Accton TechnologyメーカーFAST ETHERHUB-12Sの使用説明書/サービス説明書
ページ先へ移動 of 52
Fast EtherHub-12s &INO<GG<ODJI*<IP<G.
Installation Manual Fast EtherHub-12s Smart Fast Ethernet Hub with 12 100BASE-TX Ports.
Copyright (c) 1997 by Accton Technology Corporation. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation.
Package Contents i Package Contents Carefully unpack the contents of the package and verify them against the checklist given below. Package Checklist æ Fast EtherHub-12s (Model No.
Quick Installation iii Quick Installation The Fast EtherHub-12s is a Class II repeater. It contains 12 100BASE-TX Fast Ethernet ports. The smart design built into the front display panel provides a friendly interface that simplifies installation and network troubleshooting.
Fast EtherHub-12s User’s Guide iv Quick Installation first calculate the maximum length permitted between each pair of end nodes as described in Chapter 2 under the section on Precise Cable Length Budgeting .
About this Guide v About this Guide This guide is designed for the experienced network installer. It describes how to install and operate Accton’s Fast EtherHub-12s. After reading this manual, you should be able to use the front display panel and configure options to manage all your network connections.
Contents Contents vii Chapter 1: Product Overview ................................................. 1-1 Introduction to Fast Ethernet ..................................................................................... 1-1 Accton’s Fast EtherHub-12s.
Fast EtherHub-12s User’s Guide viii Contents Appendix A: Troubleshooting ................................................ A-1 Diagnosing Hub Indicators ........................................................................................ A-1 System Diagnostics .
Fast EtherHub-12s User’s Guide Contents ix Limited Warranty ....................................................................................................... E-4 Customer Remedies ...............................................................
Product Overview 1-1 Chapter 1: Product Overview Introduction to Fast Ethernet Standard 10 Mbps Ethernet has served well for past generations of 286 and 386 machines performing simple file transfers.
Fast EtherHub-12s User’s Guide 1-2 Product Overview Basic Features • Transmits data at 100 Mbps for demanding applications • Conforms to the IEEE 802.
Fast EtherHub-12s User’s Guide Product Overview 1-3 • With automatic partitioning and reconnection, any port is automatically isolated if excessive collisions occur on it.
Installing the System 2-1 Chapter 2: Installing the System This chapter provides information on installing the Fast EtherHub-12s, estab- lishing network connections, and configuring the system. You may install this hub on any lev el surface (e.g ., a table or shelf) or in a standard EIA equipment rack.
Fast EtherHub-12s User’s Guide 2-2 Installing the System Connecting the Hub System This hub is a Fast Ethernet repeater for 100BASE-TX networks. The EtherHub-12s has 12 RJ-45 station ports, of which Port 12 can serve as eith er a station port or a daisy- chain port (depending on the port’s switch setting).
Fast EtherHub-12s User’s Guide Installing the System 2-3 Making a Connection via the MDI Daisy-Chain Port 1. To make a direct connection to another compatible rep eater or switch, use the 12MDI daisy-chain port. When connecting to this port, remember to set the port selection switch MDI .
Fast EtherHub-12s User’s Guide 2-4 Installing the System Simplified Cable Length Constraints The Fast EtherHub-12s is a Class II repeater. IEEE recommends that Class II hubs be limited to a cascade of two hubs.
Fast EtherHub-12s User’s Guide Installing the System 2-5 connected hub when using twisted-pair cabling. However, when linking o ne or more F ast Ethernet repeaters tog ether (i.e., in the sam e collision domain), the overall length of cable used between any two nodes should not exceed the limits outlined in the I EEE 802.
Fast EtherHub-12s User’s Guide 2-6 Installing the System Verifying Port Status Check each connection by viewing the port status indicators listed below. (For a more detailed description of these indicators, refer to Chapter 4.) Link Indicates that the port has established a valid network connection.
Fast EtherHub-12s User’s Guide Installing the System 2-7 • Test the adapter for an attached workstation by trying it in another computer that has been successfully connected to the network. If y ou still can’t resolv e the problem , please refer to Troubleshooting in Appendix A.
Configuring the Network 3-1 Chapter 3: Configuring the Network The Fast EtherHub-12s allows great flexibility in configuring your network. You can use it in a stand-alone or multiple hub configuration. Some of the common applications for this Fast EtherHub are described in this chapter.
Fast EtherHub-12s User’s Guide 3-2 Configuring the Network Using the RJ-45 Daisy-Chain Port You can easily connect to another hub via the MDI daisy-chain port (Port 12). When using Simplied Cable Length Constraints as described in Chapter 2, the inter- hub cable length is 5 meters.
Fast EtherHub-12s User’s Guide Configuring the Network 3-3 Precise Guidelines for Configuring Multiple Hubs A detailed formula for calculating maximum cable length was provided in the section on Precise Cable Length Budgeting in Chapter 2.
Fast EtherHub-12s User’s Guide 3-4 Configuring the Network Figure 3- 3 Cabling Limits for Multiple Hub Configuration Notes: 1. The maximum length for each cable must be determined by calculations for the longest path (i.e., node-to-node connection) that passes through that segment.
Hardware Reference 4-1 Chapter 4: Hardware Reference Before connecting any network device to this hub, please review Chapter 2 for information on system installation and Chapter 3 for a brief look at common network architectures. This chapter describes the hardware features of the Fast EtherHub-12s.
Fast EtherHub-12s User’s Guide 4-2 Hardware Reference The front panel array provides indicators that show the utilization of network bandwidth and indicate the statu s o f p o rt c o n n e ct io n s . I t in c lu d e s port status indicators and a statistical display for network traffic as shown below.
Fast EtherHub-12s User’s Guide Hardware Reference 4-3 Statistical Display for System Performance Utilization - ( Utilization % ) The statistical indicators show the percentage of valid data passing through all ports compared to overall network bandwidth (updated every 0.
Fast EtherHub-12s User’s Guide 4-4 Hardware Reference Note: If the hub displays a high collision rate, check to see if any of the connected devices are malfunctioning or if a loop has been formed in your network connections. Otherwise, you may need to reconfigure your network to balance the traffic load.
Fast EtherHub-12s User’s Guide Hardware Reference 4-5 Troubleshooting : If the Link LED does not light up w hen a device is connected to its corre- sponding port, check that both the hub and connected dev ice ar e pow ered on.
Fast EtherHub-12s User’s Guide 4-6 Hardware Reference Rear Panel The rear panel on the hub includes a full- rang e p ow er so ck et. Figure 4.3 Rear Panel Power Socket The power socket accepts AC power from 100 to 240V at 50 to 60Hz. The unit is equipped with a universal full-range power source.
Troubleshooting A-1 Appendix A: Troubleshooting Diagnosing Hub Indicators This Fast EtherHub can be easily monitored through its com prehensive panel indicators. These indicators assist the network manager in identifying problems the hub may encounter.
Fast EtherHub-12s User’s Guide A-2 Troubleshooting System Diagnostics Power and Cooling Problems If the Power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section.
Fast EtherHub-12s User’s Guide Troubleshooting A-3 External Adapters Make sure the network interface hardware and software drivers for the attached devices are function properly. Check the adapter cards and associated drivers used in any attached workstation or server.
Cable and Port Assignments B-1 Appendix B: Port and Cable A ssignments RJ-45 Port Figure B-1 RJ-45 Connector (on the Hub Side) Pin MDI-X Assignment (Station Port 1 ~ 12) MDI Assignment (Cascade Port 1.
Product Specifications C-1 Appendix C: Product Specifications Transmission Technique Baseband Topology Star or Tree Access Method CSMA/CD, 100Mbps Standards Conformance IEEE 802.
Regulatory Standards Compliance D-1 Appendix D: Regulatory Standards Compliance EMI Certification FCC Class B Certification Accton Technology Corporation Model Numbers: EH3012-TX FCC ID: HED3012EHLCT-TX This device complies with Part 15 of the FCC Rules.
Fast EtherHub-12s User’s Guide D-2 Regulatory Standards Compliance Warnings 1. Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge whenever handling this equipment.
Fast EtherHub-12s User’s Guide Regulatory Standards Compliance D-3 Read the instructions for correct handling. European Community Immunity Requirements This unit was tested and found to comply with the Class B limits of EN55022 (CISPR 22) and the immunity requirements of EN50082-1.
Fast EtherHub-12s User’s Guide D-4 Regulatory Standards Compliance Safety Compliance Underwriters Laboratories Inc. Important! Before making connections, make sure you have the correct Cord Set. Check it (read the label on the cable) against the following specification list.
Fast EtherHub-12s User’s Guide Regulatory Standards Compliance D-5 Sicherheitshinweise 1. Die Steckdose muß sich in der Nähe des Gerätes befinden und leicht zugänglich sein. 2. Zum Reinigen den Stecker aus der Steckdose ziehen. Beim Reinigen keine Flüssigreiniger oder Sprays verwenden, sondern ein angefeuchtetes Tuch.
Product Support Services E-1 Appendix E: Product Support Services Product Registration Fill in the Owner Registration Card and mail it to Accton Technology Corporation.
Fast EtherHub-12s User’s Guide E-2 Product Support Services After repair, Accton will inform you of the date of delivery and the exact amount due. Please send the payment by T/T (Telegram Transfer), and Accton will send you the fixed component after receiving payment.
Fast EtherHub-12s User’s Guide Product Support Services E-3 Technical Support Your dealer or installer is the person who understands your network and Accton units. If neither is available to help you, Accton technical support engineers are available by FAX, mail or phone.
Fast EtherHub-12s User’s Guide E-4 Product Support Services Limited Warranty Accton warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for the lifetime of the product.
Fast EtherHub-12s User’s Guide Product Support Services E-5 Return Process Before you may return any Accton product to Accton, you must request an RMA number by calling, FAXing or writing Accton’s Service Department at the address listed below. If you ship the product, you must assume the risk of damage or loss in transit.
Fast EtherHub-12s User’s Guide E-6 Product Support Services Accton Offices Accton Technology Corporation International Headquarters, No. 1 Creation Rd.
Glossary 1 Glossary 100BASE-TX IEEE’s specifications for 100 Mbps Ethernet using twisted-pair cable (100 W Cat. 5 STP or UTP ) . The maximum length of cable for a point-to-point connection is 100 meters. Collision A condition in which two packets transmitted over a medium interfere with each other.
Fast EtherHub-12s User’s Guide 2 Glossary Fast Ethernet 100 Mbps network communication system based on Ethernet and the CSMA/CD access method. IEEE 802.3 Standard Standard for the physical and electrical connections in local area networks developed by the IEEE.
Fast EtherHub-12s User’s Guide Glossary 3 Shielded Twisted-Pair (STP) 100 W Category 5 twisted-pair wire covered with an external aluminum-foil or woven- copper shield designed to reduce excessive noise pick up or radiation. The STP cable refered to in this manual is also sometimes called screened twisted-pair (ScTP).
Index 1 Index A Accton's Fast EtherHub-12s • 1-1 Automatic Partitioning • 1-3 Automatic Polarity Detection • 1-3 C Cable Length Precise Cable Length Budgeting • 2-4 Simplified Cable Lengt.
Fast EtherHub-12s User’s Guide 2 Index M Maximum Cable Length • 2-4 MDI Daisy-chain Port • 3-2 N Network Connection MDI Daisy-Chain Port • 2-3 MDI-X Station Port • 2-2 P Port and Cable Assig.
EH3012-TX 150114-101 E0197-R02.
デバイスAccton Technology FAST ETHERHUB-12Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Accton Technology FAST ETHERHUB-12Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAccton Technology FAST ETHERHUB-12Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Accton Technology FAST ETHERHUB-12Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Accton Technology FAST ETHERHUB-12Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Accton Technology FAST ETHERHUB-12Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAccton Technology FAST ETHERHUB-12Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Accton Technology FAST ETHERHUB-12Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAccton Technology FAST ETHERHUB-12Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
