PanasonicメーカーAW-HB505の使用説明書/サービス説明書
ページ先へ移動 of 28
Multiport Hub A W -HB505 Before attempting to connect or operate this product, please read these instructions completely. .
Warning: This equipment generates and uses radio frequency ener - gy and if not installed and used properly, i.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications.
-1- CONTENTS FEATURES .................................................................................................................................................................................. 2 PRECAUTIONS ....................................
-2- FEA TURES • The Multiport Hub AW-HB505 is combined with the Multi-Hybrid Control Panel (AW-RP505) to control up to five Pan/tilt Heads (AW-PH300) and Color Video Cameras (AW-E560).
-3- • Use only with AC Adaptor, Model AW-PS505. • Handle the control panel with care. Dropping the control panel or subjecting it to a strong shock can cause a failure or an accident.
-4- MAJOR OPERA TING CONTROLS AND THEIR FUNCTIONS POWER 1 YC 2 YC 3 YC 4 YC 5 YC OFF ON CABLE COMP Multl Port Hub A W-H8505 ■ FRONT P ANEL q Power Indicator [POWER] Lights red when Power ON/OFF Switch w is in the ON position, and goes out when the same switch is set to the OFF position.
-5- e Cable Compensation Luminance Control [CABLE COMP Y] Used to adjust the Y (luminance) signal level of video output signals as appropriate to the length of the cable between the pan/tilt head and the Multiport Hub.
-6- CAMERA CONTROL OUT CAMERA CONTROL IN VIDEO OUT PAM/TIL T CONTROL OUT PAM/TIL T CONTROL IN S-VIDEO OUT VIDEO IN G/L OUT G/L IN CAMERA CONTROL OUT VIDEO OUT PAM/TIL T CONTROL OUT S-VIDEO OUT VIDEO I.
-7- o Camera Control Input Connector [TO CONTROL PANEL, CAMERA CONTROL IN] Connect it to Camera Control Input Connector [CAM- ERA CONTROL OUT] on the multi hybrid control panel with a coaxial straight cable (5C-2V or equivalent), which may be extended up to 10 meters.
-8- • Install the pan/tilt head after carefully reading the Operating Instructions for Pan/tilt Head. • Have four hex bolts (M6 x 4) ready for mounting the pan/title head. Select bolts of a length appropriate to the material and structure of the mounting base and the overall weight applied to it.
-9- • Changing Switch Settings on Pan/tilt Head q Remove the cover from the pan/tilt head. * Be careful of the Tally Indicator wire. w Shift the mounting direction switches (SW1, SW2) on the pan/tilt head depending on whether the head is suspended from the ceiling or mounted on the floor.
-10- ON OFF • Shifting Cable Compensation Switch on Pan/tilt Head If the distance from the control panel to the pan/tilt head is longer than 300 meters, set the cable compen- sation switch to the ON position by observing the fol- lowing procedure. q Remove the controller connection panel from the pan/tilt head.
-11- CONNECTION • Before making any connection, switch off all the com- ponents of the system. • Use the Control Panel AC Adaptor AW-PS301 (optional) and Pan/tilt Head AC Adaptor AW-PS300 (optional). • Use the Pan/tilt Head AW-PH300 and the Color Video Camera WV-E550 or AW-E560.
-12- ITEM (AWC) UP (ABC) PAGE DOWN (BAR) IRIS G/L IN VIDEO OUT ZOOM/FOCUS REMOTE VD VIDEO/RGB VBS/HD 75 ON OFF CONTROL EXT DC IN SEE MANUAL CAUTION • Connect the iris control cable of the motor-driven zoom lens to the camera and the remote (zoom/focus control) cable to the pan/tilt head.
-13- CAMERA CONTROL OUT CAMERA CONTROL IN VIDEO OUT PAM/TILT CONTROL OUT PAM/TILT CONTROL IN S-VIDEO OUT VIDEO IN G/L OUT G/L IN CAMERA CONTROL OUT VIDEO OUT PAM/TILT CONTROL OUT S-VIDEO OUT VIDEO IN .
-14- S-VIDEO VIDEO PREVIEW VIDEO VIDEO CONTACT PAN/TILT CONTROL PAN/TILT CONTROL CAMERA CONTROL CAMERA CONTROL SYSTEM TALLY G/L G/L DC-15V OPTION SWITCH CONTROL PREVIEW VIDEO G/L ON POWER OFF POWER O I FUSE(POWER) 3.15A FUSE FUSE Option Unit SEG, Switcher etc.
MEMORY PRESET 2 13 4 5 6 789 1 0 -15- OPERA TION 1. Power Set the power switches on the pan/tilt head AC adapter and the multiport hub AC adapter to the ON position, then set Power control Switch on the multi control panel to the ON position.
-16- e Right Panning Limiter Turn the pan/tilt head to the desired right panning limit with PAN/TILT Lever of the multi hybrid control panel, keep MEMORY Switch depressed, and simultaneously press buttons [4] and [9] of PRESET Switch for 5 sec- onds or more.
-17- 2) Adjust the cable compensation, genlock, and total pedestal of the selected camera. • Cable Compensation Signal degradation due to cable length between the con- trol panel and the pan/tilt head can be compensated for.
-18- GRAY YELLOW CYAN GREEN MAGENTA RED BLUE 100 90 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 +69 +77 +56 +48 +38 +12 +7 -5 -16 -16 +15 +28 +36 +20 -20 +20 -20 +100+100 +89 +77 +72 +46 IRE 75% 100% 1V[p-p] +100 +27 +27 -20 -13 -13 100 90 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 IRE 75% 100% +20 -20 +20 -20 +7.
-19- e Set G/L PHASE ON/OFF Switch of the multi hybrid con- trol panel back to the OFF position. • Subcarrier Phase Adjustment q Set G/L PHASE ON/OFF Switch (15) of the multi hybrid control panel to the ON position.
-20- • T otal Pedestal Adjustment Total pedestal adjustment is made to adjust the pedestals of two or more cameras. Using an oscillo- scope or a waveform monitor, adjust the pedestals to 5 IRE (0.035 V) or 7.5 IRE (0.050 V) with T.PED Control of the multi hybrid control panel.
-21- w Pick up a white object (a white wall or white handker- chief, for example) fully on the screen. Be careful to keep a shiny or bright object out of the screen. e When AWC Switch of the multi hybrid control panel is pressed, the auto Auto set Indicator flashes and the white balance is automatically adjusted.
-22- 5. Camera and Pan/tilt Head Presetting 1) Select a camera and pan/tilt head with the CONTROL switch on the multi hybrid control panel. 2) Pick up a desired object with the camera using PAN/TILT Lever ZOOM Lever and FOCUS Lever of the multi hybrid control panel.
1 YC 2 YC 3 YC 4 YC 5 YC CABLE COMP 1 YC 2 YC 3 YC 4 YC 5 YC CABLE COMP 1 YC 2 YC 3 YC 4 YC 5 YC CABLE COMP -23- RACK MOUNTING To mount the multiport hub in a rack, use the supplied rack mounting brackets and screws (M4x10). q Press the power switch to turn power off.
-24- SPECIFICA TIONS Source Voltage 12 V DC (4-pin cannon connector) Power Consumption 12V, 2A Video Input 1.0 V[p-p] composite/75 Ω x 5 (BNC connector) Genlock Input 1.0 V[p-p] black burst/75 Ω (BNC connector) Camera Control Intput Control signal (BNC connector) Pan/tilt Control Intput Control signal (RJ-45 8P modular jack) Video Output 1.
-25- Operating temperature − 10°C to +45°C (14°F to +113°F) Dimensions 420 (W) x 88 (H) x 250 (D) mm [16-9/16" (W) x 3-7/16" (H) x9-13/16” (D)] Weight 4 kg (8.8 lbs.) Finish Cover: AV Ivory vinyl chloride steel Panel: AV Ivory painting Weight and dimensions indicated are approximate.
N1197-0 7J1A108A Printed in Japan Broadcast & Television Systems Company Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 2E-6, Secaucus, NJ 07094 Regiona.
デバイスPanasonic AW-HB505の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic AW-HB505をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic AW-HB505の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic AW-HB505の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic AW-HB505で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic AW-HB505を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic AW-HB505の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic AW-HB505に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic AW-HB505デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
