PanasonicメーカーDMC-XS1GAの使用説明書/サービス説明書
ページ先へ移動 of 39
© Panasonic Corporation 2013 Unauthorized copy- ing and distribution is a violation of law . ORDER NO. DSC1302004CE B26 Digit al Camera Model No. DMC-XS1P DMC-XS1PC DMC-XS1PU DMC-XS1EB DMC-XS1EE DMC-XS1EF DMC-XS1EG DMC-XS1EP DMC-XS1GA DMC-XS1GC DMC-XS1GF DMC-XS1GK DMC-XS1GN DMC-XS1G T Colour (W).
2 T ABLE OF CONTENTS PA G E PA G E 1 Safety Precautions --------------------------- -------------------- 3 1.1. General Guidelines ------------------------------------- --- 3 1.2. Leakage Current Cold Check --------------------------- 3 1.3. Leakage Current Hot Ch eck (See Figure.
3 1 Safety Precautions 1.1. General Guidelines 1. IMPORT ANT SAFETY NOTICE There are special compo nents used in this equipment which are important for safety . These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List.
4 1.4. How to Discharge the E.Ca p acitor on Flash T op P .C.B. CAUTION: • Be sure to discharge the E.Capacitor on Flash T op P . C.B. before disassembling. • Be careful of the high volt age circuit on Flash T op P .C.B. when servicin g. [Discharging Proce dure] 1.
5 2W a r n i n g 2.1. Prevention of Electrost atic Di scharge (ESD) to Electrost atically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easi ly by static electricity . Such components commonly are called Elec- trostatically Sensitive (ES) Devices.
6 3 Service Navigation 3.1. Introduction This service manual contains technical information, which a llow se rvice personnel’s to understand and se rvice this model.
7 3.3. General Description Abou t Lead Free Solder (PbF) The lead free sold er has been used in the mounting process of all electrical components on the printed circuit board s used for this equipment in considering th e globally environmen tal conservation.
8 3.4. How to Define the Model Suffix (NTSC or P A L model) There are seven kinds of DMC- XS1, regardless of the colours. • a) DMC-XS1 (Japan domestic model) • b) DMC-XS1P/PC • c) DMC-XS1EB/EF/E.
9 3.4.2. INITIAL SETTINGS: After replacing the Main P .C.B., make sure to perform the in itial settings after achieving the adj ustment by ordering the follo wing procedure in accordance with model suffix of the unit. 1. IMPORT ANT NOTICE: Before proceeding Initial settings, make sure to read the following CAUTIONS.
10 • Step 4. Display the INITIAL SETTING: While pressing [ MENU/SET ] button and “[ RIGHT ] of Cursor button” simu ltaneously , turn the Power off. The “INITIAL SETTINGS” menu is displayed . There are two kinds of “INITIAL SETTINGS” menu form as follows: [CASE 1.
11 • Step 6. Set the model suffi x in “INITIAL SETTINGS”: Press the “[ RIGHT ] of Cursor buttons”. The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation. (The unit is powered off automatica lly .
12 4 S pecifications The following specification is for DMC-XS1P/DMC-FH10P . Some specifications may differ depending on model suffix..
13 5 Location of Controls and Component s The following descri ption is for DMC-XS1P . Some descriptions ma y differ depending on model suffix..
14.
15 6 Service Mode 6.1. Error Code Memory Function 1. General description This unit is equipped with h istory of error code memory func tion, and can be memorized 16 error cod es in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
16 Error Code List The error code co nsists of 8 bits data and it shows the following information..
17 Important notice about “Error Code L ist” 1) About “*” indication: The third digit from the left is dif ferent as follows. - In case of 0 (example: 18 0 01000) When the third digit from the left shows “0”, thi s erro r occurred under the condition of INIT IAL SETTINGS has been completed.
18 7 Service Fixture & T ools 7.1. Service Fixture and T ools The following Service Fixture and tools are us ed for checking and servicing this uni t. 7.2. When Replacing the Main P .C.B. After replacing the Main P .C.B., be sure to achieve adjustment.
19 7.3. Service Position Check the Flash T op P .C.B., when servic ing this DSC.(Refer to the following.) CAUTION. (When servicing Flash T op P .C.B.) 1. Be sure to discharge th e E.Capacitor on Flas h T op P .C.B.. Refer to “How to Discharge the E.
20 8 Disassembly and Assembly Instructions 8.1. Disassembly Flow Chart This is a disassembling chart. When assembling, perform this chart conve rsely .
21 8.3. Disassembly Procedure 8.3.1. Removal of the Rear Case Unit (Fig. D1) No. Item Fig Removal 1 Rear Case Unit (Fig. D1) Memory Card Batter y 2 Screws (A) 3 Screws (B) (Fig. D2) Rear Case U nit 2 Rear Op Plate Unit (Fig. D3) 1 Scr ew (C) 1 Locking tab 2 Hooking parts Connector (A) Rear Op Plate Unit 3 Front Case Unit (Fig.
22 (Fig. D2) 8.3.2. Removal of the Rear Op Plate Unit (Fig. D3).
23 8.3.3. Removal of th e Front Case Unit (Fig. D4) 8.3.4. Removal of the LCD Unit (Fig. D5).
24 8.3.5. Removal of the Frame Plate (Fig. D6) 8.3.6. Removal of the T op Case Unit (Fig. D7) (Fig. D8).
25 8.3.7. Removal of the Flash T op P .C.B. (Fig. D9) 8.3.8. Removal of th e Lens Unit (W/C CD) (Fig. D10) 8.3.9. Removal of the Main P .C.B. and Speaker (Fig.
26 (Fig. D12) [ When Inst alling ] CA TION: Before soldering the T erminal A (Connecting p art of Main P .C.B. and Frame Unit). Before soldering the T erminal A, make sure to tighten the “Screw (F)” first in o rder to eliminate the gap between Main P .
27 8.3.10. Removal of th e Battery Door Unit (Fig. D13) NOTE: (When Installing) Make sure to confirm the following points when installing: • The Screw is tigh tened enoug h. • Installing conditions are fine. (No distortion , no abnormal- space.) • No dust and/or dirt on Le ns surfaces.
28 8.4. Removal of the CCD FPC Un it When remove the CCD FPC Unit once (the screw (G) is loos- ened even a little), the optical tilt adjustment is required. When loosen the screw (G), neces sa ry the optical tilt ad just- ment at the end of assembling.
29 9 Measurement s and Adjustments 9.1. Introduction When servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced. Before disassembling the unit, it is recomme nded to back up the camera data stored in Flash -ROM as a data file.
30 9.2.2. Flash-ROM Data Backup Number of necessary adjustment items decreas es by copying the backup d ata to new Main P . C.B. when adjustment data in old Main P .
31 9.3. Det ails of Electrical Adjustment 9.3.1. How to execute the Electrical Adjustment It is not necessary to connect the camera to a PC to perfor m adjustments. “Flag reset operation” and “Initial setting operation” are requ ired when carrying out the alignm ent, fo llow the procedure below .
32 9.3.1.3. Execute Adjustment (In case of “OIS Adjustment”) 1. Perform step “9.3.1.1.” to “9 .3.1.2.”, to re set the OIS flag status “F” (Set) to “0” (Reset) 2. Press “[ W ] side of the Zoom button” after Flag reset. OIS Adjustment screen is displayed on the LCD panel.
33 9.3.2. Adjustment Specifications The following matrix table shows the relation between the rep laced part and the N ecessary Adjustment. When a part is replaced, make sure to perform t he necessary a djustment(s) in the order indi cated. The table below shows all the information nece ssary to perform each adjustment.
34.
35 9.4. Af ter Adjustment 9.4.1. Initial Setting Since the initial setting h as been released to execute the built-i n adjustment so ftware, it should be set up ag ain before shipp ing th e camera to the customer . Refer to the procedure described in “3.
36 10 Maintenance 10.1. Cleaning Lens and LCD Panel Do not touch the surface of l ens and L CD Panel wi th your h and. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel , dampen the lens cleanin g pape r with lens clean er , and the gently wipe the its surface.
37 1 1 Block Diagram 1 1.1. Overall Block Diagram CCD SIGNAL PROCESSOR FOCUS IRIS SDRAM/1G-bit NAND FLASH ROM/1G-bit MEMORY CARD REAR OPERA TION UNIT OVERALL BLOCK DIAGRAM OIS UNIT VENUS ENGINE CAMERA.
38 1 1.2. Flash / T op Block Diagram 1 1.3. Sub Operation Block Diagram DMC-XS1 FLASH TOP BLOCK DIAGRAM FLASH TOP BLOCK DIAGRAM F8001 3 5 2 1 T8001 CL8004 C8003 (For Flash Charge) FLASH UNIT FLASH TOP P .
39 12 Wiring Connection Diagram 12.1. Interconnection Diagram DMC-XS1 INTERCONNECTION DIAGRAM INTERCONNECTION DIAGRAM MAIN P.C.B. (COMPONENT SIDE) : (FOIL SIDE) FLASH TOP P.
デバイスPanasonic DMC-XS1GAの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic DMC-XS1GAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic DMC-XS1GAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic DMC-XS1GAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic DMC-XS1GAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic DMC-XS1GAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic DMC-XS1GAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic DMC-XS1GAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic DMC-XS1GAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
