PanasonicメーカーAW- PH350の使用説明書/サービス説明書
ページ先へ移動 of 34
Before attempting to connect, operate or adjust this product, please read these instructions completely. Indoor pan-tilt head Model A W - P F1101W @ Printed in Japan VQT9583 P.
2 indicates safety information. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
3 indicates safety information. Replace battery with part No. CR2032 only. Use of another battery may present a risk of fire or explosion. Caution—Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. FCC Note: This device complies with Part 15 of the FCC Rules.
4 O This is a compact stand-alone type of pan-tilt head which is capable of rotating 95 degrees upward and downward and 300 degrees on the horizontal. O This pan-tilt head can bear a total weight of up to 8.8 lb (4 kg) for the camera and lens combined.
5 Installation precautions O Avoid using the pan-tilt head in kitchens or other places where there is excessive steam and oil fumes. O Make sure that the installation of the pan-tilt head has been completed before mounting the camera onto it. O This pan-tilt head has a maximum load capacity of 8.
6 Precautions f or use This pan-tilt head uses a manganese dioxide-lithium battery (CR2032). Be absolutely sure to remove this battery when disposing of the pan-tilt head or printed circuit boards. Be sure to dispose of any batteries removed according to the applicable regulations of the country concerned.
7 Pa r ts and their functions G/L I N Pb OUT Pr /SDI OUT Y/VI DEO OUT 1394 CONTROL IN IP/RP DC12V IN CAMERA I/F LENSE I/F ND/EXT SDI IN CS O P +- LAMP CONTROL 2 1 6 4 3 ? 8 9 ; @ < : = 9 5 7 >.
8 Pa r ts and their functions = Safety wire mounting hole This is used when attaching a wire to prevent the pan-tilt head from dropping. > Base connector panel This is used for connection with a controller, multi-port hub or AC adapter for the pan-tilt head.
9 Installation (The installation work must be performed by your dealer without fail.) $ Assembling the pan-tilt head Be absolutely sure to hold the pan-tilt head by the base when handling it. O Attaching the tilting arm Use the tilting arm fixing screws to attach the tilting arm.
10 SW3 SW4 OFF ON SW2 1234 Installation (The installation work must be performed by your dealer without fail.) $ Setting the installation direction selector switc h and landing c haracteristics Set the switches as follows to perform a stand-alone installation and/or to select the landing characteristics.
11 OFF ON Installation (The installation work must be performed by your dealer without fail.) $ Setting the cable compensation cir cuit A maximum length of up to 3,280 feet (1,000 meters) is allowed for the cable between each pan-tilt head and the multi-function controller (AW-RP605) (when BELDEN 8281 coaxial cables are used).
12 Installation (The installation work must be performed by your dealer without fail.) $ Moving the mounting position of the base connector panel If necessary, the mounting position of the base connector panel can be moved. (When the pan-tilt head is shipped, it is positioned for suspended installation.
13 t t Installation (The installation work must be performed by your dealer without fail.) $ Installing the pan-tilt head Be absolutely sure to follow the instructions below when installing the pan-tilt head. Failure to do so may cause the pan-tilt head to slip out of position or fall.
14 Installation (The installation work must be performed by your dealer without fail.) $ Mounting the camera The pan-tilt head’s camera mounting section has a mechanism for maintaining the camera’s balance that moves the camera mounting plate using a guide roller as a fulcrum.
15 Adjust the balance by moving the camera mounting plate. <Mounting example 2> Installation (The installation work must be performed by your dealer without fail.
16 Installation (The installation work must be performed by your dealer without fail.) O Attaching the chain 1. Attach one end of the chain to the pan-tilt head using a chain attachment screw (M4 a 8 mm: with flat washer/spring washer).
17 Installation (The installation work must be performed by your dealer without fail.) O Mounting a camera When mounting a camera to the pan-tilt head, take appropriate measures to prevent the camera from falling or being stolen. 1. Place the camera on the camera mounting base and insert the guide pin into the guide hole on the camera.
18 G/L I N Pb OUT Pr /SDI OUT Y/VI DEO OUT 1394 CONTROL IN IP/RP DC12V IN CAMERA I/F LENSE I/F ND/EXT SDI IN CS O P O I CAMERA I/F LENSE I/F ND/EXT SDI IN 1 3 G/L I N Pb OUT Pr /SDI OUT Y/ VIDEO OUT 1.
19 Connections $ Head connector panel The camera and lens control cables are connected to this panel. 1 ND/EXT connector This is for controlling the ND filter and lens extender of the power lens unit. Connect it when using a power lens unit equipped with an ND filter and lens extender function.
20 Connections $ Connecting the base connector panel 5 1394 connector This is for controlling the convertible camera, in which an IEEE 1394 card (AW-PB310), etc. has been installed, and the pan-tilt head. As the connecting cable, use an IEEE 1394 cable.
21 G/L I N Pb OUT Pr /SDI OUT Y/VI DEO OUT 1394 CONTROL IN IP/RP DC12V IN CAMERA I/F LENSE I/F ND/EXT SDI IN CS O P +- LAMP CONTROL < ; = Connections $ Connecting the A C adapter f or use with the pan-tilt head Connect the pan-tilt head with the AW-PS300 AC adapter designed for use with the pan- tilt head.
22 ON OFF RET PB SDI PR WEB 1394 WEB RP422 Connections $ Setting the printed circuit boar d s witches O Analog settings SDI/PR switch : Pr WEB/1394 switch : 1394 WEB/RP422 switch : RP422 O SDI setting.
O I CONTROL OUT T O P AN/TIL T HEAD VIDEO/Y IN G/L OUT VIDEO IN VIDEO/Y OUT Y/VIDEO OUT G/L IN CONTRT OL IN IP/RP REMOTE Examples of connections 1. When controlling the camera and pan-tilt head using .
24 O I REMOTE VIDEO/Y IN Pr IN Pb IN G/L OUT Y IN Pr IN Pb IN VIDEO/Y OUT Pr OUT Pb OUT CONTROL IN IP/RP Y/VIDEO OUT Pr/SDI OUT Pb OUT G/L IN CONTROL OUT T O P AN/TIL T HEAD Examples of connections 2.
25 SDI IN Pr/SDI OUT O I REMOTE CONTROL OUT T O P AN/TIL T HEAD G/L IN G/L OUT CONTROL IN IP/RP Examples of connections 3. When controlling the camera and pan-tilt head using the AW-RP605 multi-functi.
26 O I CONTROL IN IP/RP Examples of connections 4. When connecting a pan-tilt head through a network and controlling the camera and pan-tilt head using a personal computer Personal computer (Windows) .
27 O I CONTROL IN IP/RP RS-422 RS-232C Y/VIDEO OUT VIDEO IN Examples of connections 5. When controlling the camera and pan-tilt head using a personal computer, etc.
28 Examples of connections 6. When controlling the camera and pan-tilt head using a personal computer, etc. and transmitting component signals O I CONTROL IN IP/RP RS-422 RS-232C Y/VIDEO OUT Pr/SDI OU.
29 Limiters Be absolutely sure to set the limiters (travel range) of the pan/tilt head before use. Depending on where the pan/tilt head system has been installed, obstacles may be present within the travel range with which the camera may come into contact.
30 Limiters O Setting the left-most limit position of the travel range 1. Using the controller, rotate the camera to the position which is to serve as the left-most limit. 2. While holding down the OK button on the controller, press TRACING/PRESET MEMORY button 44 .
31 Limiters $ Releasing the limiters A limiter position which has been set can be released by following the steps below. O Releasing the upper limit position setting of the travel range 1. While holding down the OK button on the controller, press TRACING/PRESET MEMORY button 47 .
32 Replacement of consumable parts O Replacing the battery The battery lasts for about 5 years. The pan-tilt head stores the present positions, limiter positions and other data in its memory.
33 Specifications Power supply: DC +12 V (connector) Power consumption: DC +12 V 2.5 A (camera power included), DC +12 V 0.7 A (pan-tilt head only) Genlock input Black burst or composite video, 1 V [p-p]/75 Ω (BNC connector) Camera video output Composite video: 1 V [p-p]/75 Ω Component video: Y = 1 V [p-p]/75 Ω Pr = 0.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 EASTERN ZONE: .
デバイスPanasonic AW- PH350の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic AW- PH350をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic AW- PH350の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic AW- PH350の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic AW- PH350で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic AW- PH350を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic AW- PH350の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic AW- PH350に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic AW- PH350デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
