AsusメーカーP4B533の使用説明書/サービス説明書
ページ先へ移動 of 140
Motherboard P4B533 User Guide.
ii Checklist Copyright © 2002 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, sto.
iii Features Contents Contents ......................................................................................... iii FCC/CDC statements ..................................................................... vi Safety information ...............
iv Safeguards Contents 2.6 Expansion slots ................................................................ 2-13 2.6.1 Installing an expansion card ................................ 2-13 2.6.2 Configuring an expansion card ............................ 2-13 2.
v Contents Chapter 5: Software support 5.1 Install an operating system ................................................. 5-1 5.2 Support CD information ...................................................... 5-1 5.2.1 Running the support CD ...........
vi FCC/CDC st atements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide This user guide contains the information you need when installing the ASUS P4B533 motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the P4B533 motherboard.
ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates.
x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.
xi P4B533 specifications summar y CPU Chipset Front Side Bus (FSB) Memory Expansion slots IDE Audio (optional) Special features Rear panel I/O Internal I/O BIOS features Socket 478 for Intel ® Pentiu.
xii Industry standard Manageability Form Factor Support CD contents PCI 2.2, USB 2.0 WfM 2.0. DMI 2.0, WOL/WOR by PME, chassis intrusion, SMBus A TX form factor: 12 in x 8.
Chapter 1 This chapter describes the features of the P4B533 motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
ASUS P4B533 motherboard Chapter summar y 1.1 W elcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features ............................................. 1-2 1.
ASUS P4B533 motherboard user guide 1-1 1 . 1 Welcome! Thank you for buying the ASUS ® P4B533 motherboard! The ASUS P4B533 motherboard delivers a host of new features and latest technologies making it.
1-2 Chapter 1: Product introduction 1 .3 Special features 1.3.1 Product highlights Latest processor technology The P4B533 motherboard supports the latest Intel ® Pentium ® 4 Processor via a 478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2 cache on 0.
ASUS P4B533 motherboard user guide 1-3 ASUS EZ Plug ™ This patented ASUS technology lets you use your existing power supply rather than buying a new A TX 12V power supply . The ASUS EZ Plug ™ is a 4-pin auxillary +12V connector mounted on the motherboard that connects a regular 4-pin device power connector from the power supply .
1-4 Chapter 1: Product introduction 1.3.2 V alue-added solutions Overclocking The P4B533 overclocking features: • adjustable CPU frequency multiple in BIOS using the ASUS JumperFree ™ solution •.
ASUS P4B533 motherboard user guide 1-5 Dual function power switch While the system is ON, pressing the power switch for less than 4 seconds puts the system to sleep mode or to soft-of f mode, depending on the BIOS setting. Pressing the power switch for more than 4 seconds lets the system enter the soft-of f mode regardless of the BIOS setting.
1-6 Chapter 1: Product introduction 1 .4 Motherboard over view Before you install the P4B533 motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades.
ASUS P4B533 motherboard user guide 1-7 20 21 28 27 26 25 22 23 24 56 19 14 15 2 18 9 7 8 10 13 12 16 3 4 11 17 1.
1-8 Chapter 1: Product introduction ASUS EZ Plug ™ +12V connector . This ASUS patented auxilliary power connector is used if you don ’ t have an A TX +12V power supply . Connect a 4-pin device connector from a standard power supply to this connector to provide sufficient power to the CPU.
ASUS P4B533 motherboard user guide 1-9 IDE connectors. These dual-channel bus master IDE connectors support up to four Ultra DMA/100/66, PIO Modes 3 & 4 IDE devices. Both the primary (blue) and secondary (black) connectors are slotted to prevent incorrect insertion of the IDE ribbon cable.
1-10 Chapter 1: Product introduction PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse. Parallel port. This 25-pin port connects a parallel printer , a scanner , or other devices. Line In jack. This Line In (light blue) jack connects a tape player or other audio sources.
Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
ASUS P4B533 motherboard Chapter summar y 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) .
ASUS P4B533 motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The P4B533 uses the A TX form factor that measures 12 inches x 8.
2-2 Chapter 2: Hardware information 2.2 Motherboard layout The audio features are optional. These components are grayed out in the above motherboard layout.
ASUS P4B533 motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component.
2-4 Chapter 2: Hardware information 2.4 Central Pr ocessing Unit (CPU) 2.4.1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. The socket is designed for the Intel ® Pentium ® 4 Processor in the 478-pin package with 512KB L2 cache on 0.
ASUS P4B533 motherboard user guide 2-5 2.4.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard. T o use the Hyper-Threading T echnology on this motherboard: 1. Buy an Intel Pentium 4 CPU that supports Hyper-Threading T echnology .
2-6 Chapter 2: Hardware information 3. Position the CPU above the socket such that its marked corner matches the base of the socket lever . 4. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation.
ASUS P4B533 motherboard user guide 2-7 2.4.3 Installing the heatsink and fan The Intel ® Pentium ® 4 Processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Retention Module Base CPU Heatsink The retention module base is already installed on the motherboard upon purchase.
2-8 Chapter 2: Hardware information 2. Position the fan with the retention mechanism on top of the heatsink. Align and snap the four hooks of the retention mechanism to the holes on each corner of the module base. Keep the retention locks lifted upward while fitting the retention mechanism to the module base.
ASUS P4B533 motherboard user guide 2-9 2.4.4 Connecting the CPU fan cable When the fan, heatsink, and the retention mechanism are in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN. 3. Push down the locks on the retention mechanism to secure the heatsink and fan to the module base.
2-10 Chapter 2: Hardware information 2.5 System memor y 2.5.1 Overview The motherboard comes with three Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 2GB system memory using 184-pin unbuffered ECC or non-ECC PC2100/1600 DIMMs.
ASUS P4B533 motherboard user guide 2-11 2.5.2 Memory configurations 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
2-12 Chapter 2: Hardware information 2.5.4 Removing a DIMM Follow these steps to remove a DIMM. 1. Simultaneously press the retaining clips outward to unlock the DIMM. Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
ASUS P4B533 motherboard user guide 2-13 2.6 Expansion slots In the future, you may need to install expansion cards. The motherboard has six PCI slots and one Accelerated Graphics Port (AGP) slot. The following sub-sections describe the slots and the expansion cards that they support.
2-14 Chapter 2: Hardware information Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port (CO.
ASUS P4B533 motherboard user guide 2-15 2.6.3 PCI slots There are six 32-bit PCI slots in this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot.
2-16 Chapter 2: Hardware information 2.7 Switches and jumpers The motherboard frequency is adjusted through the DIP switches. The white block represents the switch position. The illustration below shows the ON and OFF positions of the switches. The JEN jumper is set in conjunction with the DIP switches.
ASUS P4B533 motherboard user guide 2-17 2. CPU Core:Bus frequency multiple (DSW2 Switches 1-4) This option sets the frequency multiple between the CPU internal and external frequencies. This must be set in conjunction with the CPU Bus Frequency . Make sure that the JEN jumper is set to jumper mode before setting the above switches.
2-18 Chapter 2: Hardware information 3. CPU external frequency selection (DSW1 Switches 1-6) This option tells the clock generator what frequency to send the CPU.
ASUS P4B533 motherboard user guide 2-19 4. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar).
2-20 Chapter 2: Hardware information 6. USB device wake-up (3-pin USBPWR_12, USBPWR_34, USBPWR_56) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices.
ASUS P4B533 motherboard user guide 2-21 P4B533 ® P4B533 PCISMB Setting PCISMB_SW1 PCISMB_SW2 Disable Enable (Default) 12 2 3 P4B533 ® P4B533 Speaker Selector SPEECH LINEOUT BUZZER (Default) 12 2 3 7. Speaker selector (3-pin SPEECH) This jumper allows you to select the speaker you wish to use for the ASUS POST Reporter ™ function.
2-22 Chapter 2: Hardware information 10. Bass/Center setting (3-pin BCS1, BCS2) (on audio models only) These jumpers allow you to select the speaker output for a 6-channel audio system. Switch the jumpers from the CENTER/BASS (pins 1-2) position to BASS/CENTER (pins 2-3) position to re-route signals on the internal leads of the Mic port.
ASUS P4B533 motherboard user guide 2-23 1 1. PCI audio setting (3-pin AUDIO_SW) (on audio models only) This jumper allows you to enable or disable the audio controller on the motherboard. 12. Clear RTC RAM (CLRTC) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS.
2-24 Chapter 2: Hardware information 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the red stripe to Pin 1 on the connectors.
ASUS P4B533 motherboard user guide 2-25 3. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable.
2-26 Chapter 2: Hardware information 4. Chassis intrusion connector (4-1 pin CHASSIS) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch.
ASUS P4B533 motherboard user guide 2-27 6. ASUS EZ Plug™ and A TX power connectors (20-pin A TXPWR, 4-pin EZ_PLUG, 4-pin A TX12V) These connectors connect to an A TX 12V power supply . The plugs from the power supply are designed to fit these connectors in only one orientation.
2-28 Chapter 2: Hardware information 7. CPU, Chassis, and Power Fan Connectors (3-pin CPU_F AN, PWR_F AN, CHA_F AN) The fan connectors support cooling fans of 350mA~740mA (8.
ASUS P4B533 motherboard user guide 2-29 9. USB header (10-1 pin USB20_56) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 2.0 specification that supports up to 480 Mbps connection speed.
2-30 Chapter 2: Hardware information 1 1. Infrared module connector (5-pin IR) This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system chassis that support this feature. Y ou must also configure the UART2 Use As parameter in BIOS to set UART2 for use with IR.
ASUS P4B533 motherboard user guide 2-31 13. Internal audio connectors (4-pin CD1, AUX, MODEM) (on audio models only) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner , or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector .
2-32 Chapter 2: Hardware information 15. ASUS iPanel connector (24-1 pin AFP ANEL) (optional) This connector allows you to connect an optional ASUS iPanel, an easy-to-access drive bay with front I/O ports and status LEDs.
ASUS P4B533 motherboard user guide 2-33 P4B533 ® P4B533 Front Panel Audio Connector FP_AUDIO BLINE_OUT_L MIC2 Line out_R Line out_L BLINE_OUT_R NC MICPWR +5V A AGND 17.
2-34 Chapter 2: Hardware information • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes..
ASUS P4B533 motherboard Chapter summar y 3.1 Starting up for the first time .......................... 3-1 3.2 V ocal POST Messages ...................
ASUS P4B533 motherboard user guide 3-1 3. 1 St ar ting up for the fir s t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
3-2 Chapter 3: Powering up 3.2 V ocal POST Messages This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST Reporter ™ . This feature gives you vocal POST messages and alerts to inform you of system events and boot status.
ASUS P4B533 motherboard user guide 3-3 POST Message Action Y ou may disable the ASUS POST Reporter ™ in the BIOS setup. See section “ 4.4.2 I/O Device Configuration ” . No keyboard detected • Check your keyboard if properly connected to the purple PS/2 connector on the rear panel.
3-4 Chapter 3: Powering up 3.3 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system.
Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
ASUS P4B533 motherboard Chapter summar y 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-7 4.3 Main Menu .................................................... 4-10 4.4 Advanced Menu .
ASUS P4B533 motherboard user guide 4-1 4. 1 Managing and updating your BIOS It is recommended that you save a copy of the motherboard’s original BIOS to a bootable floppy disk in case you need to reinstall the original BIOS later .
4-2 Chapter 4: BIOS Setup 5. At the prompt, “ Please Enter File Name for NEW BIOS: _ ” , type in the BIOS file name that you downloaded from the ASUS website, then press <Enter>. EZ Flash will automatically access drive A to look for the file name that you typed.
ASUS P4B533 motherboard user guide 4-3 4.1.2 Using AFLASH to update the BIOS Creating a bootable disk AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4-4 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears.
ASUS P4B533 motherboard user guide 4-5 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3. At the “ A: ” prompt, type AFLASH and then press <Enter>.
4-6 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears.
ASUS P4B533 motherboard user guide 4-7 4.2 BIOS Setup progr am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 4.
4-8 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features.
ASUS P4B533 motherboard user guide 4-9 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination.
4-10 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59).
ASUS P4B533 motherboard user guide 4-11 Language [English US] This field allows you to choose the BIOS language version from the available options. Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>.
4-12 Chapter 4: BIOS Setup 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu.
ASUS P4B533 motherboard user guide 4-13 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM dr.
4-14 Chapter 4: BIOS Setup T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity .
ASUS P4B533 motherboard user guide 4-15 Multi-Sector T ransfers [Maximum] This option automatically sets the number of sectors per block to the highest number that the drive supports. Note that when this field is automatically configured, the set value may not always be the fastest value for the drive.
4-16 Chapter 4: BIOS Setup 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes.
ASUS P4B533 motherboard user guide 4-17 4.4 Advanced Menu CPU Speed [Manual] When the motherboard is set to JumperFree ™ mode, this field allows you to select the internal frequency of the CPU. Select [Manual] if you want to make changes to the two subsequent fields.
4-18 Chapter 4: BIOS Setup CPU/Memory Frequency Ratio [Auto] This field determines whether the memory clock frequency is set to be in synchronous or asynchronous mode with respect to the system frequency . The options that appear in the popup menu vary according to the CPU Frequency (MHz).
ASUS P4B533 motherboard user guide 4-19 Refer to the CPU documentation before setting this field. A very high core voltage may severely damage the CPU! CPU VCore [1.750V] (for W illamette) , [1.500V] (for Northwood) When the CPU VCore Setting parameter above is set to [Manual], the CPU VCore item allows you to select a specific CPU core voltage.
4-20 Chapter 4: BIOS Setup CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default [Enabled] or choose [Disabled] to turn on or off the CPU Level 1 and Level 2 built-in cache.
ASUS P4B533 motherboard user guide 4-21 4.4.1 Chip Configuration The SDRAM parameters (items 2~5) become configurable only when you set the SDRAM Configuration to [User Defined]. SDRAM CAS Latency [2.5T] This item controls the latency between the SDRAM read command and the time the data actually becomes available.
4-22 Chapter 4: BIOS Setup SDRAM RAS Precharge Delay [3T] This item controls the idle clocks after issuing a precharge command to the DDR SDRAM. It is recommended to keep the default setting for stable system operation. SDRAM Active Precharge Delay [6T] This item controls the number of DDR SDRAM clocks used for DDR SDRAM parameters.
ASUS P4B533 motherboard user guide 4-23 AGP Capability [4X Mode] This motherboard supports the AGP 4X interface that transfers video data at 1066MB/s. AGP 4X is backward-compatible, so you may keep the default [4X Mode] even if you are using an AGP 1X video card.
4-24 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes.
ASUS P4B533 motherboard user guide 4-25 Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction o.
4-26 Chapter 4: BIOS Setup Slot 1/5, Slot 2, Slot 3, Slot 4, Slot 6 IRQ [Auto] These fields automatically assign the IRQ for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ assignments.
ASUS P4B533 motherboard user guide 4-27 IRQ XX Reserved [No/ICU] These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card.
4-28 Chapter 4: BIOS Setup 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features.
ASUS P4B533 motherboard user guide 4-29 V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features.
4-30 Chapter 4: BIOS Setup 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption.
ASUS P4B533 motherboard user guide 4-31 Power On By PS/2 Keyboard [Disabled] This parameter allows you to use specific keys on the keyboard to turn on the system.
4-32 Chapter 4: BIOS Setup 4.5.2 Hardware Monitor MB T emperature [xxxC/xxxF] CPU T emperature [xxxC/xxxF] POWER T emperature [N/A] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures.
ASUS P4B533 motherboard user guide 4-33 If any of the monitored items is out of range, the following error message appears: “ Hardware Monitor found an error . Enter Power setup menu for details ” . Y ou will then be prompted to “ Press F1 to continue or DEL to enter SETUP ” .
4-34 Chapter 4: BIOS Setup Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or <Space> key , you can promote devices and by using the <-> key , you can demote devices.
ASUS P4B533 motherboard user guide 4-35 Other Boot Device Select [INT18 Device (Network)] Configuration options: [Disabled] [SCSI Boot Device] [INT18 Device (Network)] Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS.
4-36 Chapter 4: BIOS Setup 4.7 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup.
ASUS P4B533 motherboard user guide 4-37 Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values.
4-38 Chapter 4: BIOS Setup.
Chapter 5 Software support This chapter describes the contents of the support CD that comes with the motherboard package..
ASUS P4B533 motherboard Chapter summar y 5.1 Install an operating system ........................... 5-1 5.2 Support CD information ...................
ASUS P4B533 motherboard user guide 5-1 5. 1 Inst all an operating system This motherboard supports Windows ME/NT/2000/XP operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.
5-2 Chapter 5: Software support 5.2.2 Main menu From the welcome screen, the program takes you directly to the main menu. The main menu displays an image of the motherboard, and the buttons and icons that link you to the software, drivers, utilities, and other information contained in the support CD.
ASUS P4B533 motherboard user guide 5-3 5.2.3 Software menu The software menu shows the applications and other software that the motherboard supports. The highlighted items indicate that they are available for your motherboard. Simply click on a specific item then follow the installation wizard to install it.
5-4 Chapter 5: Software support Winbond V oice Editor This program is for recording and customizing wave files for the ASUS POST Reporter™. Use this program if you wish to change the default vocal POST messages. See section “3.2 V ocal POST messages” for a list of the default messages.
ASUS P4B533 motherboard user guide 5-5 5.2.4 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices.
5-6 Chapter 5: Software support 5.2.6 ASUS Contact Information Clicking the ASUS Contact Information button displays as stated. Y ou may also find this information on page x of this user guide. 5.2.5 DOS Utility menu The DOS utility menu shows the Flash BIOS utility DOS version.
ASUS P4B533 motherboard user guide 5-7 5.2.7 Other information The icons on the left side of the screen give additional information on the motherboard and the contents of the support CD. This section shows the pop-up windows that appear when you click the icons.
5-8 Chapter 5: Software support T echnical Support Form The window displays the ASUS T echnical Support Request Form that you have to fill up when requesting technical support. Readme The window displays the contents of the support CD and a brief description of each in text format.
ASUS P4B533 motherboard user guide 5-9 5.3 Softwar e information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information.
5-10 Chapter 5: Software support 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file.
ASUS P4B533 motherboard user guide 5-11 4. From the selection that appears, choose a logo image. Click Next. 6. The next screen prompts you to flash the original BIOS to update it with the new boot logo. Click Flash to update the BIOS. 7. When finished, click Exit, then reboot your computer .
5-12 Chapter 5: Software support 5.3.3 ASUS PC Probe The ASUS PC Probe is a convenient utility to continuously monitor your computer system ’ s vital components, such as fan rotations, voltages, and temperatures.
ASUS P4B533 motherboard user guide 5-13 Using ASUS PC Probe Monitoring Monitor Summary Shows a summary of the items being monitored. T emperature Monitor Shows the PC temperature (for supported processors only).
5-14 Chapter 5: Software support Settings Lets you set threshold levels and polling intervals or refresh times of the PC ’ s temperature, fan rotation, and voltages. History Lets you record the monitoring activity of a certain component of your PC for future reference.
ASUS P4B533 motherboard user guide 5-15 Device Summary Shows a summary of devices present in your PC. DMI Explorer Shows information pertinent to the PC, such as CPU type, CPU speed, and internal/external frequencies, and memory size. Utility Lets you run programs outside of the ASUS Probe modules.
5-16 Chapter 5: Software support ASUS PC Probe T ask Bar Icon Right clicking the PC Probe icon brings up a menu to open or exit ASUS PC Probe and pause or resume all system monitoring. When the ASUS PC Probe senses a problem with your PC, portions of the ASUS PC Probe icon changes to red, the PC speaker beeps, and the ASUS PC Probe monitor appears.
ASUS P4B533 motherboard user guide 5-17 5.3.4 E-Color 3Deep The 3Deep color tuner is designed to match your CR T or LCD color monitor and maximize the color quality of all graphical applications. Y ou may also tune your internet applications to match “true” internet source colors with the color displayed on the monitor .
5-18 Chapter 5: Software support 4. Select the color squares that most closely blend and match with the background. 2. Follow the instructions to manually adjust the brightness level of the monitor . 3. Select the faintest of the three colors: blue , red , and green .
ASUS P4B533 motherboard user guide 5-19 6. When a message appears indicating that the tuning process is complete, click Finish . 5. The next step repeats the color matching process to achieve full color quality . 7. Click on the Set Up Now button to connect to the Internet.
5-20 Chapter 5: Software support 5.3.5 Winbond V oice Editor The Winbond V oice Editor software allows you to customize the vocal POST messages. Install the software from the software menu in the support CD. See section “ 5.2.3 Software menu ” . Follow these steps to use the Winbond V oice Editor .
ASUS P4B533 motherboard user guide 5-21 Changing the default language 1. Click on the Load button. a window showing the available languages appears. 2. Select your desired language then click Open. The event messages for the language you selected appear on the V oice Editor screen.
5-22 Chapter 5: Software support Y ou may want to create a separate folder for your wave files so you can locate them easily in one place. Customizing your POST messages If your language is not in the selection or if you wish to record your own POST messages to replace the pre-installed wave files, you may easily do so.
ASUS P4B533 motherboard user guide 5-23 If you receive an error message telling you that the files exceed the total allowable size, do one or all of the following. • T ry to modify your messages to make them shorter • Save the wave files at a lower quality • Skip lesser used events like FDD Detection, IDE HDD Detection, etc.
5-24 Chapter 5: Software support 5.3.6 Multi-Channel Audio Feature The C-Media PCI Audio Driver and Applications are included in the Support CD that came with your motherboard package.
ASUS P4B533 motherboard user guide 5-25 Running the C-Media Audio Demo Program The C-Media audio demo program allows you to test and fine tune your speaker system. T o launch the the multi-channel audio demo program, click on Start from your desktop, then select PCI Audio Applications/ Multi-Channel Audio Demo .
5-26 Chapter 5: Software support.
Index This part contains an alphabetical list of the topics found in this document..
ASUS P4B533 motherboard.
ASUS P4B533 motherboard user guide I-1 A Accelerated Graphics Port 2-15 Acrobat Reader 5-4 ASUS ASIC 1-9 ASUS EZ Flash 4-1 ASUS EZ Plug™ 1-3, 1-8, 2-27 ASUS iPanel 2-32 ASUS MyLogo2 1-3, 5-10 ASUS P.
I-2 Index DIP switches 1-8, 1-9, 2-16 Double Data Rate (DDR) memory 1- 2 E Expansion card installation 2-13 configuration 2-13 Expansion slots 1-9, 2-13 AGP 1-9, 2-15 PCI 1-9, 2-15 F Flash EEPROM 1-9 .
ASUS P4B533 motherboard user guide I-3 PCI/VGA Palette Snoop 4-26 PIO Mode 4-15 Plug & Play O/S 4-35 Power Management 4-28 Power On Self T est 4-35 PS/2 Keyboard Port 1-10 PS/2 Mouse Port 1-10 PS/.
I-4 Index.
デバイスAsus P4B533の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Asus P4B533をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsus P4B533の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Asus P4B533の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Asus P4B533で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Asus P4B533を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsus P4B533の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Asus P4B533に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsus P4B533デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。