Contin ued P owe red Zone 2/3 See “Setting the Powere d Zone 2/3” on page 134. Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button. 2 Use the Up and Down [ q ]/[ w ] but- tons to select “2.
59 First Time Setup —Continued For the onscreen setup menus to display properly , you must specify the TV syste m used in your area. Note: This procedure can also be performed on the A V recei ver by using its [SETUP] bu tton, arrow b uttons, and [ENTER] button.
60 First Time Setup —Contin ued Note: This procedure can also be performed on the A V receiver by using its [SETUP] b u tton, arro w buttons, and [ENTER] button.
61 First Time Setup —Continued W ith the supplied calibrated microphone, Audyssey MultEQ XT automatica lly determines the number of speakers connected, their size for purposes of bass management, optimum cr ossov er frequencies to the subwoofer (if present), and di stances from the primary listening position.
62 First Time Setup —Contin ued Using A udysse y MultEQ ® XT ENTER ON/ST ANDBY qwer Speaker setup microphone Notes: • If any of your speakers is 4 ohms, change “Speaker Impedance” se tting before runnin g Audyssey MultEQ X T Room Correction and Speaker Setup (see page 57).
63 First Time Setup —Continued • Make the room as quiet as possible. Background noise can disrupt the room measurement s. Close windows, silence cell phones, televisions, radios , air conditioners, fluorescent lights, home appliances, light dimmers, or other devices.
64 First Time Setup —Contin ued Notes: • When the room correction and speaker setup is complete, the “Equalizer Settings” (page 98) will be set to “Audyssey” and “Dyna mic EQ” (page 102) will be set to “On”.
65 First Time Setup —Continued One of the front speak ers has not been detected. One of the front wide speakers has not been detected. One of the front high speakers has not been detected . One of the surround speakers has not been detected. The surround back speakers ha ve been detected but the surround speakers ha ven’ t.
66 First Time Setup —Contin ued The speaker type detected does not match what was expected. The speak er may be incorrect type or bro- ken. Please check that it is t he correct speak er type.
67 Basic Operations This section explains ho w to select th e input source (i.e., the A V component that you want to listen to or w atch). Selecting the Input Sour ce 1 Use the A V re ceiver’ s input select or buttons to se lect the input source.
68 Basic Oper ations —Continued Y ou can adjust the bass and treble for the front speakers, except when the Direct, Pu re Audio or THX listening mode is selected. ■ Bass Y ou can boost or cut lo w-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.
69 Basic Operations —Continued Y ou can adjust the brightness of the A V recei ver’ s dis- play . Y ou can temporarily mute th e output of the A V recei ver. Tip: Y ou can specify ho w much the output is muted with the “Muting Lev el” setting (page 110).
70 Basic Oper ations —Continued Front High or Front Wide Speaker s When “Speakers T ype(FrontB) ” setting is set to “Not Use”, you can select the priority of the use of Front High or Front W ide speakers. Notes: • Front High or Front W ide speakers cannot b e selected in either of the following cases: 1.
71 Basic Operations —Continued Using the Ea sy macro comm and in the Ea sy macro mode, you can sequentially operate Onk yo components with simple com mands by simply pressing one b utton. These commands are user-spe cif iable (see page 150) and the default actions are described belo w .
72 Basic Oper ations —Continued Changing Sour ce Component When you want to operate th e component that is not assigned as the source component, you can assign it as the source component.
73 Listening to the Radio W ith the built-in tuner you can enjoy AM and FM radio stations. Y ou can st ore your fav orite stations as presets for quick selectio n. Listening to the Radio T uning into Rad io Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears.
74 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fa vorite AM/FM radio stations as presets. Note: Y ou can name your radio presets for easy identif ication (see page 105). Its name is di splayed instead of the band and frequency .
75 Listening to the Radio —Continued RDS only works in ar eas where RDS br oadcasts are ava i la b le . When tuned into an RDS st ation, the RDS indicator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radi o signals.
76 Listening to the Radio —Continued When tuned to an RDS station that’ s broadcasti ng te xt information, the text can be displayed. Display ing Radio T ext (RT) Notes: • The message “ W aiting ” may appear while the A V receiv er waits for the R T information .
77 Univer sal P or t Option UP-A1 Dock f or iP od W ith the UP-A1 Dock (sold separately), you can easily play the music, photo, or movie stored on your Apple iPod through the A V receiver and enjoy great sound. Y ou can use the A V recei ver’ s remote controller to operate your iPod.
78 Universal P or t Option UP-A1 Dock f or iP od —Contin ued By pressing the REMO TE MODE button that’ s been programmed with the remote contr ol code for your Dock, you can control your iPod in the Dock with the follow ing buttons.
79 Universal P or t Option UP-A1 Dock f or iP od —Contin ued Status messa ges ❏ PORT Reading The A V receiv er is checking the connection with the dock. ❏ PORT Not Support The A V receiv er do not support the connected dock. ❏ PORT UP-A1 UP-A1 Dock is connected.
80 Recor ding This section explains ho w to record t he selected input source to a component with recording capability , and how to r ecord audio and video from dif ferent sources. Notes: • The surround sound and DSP listening modes cannot be recorded.
81 Using the Listening Modes See “ About the Listening Modes” on page 89 for detailed information a bout the listening modes. Selecting on th e A V receiver ■ [PURE A UDIO] button This button selects the Pu re Audio listening mode.
82 Using the Listening Modes —Continued Mono/Multiplex Sour ces ✔ : A vailable Listening Modes Notes: *1 For 7ch output, out put can be swi tched betwe en Front high or Front wide spe akers by pressing t he [SP LA YOUT] button (dependi ng on the “Speaker Configuration” setting (see page 95)).
83 Using the Listening Modes —Continued Stereo Sour ce (1/2) ✔ : A vail able Li stening Modes Listening Mo de B utton Speaker lay out Pure Audio *5 ✔✔✔✔ Direct ✔✔✔✔ Stereo ✔✔.
84 Using the Listening Modes —Continued Stereo Source (2/2) ✔ : A vailable Listening Modes Notes: *1 For 7ch output, out put can be swi tched betwe en Front high or Front wide spe akers by pressing t he [SP LA YOUT] button (dependi ng on the “Speaker Configuration” setting (see page 95)).
85 Using the Listening Modes —Continued 5.1 chan nel Sourc es (1/3) ✔ : A vail able Li stening Modes Listening Mo de B utton Speaker lay out Pure Audio *5 ✔✔✔✔ Direct ✔✔✔✔ Stereo .
86 Using the Listening Modes —Continued 5.1 channel Sour ces (2/3 ) ✔ : A vailable Listening Modes Listening Mode Button Speaker lay out PLIIx Music THX Music ✔ PLIIx Music Au dy s s ey D S X .
87 Using the Listening Modes —Continued 5.1 chan nel Sourc es (3/3) ✔ : A vail able Li stening Modes Notes: *1 For 7c h output, output can b e switched be tween Front h igh or Front wide speakers by pre ssing the [SP LA YOUT] button (dependin g on the “Speak er Conf iguration” settin g (see page 95)) .
88 Using the Listening Modes —Continued 7.1 channe l Source s ✔ : A vailable Listening Modes Listening Mode Button Speaker lay out Pure A udio* 5 ✔✔✔✔ Direct ✔✔✔✔ Stereo ✔✔✔.
89 Using the Listening Modes —Continued Notes: *1 For 7c h output, output can b e switched be tween Front h igh or Front wide speakers by pre ssing the [SP LA YOUT] button (dependin g on the “Speak er Conf iguration” settin g (see page 95)) .
90 Using the Listening Modes —Continued 5.1-channel sour ce + Dolby EX These modes expand 5.1-channel sources for 6.1/7.1- channel playback. They’ re espe cially suited to Dolby EX soundtracks that include a matrix-encoded surround back channel.
91 Using the Listening Modes —Continued THX Founded b y George Lucas, T HX de velops stringent stan- dards that ensure movies are reproduced in movie the- aters and home theaters just as the director intended. THX Modes carefully optim ize the tonal and spa tial characteristics of the soundt rack for reproduction in the home-theater en vironment.
92 Adv a nced Setup The onscreen setup menus appear on the connected TV and pr ovide a con venient w ay to change the A V recei ver’ s var ious settings. Se ttings are or ganized into nine categories on the main menu , most containing a submenu . Onscreen Setup Menus 1.
93 Adv anced Setup —Contin ued This section explains items on the “Input/Output Assign” menu. Note: This procedure can also be performed on the A V recei ver by using its [SETUP] bu tton, arrow b uttons, and [ENTER] button. Input/Output Assign 1 Press the [RECEIVER] button f ollowed by the [SETUP] b utton.
94 Adv anced Setup —Continued Component Video Input See “Component V ideo I nput Setup” on page 55. Digital A udio Inp ut See “Digital Audio Input Setup” on page 56. Analog A udio Input Multich See “ Analog Audio Input Setup” on page 57.
95 Adv anced Setup —Contin ued Some of the settings in this sectio n are set automatically b y Audyssey MultEQ ® XT Room Correction and Speak er Setup (see page 61).
96 Adv anced Setup —Continued Surr Back Ch *8 1ch: Select if only one surround back L speaker is connected. 2ch: Select if two (left and right) surround back speakers are connected (def ault).
97 Adv anced Setup —Contin ued Speaker Distance This setting is set automati cally by Audyssey M ultEQ ® XT Room Correction and Sp eaker Setup (see page 61). Here you can specify the distance from each speaker to the listening position so that the sound from each speak er arri ves at the listener’ s ears as the sound designer intended.
98 Adv anced Setup —Continued Equalizer Settings This setting is set automatically b y Audyssey MultEQ ® XT Room Correction and Speaker Setup (see page 61). W ith the Equalizer settings, you can adjust the tone of speakers indi vidually wi th a 7-band equalizer .
99 Adv anced Setup —Contin ued THX Audio Setup This setti ng is not set automatical ly by Audyssey MultEQ ® XT Room Correction and Speaker Setup (see page 61). W ith the “SurrBack Sp Spacing” setti ng, you can specify the distance betw een your surround back speakers.
100 Adv anced Setup —Continued W ith the Audio Adjust functions and settings, you can adjust the sound and li stening modes as you like. Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button.
101 Adv anced Setup —Contin ued Center Width 0 to 7 (default: 3) W ith this setting, you can adjust the width of the sound from the center speak er when using the Dolby Pro Logic IIx Music listening mode. Normally , if you’ re using a cent er speaker , the center chann el sound is output by only the center speaker .
102 Adv anced Setup —Continued Au dy s se y For “Dynamic EQ”, “R eference Lev el” and “Dynamic V olume”, you cannot chan ge the settings before completing Audyssey MultEQ ® XT Room Correction and Speaker Setup. Au dysse y settings cannot be adjusted while Speakers B is selected.
103 Adv anced Setup —Contin ued Theater-Dimensio nal Listening Angle Wide : Select if the listening angle is greater than 30 de grees (default). Narrow: Select if the li stening angl e is less than 30 degrees.
104 Adv anced Setup —Continued This section explains items on the “Source Setup” me nu. Items can be set indi vidua lly for each input sele ctor . Note: This procedure can also be perform ed on the A V recei ver by using its input selector buttons, [SET UP] button, arrow b uttons, and [ENTER] button.
105 Adv anced Setup —Contin ued Name Edit Y ou can enter a custom name for each individual input selector (e xcluding TUNER) and radi o preset for easy identi- fication.
106 Adv anced Setup —Continued Zoom Mode This setting determine s the aspect ratio. Normal: Full: (default) Zoom: Wide Z oo m:.
107 Adv anced Setup —Contin ued ISF Mode Custom: User setting (All items can be fre ely set.) Day: Setting when a room is bright. Night: Setting when a room is d ark. The receiv er has been designed to incorporate setup a nd calibration standards esta blished by the Imaging Sci- ence F oundation (ISF).
108 Adv anced Setup —Continued Resolution *2 Through: Select this to pass video through the A V receiv er at the same resolution and with no con version (default). Au t o : Select this to hav e the A V recei ver automatica lly con vert vide o at resolutions not supported b y your TV .
109 Adv anced Setup —Contin ued Y ou can assign a def ault listening mode to each input source that will be selected automati cally when you select each input source. For e xample, you can set the default listening mode to be used wi th Dolby Digital in put signals.
110 Adv anced Setup —Continued This section explains the item s on t he “Miscellaneous” menu. Note: This procedure can also be perform ed on the A V recei ver by using its [SETUP] b utton, arro w buttons, and [ENTER] button. Miscellaneous (V olume/OSD) Setup 1 Press the [RECEIVER] button f ollowed b y the [SETUP] button.
111 Adv anced Setup —Contin ued . This section explains items on the “Hardw are Setup” menu. Note: This procedure can also be performed on the A V recei ver by using its [SETUP] bu tton, arrow b uttons, and [ENTER] button. OSD Setup Immediate Display On: Displayed (def ault).
112 Adv anced Setup —Continued Remote ID Remote ID 1, 2, 3 When sev eral Onkyo components are used in the same r oom, their remote ID co des may ov erlap. T o differ en- tiate the A V receiv er from the other components, you can change its remote ID from 1, the default, to 2 or 3.
113 Adv anced Setup —Contin ued HDMI A udio TV Out Off : HDMI audio is not output to TV (default). On: HDMI audio is output to TV and the sound will be heard from the TV speakers. This preference determines whether audio receiv ed at the HDMI i nput is output from the HDMI outputs.
114 Adv anced Setup —Continued HDMI Control (RIHD) O n: en abled. Off: disabled (default). This function allows -compatibl e components connected via HDMI to be controlled with the A V receiver. Notes: • , which stands for Remote Interactive o ver HDMI, is the name of the system control function found on Onkyo components.
115 Adv anced Setup —Contin ued Network See “Network Settings” on page 126. Firmware Update Notes: • Perform the firmware update only when an announcement is posted on the Onk yo W eb site. • It takes about 60 minutes to complete the firmwa re update.
116 Adv anced Setup —Continued W ith this preference, you ca n protect your settings b y locking the setup menus. Note: This procedure can also be performed on the A V receiver by using its [SETUP] b u tton, arro w buttons, and [ENTER] button.
117 Adv anced Setup —Contin ued Y ou can change v arious audio settings by pressing the [A UDIO] button. Note: When the “Audio TV Out ” setting is set to “On” (page 113), the [A UDIO] b utton is disabled. Using the A udio Settings A UDIO RECEIVER qwer 1 Press the [RECEIVER] button f ollowed b y the [A UDIO] b utton.
118 Adv anced Setup —Continued Re-EQ Function W ith the Re-EQ function, you can compensate a soundtrack whose high-frequency con tent is too harsh, making it more suitable for home theater vie wing. Re- EQ Off: Re-EQ Fun ction off (default). On: Re-EQ Function on.
119 Adv anced Setup —Contin ued Speaker Levels Y ou can adjust the v olume of each spea ker while listening to an input source. These temporary adjustments are cancelled when the A V receiv er is set to Standby . T o sav e the setting you made here, go to “Lev el Calibration” on page 97 before setting the A V receiv er to Standby .
120 NET/USB The A V recei ver is network-r e ady , which means you can hook it up to your home network with a standard Ether- net cable and enjoy the music files stored on your com- puter or media server . If your network is connected to the Internet, you can also enjo y Internet radio.
121 NET/USB —Continued T o receiv e Internet radio, you must connect the A V receiver to a netw ork with Internet access (page 120). Y ou can select Internet radi o stations b y connecting to the A V receiv er from your co mputer and selecting sta- tions in your W eb bro wser .
122 NET/USB —Continued This section explains ho w to play music f iles on a com- puter or media server through the A V receiver. See pages 124 to 125 for details on supported music servers and music file formats. For W indo ws Media Player 11, see “W indows Media Player 11 Setup” on page 123.
123 NET/USB —Continued Random Playback The Random function can only be set while the PLA Y screen is displayed. T o play songs in random order, during playback (or while playback is paused or stopped), press the [RAN- DOM] b utton. All of the songs in the current folder wil l be played in random order .
124 NET/USB —Continued Supported Audio File Formats For serv er playback, the A V receiver supports the fol- lowing music file formats: MP3, WMA, W A V , FLA C, Ogg V orbis, AAC and LPCM. ■ MP3 • MP3 files must be MPEG -1/MPEG-2 Audio Layer 3 format with a sampling ra te of 8 kHz, 11.
125 NET/USB —Continued Server Requirements The A V receiv er can play digi tal music files stored on a computer or media server and supports the follo wing technologies: • Windo ws Media Player 11 • Windo ws Media Connect 2.
126 NET/USB —Continued Note: When modifying netw ork settings, after modifying it is necessary to ex ecute “Sa ve”. This section explains ho w to conf igure the A V receiver ’ s network settings manually .
127 NET/USB —Continued Mac Address This is the A V recei ver’ s MA C (Media Access Control) address. This addres s cannot be changed. DHCP This setting determines whet her or not the A V receiver uses DHCP to automatical ly config ure its IP Address, Subnet Mask, Gate way , and DNS Server settings.
128 NET/USB —Continued This section explains ho w to play music f iles on a USB mass storage device. Playin g Music Files on a USB Device 1 Plug your USB mass storage devi ce into the A V receiver’ s USB por t. 2 (TX-NR3007) Press the [NET/USB] button repeatedly to select the USB screen.
129 NET/USB —Continued Random Playback The Random function can only be set while the PLA Y screen is displayed. T o play songs in random order , while the list of songs is displayed, press the [RANDOM] button. All of the songs in the current folder will be played in random order .
130 Multi Zone Y ou can use three speaker systems with this A V recei ver — Main r oom: a surround-sound speak er system (up to 9.2 channels) for enjoying D VD mo vies in your main room, Speak ers B.
131 Multi Zone —Continued In addition to your main listening room, you can also enjoy pl ayback in the other room, or as we call Multi Zone. And, you can select a different source for each room. There are two ways you can connect Zone 2 speakers: 1.
132 Multi Zone —Continued Zone 2 Video Outpu t The A V receiv er features a composite video output for connection to a TV in Zone 2, so you can enjo y both audio and video in that zone. Hookup • Use a composite video cable to connect the A V receiv er’ s ZONE 2 OUT V ja ck to a composite video input on your Zone 2 TV .
133 Multi Zone —Continued There are two ways you can connect Zone 3 speakers: 1. Connect them directly to the A V receiv er. 2. Connect them to an amp in Zone 3.
134 Multi Zone —Continued If you’ v e connected your Zone 2/3 speakers to the A V receiv er, as explained in “Connecting Y our Zone 2 Speakers Directly to the A V receiv er” on page 131 or “.
135 Multi Zone —Continued Note: This procedure can also be performed on the A V recei ver by using its [SETUP] bu tton, arrow b uttons, and [ENTER] button.
136 Multi Zone —Continued This section explains ho w to turn Zone 2/3 on and of f, how to selec t an input sour ce for Zone 2/3, and ho w to adjust the v olume for Zone 2/3. Contro lling Zone 2/3 fr om the A V rec eiver Note: When Zone 2/3 is turned off, the output from the 12V TRIGGER OUT ZONE 2/3 goes low (0 volts).
137 Multi Zone —Continued Notes: • Only analog input sources are output by the ZONE 2/ 3 PRE OUT and ZONE 2/3 L/R speaker terminals. Digital input sources are not output. If no sound is heard when an input source is select ed, check if it’ s connected to an analog input.
138 Multi Zone —Continued T o control the A V rec eiv er with the remote controll er while you’ re in Zone 2 or Zo ne 3, you’ll need a commer- cially a va ilable multiroom remot e control kit for e ach zone. • Multiroom kits are made b y Niles and Xantech.
139 Contr olling Other Components Y ou can use the A V recei ver’ s remote control ler (RC-747M) to control your other A V components, including those made by ot her manufacturers. This sec- tion explains ho w to enter th e remote control c ode for a component that you want to control: D VD, TV , VCR, etc.
140 Controlling Other Components —Contin ued 5 Use the Up and Down [ q ]/[ w ] but- tons to select category , and then press [ENTER]. The brand name input panel appears. 6 Use the arro w [ q ]/[ w ]/[ e ]/[ r ] but- tons to select a character , and then press [ENTER].
141 Contr olling Other Components —Continued Y ou’ ll need to enter a code for each component that you want to control. Note: The remote control codes provided are correct at t he time of printing, but are subject to change.
142 Controlling Other Components —Contin ued Onkyo components that are connected via u are con- trolled by pointing the remo te controll er at the A V receiv er, not the component. Th is allo ws you to control components that are out of vie w , in a rack, for example.
143 Contr olling Other Components —Continued By pressing the [TV] button that’ s been programmed with the remote control code for TV , you can control your TV with the following b uttons. For details on entering a remote control code for a differ- ent component, see page 141.
144 Controlling Other Components —Contin ued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your D VD player (HD D VD, Blu-ray , or TV/D VD combination), you can control your player w ith the follo wing bu ttons.
145 Contr olling Other Components —Continued t PLA Y MODE b utton* Selects play modes on components with selectable play modes. u CLR button Cancels functions and cl ears entered numbers. Notes: • With some components, certain b uttons may not work as expected, and some may not work at all.
146 Controlling Other Components —Contin ued By pressing the REMO TE MODE button that’ s been programmed with the remote control code fo r your sat- ellite receiver , cable receiver , or D VD recorder (DBS/ PVR combination or cable/ PVR combination), you can control your player with the follo wing buttons.
147 Contr olling Other Components —Continued By pressing the REMO TE MODE button that’ s been programmed with the remote control code for your CD player , CD recorder , or MD recorder , you can control your player with the follo wing buttons. The [CD] bu tton is preprogrammed with the remote con- trol code for controlling an Onkyo CD player .
148 Controlling Other Components —Contin ued By pressing the REMO TE MODE button that’ s been programmed with the remote contr ol code for your Dock, you can control your iPod in the Dock with the follow ing buttons. For some RI docks, the [ON], [ST ANDBY] button may not work with a re mote control code 82990 (without u ).
149 Contr olling Other Components —Continued r PLA Y MODE b utton Selects play modes on components with selectable play modes. W orks as a Resume button when used with a DS-A2 RI Dock. s RANDOM button Used with the shuffle function. Note: W ith some components, certain b uttons may not work as expected, and some may not w ork at all.
150 Controlling Other Components —Contin ued V ia onscreen menu, you can spec ify what actions will be taken by the Easy macro command in the Easy macro mode. Activities Setup 1 Press the [RECEIVER] b utton fol- lowed b y the [SETUP] button. The main menu a ppears o nscreen.
151 Contr olling Other Components —Continued Here ar e the default settings. Source Play Enable: Start playback the source of “Enable”. Disabl e: Start playback the source of “Disable”. This option enables the Source to start playback when the A CTIVI- TIES button is pressed.
152 Controlling Other Components —Contin ued The A V recei ver’ s remote controller can le arn the com- mands of other remote controllers. By tra nsmitting, for example, the Play command from your.
153 Contr olling Other Components —Continued Y ou can pro gram the remote controller’ s A C TIVITIES buttons to perform a sequence of remote control actions. Example: T o play a CD you typically need to perform the follow- ing actions: 1. Press the [RECEIVE R] button to se lect the Recei ver remote controller mode.
154 T roub leshooting If you hav e any trouble using the A V recei ver, look for a solution in this section. If you can’ t resolve the issue yourself, contact your Onkyo dealer . Can’t turn on the A V rec eiver • Make sure that the power cor d is properly plugged into the wall outle t.
155 T r oubleshooting —Contin ued The surround speakers pr oduce no sound • When the DTS Surround Sensation, T -D (Theater- Dimensional), Stereo or Mono listening mode is selected, the surround speakers pro duce no sound. • Depending on the source and current listening mode, not much sound may be produ ced by the su rround speakers.
156 T r oubleshooting —Continued • With some CD and LD players, you won’t be ab le to playback DTS material pr operly ev en though your player is connected to a digital input on the A V receiv er. This is usually because the DTS bitstream has been processed (e.
157 T r oubleshooting —Contin ued The remote contr oller doesn’t wo rk • Make sure that the batteries are installe d with the cor- rect polarity (page 14). • Install new batteries. Don’ t mix dif ferent types of bat- teries, or old and ne w batteries (page 14).
158 T r oubleshooting —Continued Can’t record • On your recorder, make sure the correct input is selected. • T o p revent signal loops and damage to the A V receiv er, input signals are not fed through to outputs with the same name (e.g., T APE IN to T APE OUT or VCR/D VR IN to VCR/D VR OUT).
159 T r oubleshooting —Contin ued The f ollowing se ttings can be made f or the S- Video, composite video an d COMPONENT VIDEO inputs Y ou must use the b uttons on the A V receiver to mak e these settings. 1. While holding do wn the input selector b utton for the input source that you want to set, press the [SETUP] bu tton.
160 Specifications (TX-NR3007) Amplifier Section Video Section Tu n e r S e c t i o n General ■ Video Inputs ■ Video Outputs ■ Audio Inputs ■ Audio Outputs ■ Contr ol T erminal Specifications and features ar e subject to change without notice.
161 Specifications (TX-NR5007) Amplifier Sect ion Video Section T uner Sectio n General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Control T ermi nal Specifications and features ar e subject to change without notice.
162 Video Resolution Char t The following tables sho w how vide o signals at different resolutions are output by the A V receiver. *1: The output i s limited to 480p for an effectiv e signal i n the effect of Macr ovision. *2: The output i s limited to 576p for an effectiv e signal i n the effect of Macr ovision.
163 Memo.
164 SN 29400059 Y0907-1 (C) Copyright 2009 ONKY O CORPORA TION Japan. All rights reserved. http://www.onkyo.com/ HOMEPAGE Sales & Product Planning Div . : 2-1, Nisshin-cho , Ney agawa-shi, OSAKA 572-8540, J AP AN T el: 072-831-8023 F ax: 072-831-8163 ONKY O U .
デバイスOnkyo TX-NR3007の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Onkyo TX-NR3007をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo TX-NR3007の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo TX-NR3007の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo TX-NR3007で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo TX-NR3007を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo TX-NR3007の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo TX-NR3007に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo TX-NR3007デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
