OnkyoメーカーTX-SR574の使用説明書/サービス説明書
ページ先へ移動 of 64
E n AV Receiv er TX-SR574 Instruction Manual Thank you for purchasing an Onkyo A V Recei ver . Please read this manual thoroughly before making connections and plugging in the unit. F ollo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiver .
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The AC fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Precautions —Continued F or British models Replacement and mounting of an AC plug on the po wer supply cord of this unit should be performed only by qualified service personnel.
5 Features Amplifier • 7-channel amplifier • 80 watts per channel rms into 8 ohms, 2 channels driv en, 20 Hz to 20 kHz, less than 0.08% total har- monic distortion (FTC rating) • WRA T (W ide .
6 Enjo ying Home Theater Y ou can use two sets of speakers with the A V receiv er: speak er set A and speak er set B . Speaker set A should be used in your main listening room for up to 7.1-channel playback. *While speaker set B is on, speaker set A is reduced to 5.
7 Contents Introduction Important Safety Instructions ....................2 Precautions ................................................. 3 Supplied Accessories ................................. 4 Features .............................................
8 Getting to Kno w the A V Receiver For detailed information, see the pages in parentheses. A ST ANDBY/ON b utton (32) Sets the A V receiver to On or Standby . B ST ANDBY indicator (32) Lights up when the A V receiver is on Standby and flashes while a signal is being receiv ed from the remote controller .
9 Getting to Know the A V Receiver —Continued J T ONE, [–], and [+] buttons (41) Used to adjust the bass and treble. K STEREO button (43) Selects the Stereo listening mode. L LISTENING MODE [ ]/[ ] b uttons (43) Select the listening modes. M DISPLA Y button (38) Displays various information about the currently selected input source.
10 Getting to Know the A V Receiver —Continued A DIGIT AL IN OPTICAL 1, 2, 3, and COAXIAL These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and D VD players.
11 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or dif ferent types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
12 Remote Controller —Continued Including the A V receiver, the remote controller can be used to control up to sev en different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the six REMO TE MODE buttons.
13 Remote Controller —Continued For detailed information, see the pages in parentheses. A ON/ST ANDBY b utton (32) Sets the A V receiver to On or Standby . B INPUT SELECT OR buttons (37) Used to select the input sources. C MUL TI CH b utton (38) Selects the multichannel D VD input.
14 Remote Controller —Continued By default, the remote controller is set to control an Onkyo D VD player . A ON/ST ANDBY b utton Sets the D VD player to On or Standby . B Number buttons Used to enter title, chapter , and track numbers and times for locating specific points.
15 Remote Controller —Continued By default, the remote controller is set to control an Onkyo CD player . A ON/ST ANDBY b utton Sets the component to On or Standby . B Number buttons Used to enter track numbers and times for locating specific points on CD/MD players.
16 Connecting Y our Speakers F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers that you ha ve.
17 Connecting Y our Speakers —Continued Using a suitable cable, connect the A V receiver’ s SUB- WOOFER PRE OUT to the input on your po wered sub- woofer . If your subwoofer is unpowered and you’ re using an external amplifier , connect the SUBWOOFER PRE OUT to it’ s input.
18 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up an y radio signals without any antenna connected, so you must connect the antenna to use the tuner .
19 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
20 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
21 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver.
22 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV and listen via speaker set B. •T o enjoy Dolby Digital and DTS, use connection or .
23 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a D VD and listen via speaker set B. •T o enjoy Dolby Digital and DTS, use connection or .
24 Connecting Y our Components —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as D VD-Audio or SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel D VD input.
25 Connecting Y our Components —Continued W ith this hookup, you can use your VCR’ s tuner to listen to your fav orite TV programs via the A V receiv er, useful if your TV has no audio outputs. •W ith connection , you can listen to the VCR or D VD recorder e ven via speaker set B.
26 Connecting Y our Components —Continued Connecting a VCR or DVD Recor der for Recording Connection A V receiver Signal flow VCR or D VD recorder Picture quality VIDEO 1 OUT S ⇒ S-Video input Be.
27 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fa vorite TV programs via the A V receiver, useful if your TV has no audio outputs. •W ith connection , you can listen to and record audio from the video source and listen via speaker set B.
28 Connecting Y our Components —Continued ■ CD Play er or T urntable (MM) with Built-in Phono Preamp •W ith connection , you can listen to and record audio from your CD player or turntable and listen via speaker set B. •T o connect the CD player digitally , use connection or .
29 Connecting Y our Components —Continued As of this printing, the Onkyo Remote Interacti ve Dock is the only HDD-compatible component a vailable. ■ For HDD-compatible components that support vide.
30 Connecting Y our Components —Continued •W ith connection , you can listen via speaker set B. •T o connect the recorder digitally , use connections and , or and . The A V receiver has an A C outlet on its rear panel for connecting the power cord of another A V component.
31 Connecting Y our Components —Continued W ith (Remote Interactiv e), you can use the following special functions: ■ A uto P ower On/Standby When you start playback on a component connected via , if the A V receiver is on Standby , it will automatically turn on and select that component as the input source.
32 T urning On the A V Receiver MASTER VOLUME VIDEO STANDBY TONE DISPLAY STEREO DIMMER MEMORY DIGITAL INPUT TUNING MODE AB SPEAKERS TUNER TAPE VIDEO 3 VIDEO 2 VIDEO 1 VCR DVD MULTI CH C D SETUP RETURN.
33 Fir st Time Setup To enjoy Dolby Digital and DTS, you must connect your D VD player to the A V receiver digitally (coaxial or opti- cal). Here are the default assignments.
34 First Time Setup —Continued If the impedance of any of the connected speakers is 4 ohms or more but less than 6, set the minimum speak er impedance to “4 ohms. ” Note: Before you change this setting, turn down the v olume. Note: • This procedure can also be performed on the A V receiv er by using the [SETUP], [ENTER], and arrow buttons.
35 First Time Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using the [SETUP], [ENTER], and arrow buttons. This section explains ho w to specify your speaker con- figuration. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band) .
36 First Time Setup —Continued 6 Use the Down [ ] button to select “Surround, ” and then use the Left and Right [ ]/[ ] but- tons to select Small , Large , or None . Small: Select if the surround speak- ers are small. Large: Select if the surround speak- ers are large.
37 Pla ying Y our A V Components Basic A V Receiver Operation MASTER VOLUME VIDEO STANDBY TONE DISPLAY STEREO DIMMER MEMORY DIGITAL INPUT TUNING MODE AB SPEAKERS TUNER TAPE VIDEO 3 VIDEO 2 VIDEO 1 VCR.
38 Playing Y our A V Components —Continued The multichannel D VD input is for connecting a compo- nent with a 7.1-channel analog audio output, such as a D VD-Audio or SA CD-capable D VD player , or an MPEG decoder . See page 24 for hookup information.
39 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations. ■ AM Frequency Step Setup (not North America and Europe) Y ou must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.
40 Listening to the Radio —Continued ■ T uning into Stations b y Frequency Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Y ou can store a combination of up to 40 of your fav orite AM and FM radio stations as presets.
41 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the bass and treble for the front speakers, except when the Direct or Pure Audio (not North Amer- ican models) listening mode is selected.
42 Common Functions —Continued W ith the sleep timer , you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] b utton.
43 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 45. Selecting on the A V Receiver ■ [PURE A UDIO] b utton (not Nor th American model) This button selects the Pure Audio listening mode.
44 Using the Listening Modes —Continued The following table sho ws which listening modes can be used with each input signal format. : Only a v ailable on 6.1/7.1-channel playback systems. Not av ailable while speaker set B is on. : Only a v ailable on 7.
45 Using the Listening Modes —Continued The A V receiv er’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
46 Using the Listening Modes —Continued DTS-ES Matrix This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1-channel playback. Use it with D VDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.
47 Using the Listening Modes —Continued W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low v olume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone.
48 Using the Listening Modes —Continued The Audio Adjust settings are explained belo w . Input Channel Settings ■ Multiplex This setting determines which channel is output from a stereo multiplex source. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.
49 Recor ding This section explains ho w to record the selected input source to a component with recording capability , and how to record audio and video from dif ferent sources. Y ou can only record to a component that’ s connected to the T APE OUT or VIDEO 1 OUT jacks.
50 Ad v anced Setup Crosso ver Frequency This setting only applies to the speakers that you speci- fied as Small in the “Speaker Configuration” on page 35. To get the best bass performance from your speaker sys- tem, you need to set the crossov er frequency according to the size and frequency response of your speakers.
51 Adv anced Setup —Continued Speaker Distance W ith these settings, you can specify the distance from each speaker to the listening position. Notes: • The Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Front distance.
52 Adv anced Setup —Continued Note: •A quick way to adjust the speak er lev els is to press the remote controller’ s [TEST TONE] b utton to turn on the test tone, use the [LEVEL–] and [LEVEL+] but- tons to adjust the lev els, and use the [CH SEL] button to select the speakers.
53 Adv anced Setup —Continued When using progressiv e scanning on your D VD player , you may find that the picture and sound are out of sync. W ith this setting, you can correct this by delaying the audio signals. Y ou can set it from 0 to 100 milliseconds (ms) in 20 millisecond steps.
54 Contr olling Other Components Y ou can use the A V receiv er’ s remote controller (RC-647M) to control your other A V components, including those made by other manufacturers. This sec- tion explains ho w to enter the necessary remote control code for the component that you want to control (e.
55 Controlling Other Components —Continued Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example.
56 Controlling Other Components —Continued To control another component, point the remote controller at it and use the b uttons explained below . (Y ou must select the appropriate r emote control mode first.) With some A V components, certain buttons may not work as expected, and some may not work at all.
57 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from the w all outlet, wait 5 seconds or more, then plug it in again.
58 Tr oubleshooting —Continued • The surround back speakers are not used with all lis- tening modes. Select another listening mode (page 45). • Not much sound may be produced by the surround back speakers with some sources. • Make sure the speakers are configured correctly (page 35).
59 Tr oubleshooting —Continued The remote controller doesn’t w ork • Make sure that the batteries are installed with the cor - rect polarity (page 11).
60 Tr oubleshooting —Continued The following settings can be made for the S-Video and composite video inputs Y ou must use the buttons on the unit to make these set- tings. 1. While holding down the input selector b utton for the input source that you want to set, press the [SETUP] button.
61 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs Specifications and features are subject to change without notice.
TX-SR574_En.book Page 62 Wednesday, April 5, 2006 5:14 PM.
TX-SR574_En.book Page 63 Wednesday, April 5, 2006 5:14 PM.
64 SN 29344194 I0604-1 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.
デバイスOnkyo TX-SR574の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Onkyo TX-SR574をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo TX-SR574の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo TX-SR574の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo TX-SR574で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo TX-SR574を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo TX-SR574の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo TX-SR574に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo TX-SR574デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
