Packard BellメーカーW7の使用説明書/サービス説明書
ページ先へ移動 of 18
Packard Be ll EasyNote W7 Se ries (Dragon SN) Disassembl y Manual.
0 Table of C ontents Overv iew 1 Disassem bl y Inst ructions 1 Reassem bly Instructions 1 Required Too ls 1 Hazardous V oltage 2 Avoid E l ectrostat ic Discharge 2 Pow er Supply Un it 2 Battery and AC.
1 Overview This docum ent contains step-by-step disass em bly i nstructions for the Easy Note W 7 (Dragon SN) chass i s. The instruct ions are illust rated w here n ecessary w ith im ages of the part that is be ing rem oved or d isassem bl e d. Packard Bell rese rves the right to m ake changes to the chass is without not i ce.
2 Hazardous Vol tage There is hazar dous voltage p resent inside the com puter when it is connect ed to an AC supply, even w hen the com puter’ s pow er sw itch i s off.
3 WAA R SCHUWING Zorg er voor dat a lle verbind in gen v an en naar de com puter (stroom, m ode m, netw erk, etc) verbroken w orden voordat de behu izing geopend wordt.
4 Battery a nd AC Adapter To rem ove the battery, d o as follow s: 1. Turn off the com puter. 2. Disconn ect the AC ad apter. 3. Rem ove the batte ry. Removing the Hard Disk Drive To rem ove the hard disk d rive, perform the follow in g steps: 1. Remove two screws (2 xA) from the HDD cove r (as sh ow n in Fig.
5 Bottom Panel Perform the follow ing steps to remove the bott om panel: 1. Rem ove nine screw s (9xA) and take aw ay the bottom panel. 2. Rem ove the m e m ory m odule. 3. Lift out th e TV Tuner M i n i-PCI card from its slot. 4. Disconn ect the antenna cable and the tw o data cables.
6 7. Remove the screw s (2xA) from the m ode m . 8. Release the ground cable and tak e aw ay the m ode m . 9. Disconnect the m odem cable from the m ode m. CP U, V GA Module an d Heat S ink To rem ove the heat s in k from the CPU and th e VGA M obi le PC I Express M odul e (MX M) follow the steps below : 1.
7 6. Re m ove the screw from the VGA m odul e (1xT). 7. Pull the VGA m odul e out of the MXM slot. 8. Unlock the CPU socket an d rem ove the CPU. Top Cover Rem ove the top cover by f ollow in g the steps b elow: 1. Slide the button bar to the left to unlock it.
8 6. Disconnect the touchpad f l at cab l e. 7. Re m ove the two hi ng e covers. 8. Disconnect the lid switch conn ector. 9. Rem ove the screw (1xD) and rem ove the lid sw itch unit. Fig. 1 0 Removi ng the keyboa rd flat cabl e . Fig. 1 1 Di sconnect i ng t ouchp ad flat cable Fig.
9 Removing the LC D Panel Asse mbly Follow the steps below to remove the LCD pa nel : 1. Disconnect the two LCD connectors. 2. Release the W ireless antenna ca ble. 3. Rem ove the screws (4xF) from the hinges (see Fig. 13). 4. Take away the LCD assem bl y.
10 Fig. 1 5 LCD di sp lay panel . 10. Disconnect the inverter backlight connector. Fig. 1 6 LCD i nverter backli ght connecter. 11. Rem ove the lower support ing bracket. 12. Take aw ay the LCD display panel and inverter board. 13. Disconn ect the LCD cab le from the inverter b oard.
11 15. Rem ove the screws (3x D, 1xA) from the l eft L CD bracket. The sam e goes for the right bracke t. Fig. 1 8 LCD di sp lay cabl e. 16. Take away the top, left and right bracket from the LCD display pane l. 17. Rem ove the screws (2xD) holding the w ireles s antenna and take away the antenna.
12 Optical Di sk Drive To rem ove the optica l disk dr ive, fo llow the steps be lo w : 1. Remove the screws (2xB) and push t he opt i cal d isk d rive out of i ts bay. Fig. 2 0 The sc re ws o f the op ti cal di sk dr i ve. 2. Rem ove the screw s (2xK) from the side ODD bracket and remove it.
13 Bottom Base Asse mbly Disassem bl e the bottom base assembly as fo llows: 1. First remove the screw s (4XA) from the top cover. 2. Then rem ove the screws (4xJ). No te: Mak e su re tha t du ring re -as se mbl y the c lips o f the top co ve r loc k i nto plac e be fore fas tenin g the scre ws.
14 4. Re m ove the screws from the rear (2x B). 5. Remove bottom cover from base assem bl y. 6. Disconnect the s ubwoofer conn ector. 7. Rem ove the screws (2x G) and lift out the s ubw oofer assem bl y. 8. Re m ove the rubber stab ili z ers (2x M) fro m the subwoofer assem bl y.
15 8. Take away the m ain board. 9. Partially rem ove the foil over the to uchpad. 10. Disconnect the touchpad cable. 11. Remove the screws (3xB) and rem ove the heat plate. 12. Push out the touchpa d assem bly. Fig. 2 6 The mai n board and speake rs .
16 Notice The inform ation in this guide is subj ect to cha nge without notice. This guide c ontains inform atio n protect ed by copyr ig ht. No part of th is guide m ay be photocop ied or reproduc ed in any f orm or by any m eans without pr ior w ritten cons ent from NEC Computers Intern ational BV.
デバイスPackard Bell W7の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Packard Bell W7をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPackard Bell W7の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Packard Bell W7の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Packard Bell W7で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Packard Bell W7を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPackard Bell W7の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Packard Bell W7に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPackard Bell W7デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。