Optimusメーカー120-1995の使用説明書/サービス説明書
ページ先へ移動 of 18
AM/FM/CD Car Stereo (120-1995) Features Faxback Doc. # 6994 You can install the features-packed Optimus Detachable Face Digital AM/FM/ CD Car Stereo in almost any vehicle. When you remove the detachable control panel, an LED blinks to ward off potential thieves and to show that your stereo is disabled.
AM/FM/CD Car Stereo (120-1995) Installation Faxback Doc. # 6993 For easier installation, the supplied 13-wire harness includes all the lead wires you need to connect the stereo to speakers, power, and optional components. You might need additional wire to complete connections, depending on your individual auto sound system.
terminal. 4. Connect the harness' green wire to the left speaker's negative (-) terminal. Connecting Four Speakers If you are using both front and rear speakers, set 4CH/2CH on the left side of the stereo to 4CH. Then connect the speakers to the supplied harness as follows.
simply turns it on or off. If you do not use this wire, use a wire tie to keep it out of the way. If your vehicle has an automatic antenna, connect the AMP REMOTE TURN ON lead to the vehicle's power Antenna lead. Note: The optional component must be designed for use with an amp remote turn on lead for the above connection.
After you connect the speakers, power wires, and antenna, turn on your vehicle's ignition and test the stereo to be sure it works. If the stereo does not work, immediately unplug the harness. Recheck your connections or have a professional automotive audio installer complete the installation.
2. If you attached the metal strap, release it. 3. Push the sleeve keys into the slots on the right and left of the front panel (with the tab facing up) until you hear a click.
AM/FM/CD Car Stereo (120-1995) Operation Faxback Doc. # 6992 RESETTING THE SYSTEM If the stereo does not work when you first install it, or if it stops working, press RESET. This clears any programming except the station presets and the stereo should begin to work.
5. FADER-Press SEL until F and O appear on the display. Press + or - to adjust the balance between the front and rear speakers (if you use both). FF and a number appear on the display when the fader is shifted to the front. FR and a number appear when the fader is shifted to the rear.
not work. Caution: Do not touch the contact on the control panel or on the stereo's body, since this may result in poor electrical contact. If dirt or other foreign substances get on the contacts, wipe them off with a dry cloth. PLAYING THE RADIO 1.
select A1 to store the first group of AM stations. 3. Tune to the station which appears on the band immediately before the first station you want to store in memory. 4. Press and hold down AMS for 3 seconds. The system scans the selected band and then stores the next six strong stations.
PLAYING A CD Cautions: * The CD player has a wide dynamic range. As a result, if you turn your CD player's volume too high during soft (low volume) sections of a program, you might damage your speakers when a sudden loud passage occurs.
then advances to the next track, plays it for 10 seconds, and so on. To cancel into scan, press INTRO. INT disappears from the display and the CD player resumes normal play of the current track. Repeat Play You can play a selected track repeatedly. Simply press REPEAT while the track you want to repeat is playing.
AM/FM/CD Car Stereo (120-1995) Specifications Faxback Doc. # 6991 CD SECTION (At Line Output Frequency Response (+/-3 db)..................................20-20,000Hz S/N Ratio (A-WTD)...................................................80 dB Separation.
Dimensions........2 1/4 x 7 3/8 x 7 9/16 inches (50 x 178 x 160 mm) (HWD) Weight...................................................5.3 lbs (2.5 kg) Specifications are typical; individual units may vary. Specifications are subject to change without notice.
Audio Connection Information (120-Series) Plug/Male 2 Ch. System Faxback Doc.# 19994 +----+--------------+---------------+------------+------------------------+ |Pin | | | | | |No.
(2CH/4CH SWITCHABLE UNIT) +----+--------------+---------------+------------+------------------------+ |Pin | | | | | |No. | WIRE COLOR | WIRE SPECS. | LABEL | REMARK | +----+--------------+-----------.
|Pin | | | | | |No. | WIRE COLOR | WIRE SPECS. | LABEL | REMARK | +----+--------------+---------------+------------+------------------------+ | 1 | WHT/BLK | AWG #20 | FRONT L- | STRIP SOLDER | | | | .
+---------+--------------+ | White | Right (-) | +---------+--------------+ | Brown | Left (+) | +---------+--------------+ | Gray | Left (-) | +---------+--------------+ | Red | +12 V Power | +------.
デバイスOptimus 120-1995の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Optimus 120-1995をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOptimus 120-1995の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Optimus 120-1995の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Optimus 120-1995で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Optimus 120-1995を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOptimus 120-1995の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Optimus 120-1995に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOptimus 120-1995デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。