PanasonicメーカーAW-PB309Pの使用説明書/サービス説明書
ページ先へ移動 of 20
AW- P WEB car d RST LINK/RX 10BASE – T RS232C RD Y Before attempting to connect, operate or adjust this product, please read these instructions completely.
2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
3 Contents Introduction ....................................................................................................... 3 Precautions for use .......................................................................................... 3 Before use .
4 P ar ts and their functions 1 RST: Initial reset switch When this switch is held down for 3 or more seconds, the settings can be reset to the factory settings. It is capable of initializing the IP address and canceling the password. 2 RDY: Ready LED When this is lighted, it means that the card is operating normally.
5 Installation Ask your dealer to install the card in the camera. Bear in mind the following points when installing the card. ≥ Be absolutely sure to ask your dealer to install the card. ≥ Before installing the card, disconnect the camera’s power supply.
6 System upgrading O I [1] Connections An example of the basic connections is presented below. [2] Recommended system requirements 1) Personal computer Provide a Windows-compatible personal computer (.
7 System upgrading 1 Right click on the desktop’s My Network icon, and open Properties. 2 Select “TCP/IP” under the Network Settings tab, and click the Properties button. 3 Now set the IP address and net mask. IP address : 192.168.1.100 Net mask : 255.
8 System upgrading 1. Start up the browser. 2. Input the following address into the browser. http://192.168.1.50/config/config.html 3. A setting screen such as the one shown in the figure below now appears. Input the addresses. 4. Upon completion of the input, press the button at the bottom of the setting screen.
9 Image displa y method When this address is input, an image such as the one shown in Fig. 1 appears. (The image is a sample.) HIGH is set for the image quality and VGA (640 a 480) is set for the size in the initial status. To change the image quality or size, click the button under the image.
10 Config screen A number of different settings can be performed on the Config screen. 1 . Start up the browser. 2. Input the following address into the browser. http://(new IP address setting)/config/config.html The following address is used in the factory setting status: http://192.
11 Config screen 1 Network Set the IP address, net mask and gateway address in the fields provided here. Consult your network administrator for details on the addresses. After setting the information, you must click the 4 button. Bear in mind that the settings will not take effect unless this button is clicked.
12 P ass wor ds Three kinds of passwords can be set for the WEB card so that three levels of access restriction can be established. 1) Monitor password 2) Operation password 3) Management password Types of passwords Each password serves to restrict the kinds of operations that a user can perform.
13 P ass wor ds 3) Management password This is used to restrict access to the Config screen. The following window appears when the Config screen has been accessed. Input “management” into the user name field, and input the password which was set on the Config screen into the password field.
14 P ass wor ds The following anomalies do not indicate that something is wrong with the WEB card. What kind of window appears differs according to the type and version of the browser used. The following anomalies may appear due to the characteristics of the browser but they do not indicate that something is wrong with the WEB card.
15 External dimensions dra wing RST LINK/RX 10BASE – T RS232C RD Y 70 21.5 92 P an/tilt head and camera contr ol The pan/tilt head and camera can be controlled from the WEB card. ≥ The pan/tilt head that can be connected is the AW-PH350. (A dedicated software cable is required.
16 Bef ore requesting ser vice Item Power Checkpoint Is the RDY LED lighted? Status No Remedial action 1 Check whether the power adapter has been connected properly. 2 Check whether the camera’s power LED is lighted. 3 Check whether the WEB card has been correctly installed in the camera.
17 Specifications and accessories Dimensions (W a H a D) : 3-5/8˝ a 2-3/4˝ a 7/8˝ (92 a 70 a 21.5 mm) Weight : 0.22 lbs (100 g) Image compression system : JPEG Image quality : 3-level setting Screen size : 640 a 480, 320 a 240, 640 a 240 Image updating interval : 15 images/sec.
18.
19.
F0901T2012 @ Printed in Japan VQT9458-1 PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W.
デバイスPanasonic AW-PB309Pの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic AW-PB309Pをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic AW-PB309Pの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic AW-PB309Pの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic AW-PB309Pで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic AW-PB309Pを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic AW-PB309Pの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic AW-PB309Pに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic AW-PB309Pデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
