Orion Car AudioメーカーORION MaxxBassの使用説明書/サービス説明書
ページ先へ移動 of 17
Maxx Bass ®.
T ABLE OF CONTENTS Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . . . .
CONGRA TULA TIONS Thank you for choosing Orion audio equipment. At Orion we proudly design, engineer and manufacture audio products for aftermarket car audio. Our award winning engineering team utilizes innovative technology to consistently deliver Absolutely State of the Art performance, sound quality , reliability , and value.
recommended in two configurations. (Please see Wiring Configurations for more details.) 1) Front Stereo Configuration One Maxx Bass ® Processor is used between the front channel source and front speaker amplifier to increase the bass response on only the front speakers.
This is accomplished using the science of psychoacoustics on how we perceive sound. By building audio systems optimized for how we hear sound, significant performance improvements can be obtained. This is analogous to designing and building televisions that only display red, green and blue dots.
5 MAXX BASS ® SIGNAL FLOW FEA TURES Selectable Maxx Bass ® Frequency Setting of 60Hz and 80Hz Green LED clip/Red LED power indicator signal Gold 2 Channel in/2 channel buf fered full-ran.
SPECIFICA TIONS Frequency 20hz-20kHz Signal-to-Noise Ratio >85dB Separation 65dB @ 1kHz Crossover Slope 24dB/octave Input Impedance 20,000 Ohms Input Sensitivity variable, 300mV to 3V peak to peak .
MAXX BASS ® OUTLINE AND DIMENSIONS MI NM A X I N TEN SI TY MI NM A X OU T P U T I NP UT MI NM A X 80H z 60H z ON OF F F RE Q UE NCY CROS S O VER I NP UT OUT P UT P O W E R RE M OT E G ND RE M +12V RE M OUT ( 11. 5 cm ) ( 6. 3 cm ) ( 14 cm ) ( 3 cm ) 1.
WIRING CONFIGURA TIONS The Maxx Bass ® Processor is recommended in two different configurations. 1. Front Ster eo Configuration The figure below illustrates the wiring for a front stereo configuration.
2. Dual Stereo Configurations For systems without rear subwoofers, the user may prefer to use two Maxx Bass ® Processors, one for the front speakers and one for the rear speakers. The units should be wired between the in-dash CD Receiver and the power amplifiers as shown below .
The ground wire should be of the same gauge wire as the power wire. As a rule of thumb, use as short length of wire as possible. Find a location near the Maxx Bass ® Processor that is metal ( the floor is ideal) and clean an area about the size of a quarter to bare metal.
INPUT T o use Speaker Level Inputs (common ground head units only), connect RCA plugs to the front or rear speaker leads as shown. NOTE: It is important to connect an input signal to both RCA input jacks if a stereo amplifier is used, otherwise the connected channel receives full range and the disconnected channel will receive only the harmonics.
MAXX BASS ® PROCESSOR SETTINGS T o achieve proper performance it is important to set or tune the settings on the Maxx Bass ® Processor to the final system. This section recommends initial settings and the users can then further adjust these for optimal listening.
TROUBLESHOOTING NO SOUND Is the POWER LED lit? YES NO Check Input cables for signal by Check power and remote Connecting them straight to the turn-on wire for voltage. Subwoofer amplifier . Make sure the ground wire is Secure. ANY SOUND NOW? YES NO Problem is in the Crossover .
OPPOSITE CHANNEL SAME CHANNEL Reverse RCAs to head unit Problem is in the Crossover . (Check Balance Control) See your local Authorized Orion dealer . SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL Problem is in the head unit. Problem is in the RCA cables.
15.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under .
デバイスOrion Car Audio ORION MaxxBassの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Orion Car Audio ORION MaxxBassをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOrion Car Audio ORION MaxxBassの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Orion Car Audio ORION MaxxBassの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Orion Car Audio ORION MaxxBassで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Orion Car Audio ORION MaxxBassを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOrion Car Audio ORION MaxxBassの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Orion Car Audio ORION MaxxBassに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOrion Car Audio ORION MaxxBassデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。