Palsonicメーカー4890の使用説明書/サービス説明書
ページ先へ移動 of 19
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 48CM CORDLE.
Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference.
. This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured.
CONTROL PANEL REMOTE SENSOR POWER INDICATOR ANTENNA INPUT AV IN OUT 1. ANTENNA CONNECTIONS 1.1 Optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture. 1.2 Insert the out-door antenna into the antenna socket on the cabinet back.
3.1 STANDBY ( ) Button 3.1.1 Press STANDBY ( ) button to turn on the set (the indicator shows yellow) when the set is in STANDBY mode (the indicator shows red) , the channel position number is displayed in the screen. Press STANDBY ( ) button to return the set to the STANDBY mode when the set is in OPERATION mode, and the indicator shows red.
3.2.2.4 Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position, 3.2.2.5 Repeat 1~ 4 steps to search another channel. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased.
3.5 VOLUME CONTROL 3.5.1. Press the VOL button to increase volume ; the green bar on the screen moves right. 3.5.2. Press the VOL button to decrease volume ; the green bar on the screen moves left. 8 Display of minimum volume Display of maximum volume .
4. REMOTE CONTROL OPERATION: REMOTE CONTROL UNIT : STANDBY 1 ~ 9 : DIGITAL CHANNEL SELECTOR 10/0 : CHANNEL 10 OR CHANNEL 0 SELECTOR SYSTEM : COLOUR SYSTEM CONTROL -/- - : DIGIT OR TWO DIGIT CHANNEL SELECT : PREVIOUS 4.1 INSTALLING BATTERIES: 4.1.1 Remove the battery cover of Remote Control Unit.
4.3 CHANNEL SELECTION 4.3.1 Press CHANNEL SELECTOR ( ) the channel number will be increased or decreased and displayed in the upper right corner of the screen.
6 5 4.3.3 PREVIOUS BUTTON Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach channel 15, press it again to return channel 6.
4.6 Making use of PPS button (personal preference select) Press the PPS button, the screen will display the following five mode progressively: Press PPS again Press PPS again The above five display modes corresponding analogue quantity is shown in the following chart: BRIGHTNESS 4.
4.8 SLEEP BUTTON 4. 8. 1 Using SLEEP button allows you to have the appliance automatically turned off after a pre-determined time, and set the appliance to STAND BY mode. 4. 8. 2 After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes.
4.9.1 CLOCK 4.9.1.1 Press the TIMER button till "CLOCK" displays-on the screen. 4.9.1.2 Press the button to set the present hour. Press the button to set the present minute. 4.9.1.3 After setting the clock, press TIME SET button to start operating.
AUTO 4.9.8.8 Press TIME SET button, then the OFF TIME indication is green instead of red. OFF TIME function starts operating. 4.9.8.4 The appliance will be turned off when your setting time is up, and return to stand by mode. NOTE: * The built-in clock employs the 24-hour system.
5. 2. 2 Press AV/TV button of the TV set or on the remote control unit to set the set to TV mode, and choose the desired channel. Note: the following mis-operation should be avoided during recording. * Press STANDBY button or set to VIDEO mode. * Change the current channel accidentally.
5. 3. 2 Press AV/TV button of the TV set or on the remote control unit to select Video mode before dubbing, "VIDEO" will be displayed on the screen. The TV set will act as a monitor to help you edit while dubbing. NOTE: The set MUST remain in Video mode and MUST NOT be switched off during the session.
6. TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other equally similar simple causes. If any problem arises in the operation of your set, first check through this list of symptoms and correction.
7. SPECIFICATIONS: TV System: Receiver Channel Cable Channel Power supply CRT Antenna Impedance Dimension (mm) Weight Power Consumption Remote Control Unit Power Supply * Design and specifications are subject to change without notice. : PAL, B/G; NTSC 3.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-51703-.
デバイスPalsonic 4890の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Palsonic 4890をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPalsonic 4890の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Palsonic 4890の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Palsonic 4890で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Palsonic 4890を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPalsonic 4890の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Palsonic 4890に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPalsonic 4890デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。