AsusメーカーP4B266の使用説明書/サービス説明書
ページ先へ移動 of 128
Motherboard ® P4B266 User Guide.
ii Checklist Copyright © 2002 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, sto.
iii Features Contents FCC/CDC statements ..................................................................... vi Safety information .......................................................................... vi i About this guide .....................
iv Safeguards Contents 2.6 Expansion slots ................................................................. 2-13 2.6.1 Installing an expansion card .................................. 2-13 2.6.2 Configuring an expansion card ..........................
v Contents Chapter 5: Software support ............................................... 5- 1 5.1 Install an operating system .................................................. 5 -1 5.2 Support CD information ............................................
vi FCC/CDC st atements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide This user guide contains the information you need when installing the ASUS P4B266 motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the P4B266 motherboard.
ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates.
x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.
Chapter 1 This chapter describes the features of the P4B266 motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide 1-1 1 . 1 Welcome! Thank you for buying the ASUS ® P4B266 motherboard! The ASUS P4B266 motherboard is basically an ASUS P4B266 motherboard – minus some onboard features including USB 2.0, LAN, POST Reporter ™ , and Memory Stick/Secure Digital interfaces.
1-2 Chapter 1: Product introduction 1 .3 Special features 1.3.1 Product highlights Latest processor technology The P4B266 motherboard supports the latest Intel Pentium 4 478/ Northwood Processor , also known as P4, via a 478-pin surface mount ZIF socket.
ASUS P4B266 motherboard user guide 1-3 1.3.2 V alue-added solutions Overclocking The P4B266 overclocking features: • adjustable CPU frequency multiple in BIOS using the ASUS JumperFree ™ solution .
1-4 Chapter 1: Product introduction 1 .4 Over view Before you install the P4B266 motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades.
ASUS P4B266 motherboard user guide 1-5 23 4 19 14 1 1 16 18 17 1 12 5 6 15 13 10 9 8 7 20 21 22 23 24 25 28 26 27.
1-6 Chapter 1: Product introduction A TX 12V connector . This power connector connects the 4-pin 12V plug from the A TX 12V power supply . CPU socket. A 478-pin surface mount, Zero Insertion Force (ZIF) socket called mPGA478 B. This socket accommodates the Intel ® Pentium ® 4 478/Northwood Processor with 400MHz system bus.
ASUS P4B266 motherboard user guide 1-7 Super I/O controller . This Low Pin Count (LPC) interface provides the commonly used Super I/O functionality . The chipset supports a high-performance floppy disk controller for a 360K/720K/1.
1-8 Chapter 1: Product introduction PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse. Parallel port. This 25-pin port connects a parallel printer , a scanner , or other devices. Game/MIDI port. This connector supports a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files.
Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The P4B266 uses the A TX form factor that measures 12 inches x 9.
2-2 Chapter 2: Hardware information 2.2 Motherboard layout The audio features are optional. These components are grayed out in the above motherboard layout.
ASUS P4B266 motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component.
2-4 Chapter 2: Hardware information 2.4 Central Pr ocessing Unit (CPU) 2.4.1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. This socket is specifically designed for the Intel ® Pentium ® 4 478/Northwood Processor .
ASUS P4B266 motherboard user guide 2-5 2.4.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard.
2-6 Chapter 2: Hardware information 3. Position the CPU above the socket such that its marked corner matches the base of the socket lever . 4. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation.
ASUS P4B266 motherboard user guide 2-7 2.4.3 Installing the heatsink and fan The Intel ® Pentium ® 4 478/Northwood Processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. The retention module base is already installed on the motherboard upon purchase.
2-8 Chapter 2: Hardware information 2. Position the fan with the retention mechanism on top of the heatsink. Align and snap the four hooks of the retention mechanism to the holes on each corner of the module base. Keep the retention locks lifted upward while fitting the retention mechanism to the module base.
ASUS P4B266 motherboard user guide 2-9 2.4.4 Connecting the CPU fan cable When the fan, heatsink, and the retention mechanism are in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN. 3. Push down the locks on the retention mechanism to secure the heatsink and fan to the module base.
2-10 Chapter 2: Hardware information 2.5 System memor y 2.5.1 Overview The motherboard comes with three Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 2GB system memory using 184-pin unbuffered ECC or non-ECC PC2100/1600 DIMMs.
ASUS P4B266 motherboard user guide 2-11 2.5.2 Memory configurations 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
2-12 Chapter 2: Hardware information 2.5.4 Removing a DIMM Follow these steps to remove a DIMM. 1. Simultaneously press the retaining clips outward to unlock the DIMM. Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
ASUS P4B266 motherboard user guide 2-13 2.6 Expansion slots In the future, you may need to install expansion cards. The motherboard has six PCI slots, one Accelerated Graphics Port (AGP) slot, and a Communications and Networking Riser (CNR) slot. The following sub- sections describe the slots and the expansion cards that they support.
2-14 Chapter 2: Hardware information Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port (CO.
ASUS P4B266 motherboard user guide 2-15 2.6.3 PCI slots There are six 32-bit PCI slots in this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot.
2-16 Chapter 2: Hardware information 2.6.5 CNR slot The Communications and Networking Riser (CNR) slot supports interface cards that integrates audio, modem, and network functionality .
ASUS P4B266 motherboard user guide 2-17 2.7 Switches and jumper s The motherboard frequency is adjusted through the DIP switches. The white block represents the switch position. The illustration below shows all the switches in the OFF position. The JEN jumper is set in conjunction with the DIP switches.
2-18 Chapter 2: Hardware information 2. CPU Core:Bus frequency multiple (SWITCH Switches 1-4) This option sets the frequency multiple between the CPU internal and external frequencies. This must be set in conjunction with the CPU Bus Frequency . Make sure that the JEN jumper is set to jumper mode before setting the above switches.
ASUS P4B266 motherboard user guide 2-19 3. CPU frequency selection (SWITCH Switches 5-9) This option tells the clock generator what frequency to send the CPU.
2-20 Chapter 2: Hardware information 4. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar).
ASUS P4B266 motherboard user guide 2-21 6. USB device wake-up (3-pin USBPWR01, USBPWR23) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices.
2-22 Chapter 2: Hardware information 7. VCORE over-voltage (3-pin OVER_VOL T) When enabled, this jumper allows a CPU Vcore setting range of +1.75V to +2.1V for Pentium 4 Willamette processor , and a 1.50V to 1.75V range for Northwood processor through BIOS Setup.
ASUS P4B266 motherboard user guide 2-23 9. Bass/Center setting (3-pin BCS1, BCS2) (on audio models only) These jumpers allow you to select the speaker output for a 6-channel audio system.
2-24 Chapter 2: Hardware information 10. Clear RTC RAM (CLRTC) These solder points allow you to clear the Real T ime Clock (R TC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
ASUS P4B266 motherboard user guide 2-25 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout.
2-26 Chapter 2: Hardware information 2. IDE connectors (40-1 pin PRIMAR Y IDE/SECONDAR Y IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable.
ASUS P4B266 motherboard user guide 2-27 3. Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug).
2-28 Chapter 2: Hardware information 5. ASUS EZ Plug ™ and A TX power connectors (20-pin A TXPWR, 4-pin A TX+12V , 4-pin AUX+12V) These connectors connect to an A TX 12V power supply . The plugs from the power supply are designed to fit these connectors in only one orientation.
ASUS P4B266 motherboard user guide 2-29 6. CPU, Chassis, and Power Fan Connectors (3-pin CPU_F AN, PWRF AN, CH_F AN) The three fan connectors support cooling fans of 350mA (4.2 W atts) or a total of 1A (12W) at +12V . Orient the fans so that the heat sink fins allow air flow to go across the onboard heat sinks instead of the expansion slots.
2-30 Chapter 2: Hardware information 8. SMBus connector (6-1 pin SMB) This connector allows you to connect SMBus (System Management Bus) devices. Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface.
ASUS P4B266 motherboard user guide 2-31 10. Line in connector (5-pin LINE_IN) (optional) This connector is for a front panel Line In jack with a return path for automatic signal switching.
2-32 Chapter 2: Hardware information 12. ASUS iPanel connector (24-1 pin AFP ANEL) (optional) This connector allows you to connect an optional ASUS iPanel, an easy-to-access drive bay with front I/O ports and status LEDs.
ASUS P4B266 motherboard user guide 2-33 14. Infrared module connector (two 5-1 pin IR) This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system chassis that support this feature.
2-34 Chapter 2: Hardware information 16. System panel connector (20-pin P ANEL) This connector accommodates several system front panel functions. • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
ASUS P4B266 motherboard user guide 2-35 • A TX Power Switch / Soft-Off Switch Lead (2-pin PWRBTN) This connector connects a switch that controls the system power . Pressing the power switch turns the system between ON and SLEEP , or ON and SOFT OFF , depending on the BIOS or OS settings.
2-36 Chapter 2: Hardware information.
Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes..
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide 3-1 3. 1 St ar ting up for t he firs t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
3-2 Chapter 3: Powering up 3.2 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system.
Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide 4-1 4. 1 Managing and updating your BIOS 4.1.1 Using the computer system for the first time It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later .
4-2 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears.
ASUS P4B266 motherboard user guide 4-3 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3. At the “ A: ” prompt, type AFLASH and then press <Enter>.
4-4 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears.
ASUS P4B266 motherboard user guide 4-5 4.2 BIOS Setup progr am This motherboard supports a programmable EEPROM that you can update using the provided utility described in section “ 4.
4-6 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features.
ASUS P4B266 motherboard user guide 4-7 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination.
4-8 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59).
ASUS P4B266 motherboard user guide 4-9 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu.
4-10 Chapter 4: BIOS Setup If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM drives [LS-120].
ASUS P4B266 motherboard user guide 4-11 T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors.
4-12 Chapter 4: BIOS Setup SMART Monitoring [Disabled] This field allows you to enable or disable the S.M.A.R.T . (Self-Monitoring, Analysis and Reporting T echnology) system that utilizes internal hard disk drive monitoring technology .
ASUS P4B266 motherboard user guide 4-13 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Of f] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes.
4-14 Chapter 4: BIOS Setup Language [English] This field displays the BIOS language version. Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>.
ASUS P4B266 motherboard user guide 4-15 4.4 Advanced Menu CPU Speed [Manual] When the motherboard is set to JumperFree ™ mode, this field allows you to select the internal frequency of the CPU. Select [Manual] if you want to make changes to the two subsequent fields.
4-16 Chapter 4: BIOS Setup CPU VCore Setting [Auto] The [Manual] setting allows you to manually select the core voltage supplied to the CPU (see next item). However , it is recommended that you keep the default setting [Auto] to allow the system to automatically determine the appropriate CPU core voltage.
ASUS P4B266 motherboard user guide 4-17 PS/2 Mouse Function Control [Auto] The default setting [Auto] allows the system to detect a PS/2 mouse at startup. If a mouse is detected, the BIOS assigns IRQ12 to the PS/2 mouse. Otherwise, IRQ12 can be used for expansion cards.
4-18 Chapter 4: BIOS Setup 4.4.1 Chip Configuration The DDR SDRAM CAS Latency parameter appears only when you set the SDRAM Configuration to [User Defined]. SDRAM RAS to CAS Delay [3T] This item controls the latency between the DDR SDRAM active command and the read/write command.
ASUS P4B266 motherboard user guide 4-19 SDRAM Idle Timer [Infinite] Configuration options: [Infinite] [0T] [8T] [16T] [64T] Optimization Mode [Normal] This parameter allows you to enhance system performance and overclocking capability when set to [T urbo 1] or [T urbo 2].
4-20 Chapter 4: BIOS Setup V ideo Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor .
ASUS P4B266 motherboard user guide 4-21 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive.
4-22 Chapter 4: BIOS Setup Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] al.
ASUS P4B266 motherboard user guide 4-23 Slot 1/5, Slot 2, Slot 3, Slot 4, Slot 6 IRQ [Auto] These fields automatically assign the IRQ for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ assignments.
4-24 Chapter 4: BIOS Setup IRQ XX Reserved [No/ICU] These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. The setting [No/ICU] for an IRQ field indicates that you are using the ISA Configuration Utility (ICU), and that this particular IRQ is NOT required by a legacy ISA card.
ASUS P4B266 motherboard user guide 4-25 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features.
4-26 Chapter 4: BIOS Setup V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features.
ASUS P4B266 motherboard user guide 4-27 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption.
4-28 Chapter 4: BIOS Setup Power On By PS/2 Keyboard [Space Bar] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an A TX power supply that provides at least 1A on the +5VSB lead.
ASUS P4B266 motherboard user guide 4-29 4.5.2 Hardware Monitor MB T emperature [xxxC/xxxF] CPU T emperature [xxxC/xxxF] POWER T emperature [xxxC/xxxF] The onboard hardware monitor automatically detects the motherboard and CPU temperatures.
4-30 Chapter 4: BIOS Setup Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or <Space> key , you can promote devices and by using the <-> key , you can demote devices.
ASUS P4B266 motherboard user guide 4-31 Other Boot Device Select [INT18 Device (Network)] Configuration options: [Disabled] [SCSI Boot Device] [INT18 Device (Network)] Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS.
4-32 Chapter 4: BIOS Setup Interrupt Mode [APIC] The Advanced Programmable Interrupt Controller (APIC) setting allows you to distribute interrupt routings other than the 16 IRQs. The Programmable Interrupt Controller (PIC) setting allows you to use the 16 IRQs only .
ASUS P4B266 motherboard user guide 4-33 4.7 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup.
4-34 Chapter 4: BIOS Setup Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values.
Chapter 5 Software support This chapter describes the contents of the support CD that comes with the motherboard package..
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide 5-1 5. 1 Inst all an operating system This motherboard supports Windows 98/ME/NT/2000/XP and OS/2 operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.
5-2 Chapter 5: Software support 5.2.2 Main menu From the welcome screen, the program takes you directly to the main menu. The main menu displays an image of the motherboard, and the buttons and icons that link you to the software, drivers, utilities, and other information contained in the support CD.
ASUS P4B266 motherboard user guide 5-3 5.2.3 Software menu The software menu shows the applications and other software that the motherboard supports. The highlighted items indicate that they are available for your motherboard. Simply click on a specific item then follow the installation wizard to install it.
5-4 Chapter 5: Software support ASUS BIOS Flash Utility This utility allows you to remotely flash the Client PC’s BIOS when used with the Intel LDCM Administrator . ASUS PC Probe This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you on any detected problems.
ASUS P4B266 motherboard user guide 5-5 5.2.4 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices.
5-6 Chapter 5: Software support 5.2.6 ASUS Contact Information Clicking the ASUS Contact Information button displays as stated. Y ou may also find this information on page x of this user guide. 5.2.5 DOS Utility menu The DOS utility menu allows you to use the Flash BIOS Utility under DOS mode.
ASUS P4B266 motherboard user guide 5-7 5.2.7 Other information The icons on the left side of the screen give additional information on the motherboard and the contents of the support CD. This section shows the pop-up windows that appear when you click the icons.
5-8 Chapter 5: Software support T echnical Support Form The window displays the ASUS T echnical Support Request Form that you have to fill up when requesting technical support. Readme The window displays the contents of the support CD and a brief description of each in text format.
ASUS P4B266 motherboard user guide 5-9 5.3 Softwar e information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information.
5-10 Chapter 5: Software support 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file.
ASUS P4B266 motherboard user guide 5-11 4. From the selection that appears, choose a logo image. Click Next. NOTE: If you wish, you may create your own boot logo image in GIF , JPG, or BMP file formats. 6. The next screen prompts you to flash the original BIOS to update it with the new boot logo.
5-12 Chapter 5: Software support 5.3.3 Multi-Channel Audio Feature The C-Media PCI Audio Driver and Applications are included in the Support CD that came with your motherboard package.
ASUS P4B266 motherboard user guide 5-13 The functions of the Line Out (lime), Line In (blue), and Mic (pink) connectors on the rear panel change when you select the 6-channel audio configuration.
5-14 Chapter 5: Software support.
Glossary This part lists the technical terms that you may encounter when reading this document..
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide G-1 AC’97 (Audio Codec '97). AC '97 is the next step in enabling PCs with audio quality comparable to consumer electronics devices.
G-2 Glossary BIOS (Basic Input/Output System). BIOS is a set of routines that control how the computer transfers data between computer components, such as memory , disks, and the display adapter . The BIOS instructions are built into the computer ’s read-only memory .
ASUS P4B266 motherboard user guide G-3 Device Driver . A software routine that links a peripheral device to the operating system. It acts as a translator between the device and the applications that use it.
G-4 Glossary IrDA (Infrared Data Association). An internaltional organization that creates and promotes inter-operable, low cost, infrared data interconnection standards that support a walk-up, point-to-point model.
ASUS P4B266 motherboard user guide G-5 POST (Power On Self T est). When you turn ON the computer , it will first run through the POST , a series of software-controlled diagnostic tests. The POST checks system memory , the motherboard circuitry , the display , the keyboard, the diskette drive, and other I/O devices.
G-6 Glossary System Disk. A system disk contains the core file of an operating system and is used to boot up the operating system. TCP/IP (T ransmission Control Protocol/Internet Protocol). The communications protocol used by the UNIX system and the Internet.
Index This part contains an alphabetical list of the topics found in this document..
ASUS P4B266 motherboard.
ASUS P4B266 motherboard user guide I-1 A Accelerated Graphics Port 2-15 Acrobat Reader 5-4 ASUS ASIC 1-7 ASUS EZ Plug ™ 1-2, 1-6, 2-28 ASUS iPanel 1-3, 2-30 ASUS MyLogo ™ 1-2, 5-10 ASUS PC Probe 5.
I-2 Index E Expansion card installation 2-13 configuration 2-14 Expansion slots 1-7, 2-13 AGP 1-7 CNR 1-7 PCI 1-7 F Flash EEPROM 1-7 Floppy 3 Mode 4-8 H Hard Disk Drives (HDDs) CHS Capacity 4-1 1 Cyli.
ASUS P4B266 motherboard user guide I-3 PS/2 Keyboard Port 1-8 PS/2 Mouse Port 1-8 PS/2 Mouse Function Control 4-17 R R TC RAM clearing 2-24 S SDRAM Active Precharge Delay 4-19 CAS Latency 4-18 Configu.
I-4 Index.
デバイスAsus P4B266の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Asus P4B266をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsus P4B266の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Asus P4B266の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Asus P4B266で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Asus P4B266を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsus P4B266の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Asus P4B266に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsus P4B266デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。