Oracle Audio TechnologiesメーカーVの使用説明書/サービス説明書
ページ先へ移動 of 12
O RACLE A UDIO D ELPHI MARK V turntable 1 O WNER’S MANUAL by Oracle Audio Technologies inc..
T ABLE OF CONTENTS Forewo rd .................................................................................................... 1 How to ... ... pack and unpack y our Del phi ................................................................. 2 ... assemble the sub cha ssis .
ow to ... ... pack and unpack your Delphi H - Remove the inner box by lifting it straight up and out. Open the flaps on both ends and slide out the styrofoam packaging.
4 - Locate the bearing assembly in the lower se ction of the packaging. Remove the 3 mounting screws. - Locate the tool kit in the lower section and select the appropriate allen key... 9/64th - Lift the subchassis straight up and mount the bearing assembly from underneath (ground lug side).
5 Important ! If you are planning to cut your own mounting board, remember that the cutting of the arm board can sometimes be troublesom e as well as being a potential hazard. The use of an adequate tooling is important to both accuracy and safety. - Use stainless steel or aluminum screws to mount the cartridge for maximum rigidity.
6 changing the position of the spring in its holder. The color coding is visible from the inside at the wider end of the spring. Note 2: The reference to clockwise or counter-clockwise is determined by viewing the spring from above, unless otherwise mentionned.
- Place the subchassis over the suspension modules. - Install the platter without the drive belt. - Locate the suspension gauge in the documentation envelope. - Punch the suspension gauge out of the card. Do not consider "A", nor 1 & 2, they were used on the earlier models.
8 be done by simply lifting the suspension housing just enough so you can see the spring. If you can see the spring anywhere from almost flush to up to 3 coils out of the spring holder, the spring is in a safe range.
9 Note 3: In the event that the drive belt becomes contaminated, clean it with denatured alcohol. Clean the motor pulley and the drive hub at the same time. ... remove the platter with the drive belt installed Note: The following is not an operation related to the assembly of your Delphi but a procedure to prevent overstretching the drive belt.
... attach the ground lead - Loosen the thumb nut from under the sub-chassis near the tonearm and insert one end of the lead. - Attach the other end of the lead to the ground post of your pre-amplifier.
11 Check: - drive belt - motor connection plug for a broken wire - drive module for a broken wire - defective drive module ... if the platter is not parallel with the plinth Check: - suspension calibr.
12 to firmly secure the screws. Do not forget to add the content of one oil vial (about 3 cc) before installing the platter. - As a precaution to preserve the furniture your Delphi sits on, it is advisable to use a folded paper towel under the main bearing for a few weeks in the case of a bearing spillage.
デバイスOracle Audio Technologies Vの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Oracle Audio Technologies Vをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOracle Audio Technologies Vの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Oracle Audio Technologies Vの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Oracle Audio Technologies Vで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Oracle Audio Technologies Vを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOracle Audio Technologies Vの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Oracle Audio Technologies Vに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOracle Audio Technologies Vデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
