PanasonicメーカーAK-HC910Pの使用説明書/サービス説明書
ページ先へ移動 of 36
AK-HC910P Before attempting to connect, operate or adjust this product, please read these instructions completely. 1080I Multi-purpose Digital Camera.
2 FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached instal- lation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
3 For Your Safety...................................2 Preface ...............................................4 Features..............................................4 Precautions .........................................5 Major Operating Controls and Their Functions .
4 Preface Thank you very much for purchasing the multi-purpose digital camera. New 2/3 q 2.2 million-pixel CCD is employed. [1920(H) k 1080(V)] • 2.2 million-pixel CCD is 2/3 q size, being compact and light-weight. The camera section is equipped with a high picture quality digital signal processing LSI.
5 • Do not attempt to disassemble the camera or other units. In order to prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. • Do not abuse the camera. Avoid striking, shaking, etc. The camera contains sensitive components which could be damaged by improper handling or storage.
6 Major Operating Controls and Their Functions _ Front Panel 5 Cooling Fan • Do not block or obstruct the ventilation during operation. It may otherwise cause internal heating or fire. • The life of this fan is approximately 50,000 hours (at room temp.
7 8 Breaker [BREAKER] If the breaker is operated due to over-current or the like, check the cause and eliminate the trouble, then press the breaker button.
8 BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F 720 PROGRESSIVE How to Install _ How to set the lens • Standard 2/3 q bayonet type (B4 mount) lens of any makers can be used*. 1 Turn the lens fixing ring knob counterclockwise to remove the lens mount cap.
9 O I BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F AK-HC910P YPbPr D-sub 15-pin D-sub 15-pin How to Set Up the System (Connection) _ Connection of remote control box • Use multi-cable for the connection of HD controller AK-HRP900 and this unit.
10 O I BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F HD-SDI D-sub 15-pin D-sub 15-pin Multi-cable (5m) AK-HDMLTCA05 Coaxial Cable (5C-FB) AC Adaptor AW-PS505 HD Controller AK-HRP900 HD Monitor Multi-purpos.
11 O I BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F G/L IN P b OUT P r / SDI OUT Y/ VIDEO OUT 1394 CONTROL IN IP/RP DC12V IN CAMERA I/F LENSE I/F ND/EXT SDI IN CS O P O I HD-SDI Pan/Tilt Head Contro.
12 O I BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F O I HD-SDI Multi-cable (5m) AK-HDMLTCA05 Coaxial Cable (5C-FB) AC Adaptor AW-PS505 DC Power Cable HD Controller AK-HRP900 HD Monitor Remote controllable.
13 O I BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F G/L IN P b OUT P r / SDI OUT Y/ VIDEO OUT 1394 CONTROL IN IP/RP DC12V IN CAMERA I/F LENSE I/F ND/EXT SDI IN CS O P O I O I HD-SDI Multi-cable (5m).
14 Operation Procedure 1 Turn on the power of each equipment. 2 Properly adjust the light for the object. 3 Adjust the flange back of the lens, the iris and the focus. • Flange back must be adjusted when the camera is used for the first time or after replacement of the lens.
15 _ Flange back adjustment (for zoom lens) The adjustment is to adjust the focus in all the range from the maximum zoom to the widest angle of the zoom lens. 1 Shoot a dark object to open the iris. 2 Adjust the distance from the object to 6.6 ft. (2 m) at least, then loosen the flange back fixing knob of the lens.
16 _ Color temperature and while balance adjustment (reference) When carbon is burnt, it develops various colors of light depending on the temperature. Natural light can be specified by color temperature reflecting to the color developed when carbon is burnt.
17 H.PHASE H.PHASE-COARSE :03 H.PHASE-FINE :40 °° °° _ Black balance adjustment • Adjust it with the lens closed. When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed.
18 USER MENU 1.MAINTENANCE 2.SETTING 3.CAM ID 4.FILE MENU MAINTENANCE 1.BLACK SHADING 2.PED,GAMMA,FLARE 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.S.GAIN 3 10.
19 USER MENU 1.MAINTENANCE 2.SETTING 3.CAM ID 4.FILE MENU Setting of Menu Items _ USER menu (Initial screen) The readout data at start of power supply is the data just before cutting off the power supply, and the operation is started with the data.
20 MAINTENANCE 1.BLACK SHADING 2.PED,GAMMA,FLARE 3.KNEE,WHITE CLIP 4.R/B GAIN 5.DTL 6.GAIN,AUTO IRIS 7.S.GAIN 1 8.S.GAIN 2 9.
21 PED,GAMMA,FLARE M PED :+027 R PED :+000 B PED :+000 M GAMMA :0.45 R GAMMA :+00 B GAMMA :+00 R FLARE :010 G FLARE :000 B FLARE :017 GAMMA :ON FLARE :ON .
22 KNEE,WHITE CLIP M KNEE POINT :95.00% R KNEE POINT :+00.00% B KNEE POINT :+00.00% M KNEE SLOPE :95.00% R KNEE SLOPE :+000 B KNEE SLOPE :+000 A.
23 R/B GAIN R GAIN :+000 B GAIN :+000 °° °° DTL DTL :ON TOTAL DTL LVL :+00 H DTL LVL :11 CRISP :02 LVL DEPENDENT :2 PEEK FREQUENCY :10 KNEE APERTURE :ON KNEE APA.
24 DTL DTL :ON TOTAL DTL LVL :+00 H DTL LVL :11 CRISP :02 LVL DEPENDENT :2 PEEK FREQUENCY :10 KNEE APERTURE :ON KNEE APA.LVL :10 SLIM DTL :OFF DTL(+) :+00 DTL(-) :+00 DTL CLIP :0 DTL SOURCE :(B+G)/2 °° °° GAIN,AUTO IRIS LOW GAIN :0dB MID GAIN :9dB HIGH GAIN :18dB A.
25 S GAIN 1 TOTAL GAIN :42dB ANLG GAIN :36dB PIX MIX :06dB H DTL LVL :00 CRISP :0 LEVEL DEPENDENT :5 PEAK FREQUENCY :2 M GAMMA :0.
26 Setting of Menu Items ! Maintenance menu 8 Matrix menu Selection of table A, B or OFF. Adjustment of gain of each color. < MATRIX > MATRIX TABLE :A MATRIX R-G :+00 MATRIX R-B :+.
27 SETTING 1.MODE 2.SHUTTER 3.H.PHASE °° °° MODE BLACK STRETCH :OFF D5600K :OFF CABLE COMPE :0m SUP GAIN :OFF CAM ID :BAR CAM ID POSI :0 MATRIX TABLE :OFF COLOR CORRECTION :OFF STATUS :ON °° °° Setting of Menu Items @ Setting menu - Menu for various settings.
28 Setting of Menu Items SHUTTER SHUTTER MODE :OFF SHUTTER SPEED :1/100 SYNCHRO SCAN :75.1 °° °° H.PHASE H.PHASE-COARSE :09 H.PHASE-FINE :40 °° °° @ Setting menu 3 Horizontal phase adjustment menu for external reference signal H.
29 °° CAM ID ID:AKHC900 °° H FILE MENU FILE :USER1 SAVE FILE? :USER1 SAVE : °° H FILE MENU FILE :USER1 SAVE FILE? :USER1 SAVE : °° Setting of Menu Items # Camera ID setting menu $ File managing and renewing menu - File operation menu : blinking display.
30 H FILE MENU FILE :USER1 SAVE FILE? :USER1 SAVE : ° FILE MENU FILE :USER1 SAVE FILE? :USER1 SAVE IN USER1.OK? YES NO °° FILE MENU FILE :USER1 SAVE FILE? :USER1 SAVE IN USER1.
31 BREAKER ZOOM/ FOCUS SDI OUT 1 2 1 / F LENS 1/2 q (12) 4-3/8 q (1 10) 4-15/16 q (125) 7/16 q (10) 5/8 q (15) 6-5/16 q (160) 13/16 q (20) Outside Dimension Diagram ( ): mm.
32 1 indicates safety information. Image pickup device: 2/3 q 2.2 million-pixel FIT CCD k 3 System: GBR image pickup system Resolving optical system: F1.4 prism Optical filter: CC: clear, 4300K, 6300K, cross ND: 100%, 25%, 6.3%, 3.2% Lens mount: Bayonet type Output spec.
.
.
.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE.
デバイスPanasonic AK-HC910Pの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic AK-HC910Pをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic AK-HC910Pの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic AK-HC910Pの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic AK-HC910Pで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic AK-HC910Pを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic AK-HC910Pの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic AK-HC910Pに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic AK-HC910Pデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
