Oregon ScientificメーカーBAR623の使用説明書/サービス説明書
ページ先へ移動 of 19
1 EN CONTENTS Contents ................................................................ 1 Introduction ........................................................... 2 Product Overview ................................................. 2 Front View ......
2 EN INTRODUCTION Thank you for selecting the Oregon Scientific™ Wireless W eather Station (BAR623P / BAR623PU). This device bundles precise time keeping with a projection clock, weather forecast, and indoor and outdoor temperature monitoring features into a single tool you can use from the convenience of your home.
3 EN BACK VIEW 1. Projector FOCUS knob 2. Projector IMAGE ROT A TION knob 3. PROJECTION ON / OFF switch 4. AC / DC adaptor plug cover 5. Battery compartment (cover off) 6. SEARCH button to locate the remote sensor 7. MEM : View current, maximum, and minimum temperature readings 8.
4 EN LCD DISPLA Y 1. Weather display 2. Radio Frequency (RF) reception icon 3. Alarm activated 4. Alarm setting 5. T ime 6. Indoor temperature 7. Low battery icon for main unit 8. ° C / ° F (Outdoor temperature) 9. Sensor signal 10. Low battery icon for sensor 11 .
5 EN REMOTE SENSOR (THN122N) 1. Wall mount hole 2. RESET hole 3. CHANNEL number ( 1-3 ) 4. Battery compartment (Battery compartment cover not shown) 1.
6 EN UNIT LOCA TION Main Indoor T emperature Area Remote Outdoor T emperature Area Installing the batteries: GETTING ST ARTED BA TTERIES Batteries are supplied with this product: Main unit 3 x UM-3 (AA) 1.
7 EN AC ADAPTOR The main unit has a 4.5V AC / DC adaptor with jack, which provides continuous clock / temperature projection. Inserting the adaptor: CHANGE SETTINGS To change, time, calendar and language settings: 1. Press and hold MODE for 2 seconds to enter setting mode.
8 EN Installing the batteries: REMOTE SENSOR (THN122N) This product is shipped with a THN122N Thermometer Sensor that collects T emperature data. The main unit can be connected to only 1 remote sensor. SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver.
9 EN For best results: • Insert the batteries and select the channel before you mount the sensor. • Place the sensor out of direct sunlight and moisture.
10 EN To force a manual search for clock signals, press and hold for 2 seconds. If no signal is found, check the batteries. TURN CLOCK ON / OFF Perform this step if you cannot receive clock signals. Press and hold for 2 seconds. Then, manually set the clock following the “Set Clock” instructions (below).
11 EN SET CLOCK / CALENDAR Y ou only need to do this if you have disabled the clock feature (for example, if you are too far from or cannot receive a signal). 1. Press and hold MODE for 2 seconds. The Clock Area will blink. 2. Select the hour, minute, year, month, day, and day of the week language.
12 EN SILENCE ALARM When the alarm time is reached, the crescendo alarm will sound for 2 minutes. T o silence the alarm: • Press SNOOZE to silence it for 8 minutes. OR •P ress any key except SNOOZE to mute the alarm and activate it again after 24 hours.
13 EN MOON PHASE The Calendar must be set for this feature to work, see “Set Clock” section. • Press or to view the moon phase for the next or previous day.
14 EN RESET SYSTEM The RESET button is located in the main unit battery compartment. Press RESET when you change the batteries and whenever performance is not behaving as expected (for example, unable to establish radio frequency link with remote sensor or clock).
15 EN • Never immerse the product in water . This can cause electrical shock and damage the product. • Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. • Do not tamper with the internal components.
16 EN SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H 92 x 167 x 53 mm (3.6 x 6.6 x 2.1 inches) W eight 228 grams (8.04 ounces) without battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm (3.
17 EN Calendar DD / MM; weekday in 5 languages (E, D, F, I, S) Alarm Single alarm with 2-minute crescendo and 8-minute Snooze Projector Outdoor temperature and time POWER Main unit batteries 3 x UM-3 (AA) 1.5V Sensor batteries 2 x UM-4 (AAA) 1.5V AC / DC adaptor 4.
18 EN EC-DECLARA TION OF CONFORMITY This product contains the approved transmitter module that complies with the essential requirements of Article 3 of the R&TTE 1999 / 5 / EC Directive, if used as intended and the following standards have been applied: Safety of information technology equipment (Article 3.
19 EN W ireless W eather Station Model: BAR623P / BAR623PU User Manual BAR623P_EN_R2.p65 7/27/04, 12:40 AM 19.
デバイスOregon Scientific BAR623の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Oregon Scientific BAR623をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOregon Scientific BAR623の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Oregon Scientific BAR623の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Oregon Scientific BAR623で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Oregon Scientific BAR623を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOregon Scientific BAR623の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Oregon Scientific BAR623に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOregon Scientific BAR623デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。