AsusメーカーP6T Deluxe V2の使用説明書/サービス説明書
ページ先へ移動 of 182
Motherboard P6T Deluxe V2.
ii E4398 First Edition December 2008 Copyright © 2008 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, trans.
iii Contents Contents ...................................................................................................... iii Notices ....................................................................................................... viii Safety information .
iv Contents 2.5.6 PCI Express 2.0 x16 slots ............................................. 2-22 2.6 Jumpers ...................................................................................... 2-24 2.7 Onboard switches ...............................
v Contents 3.3.7 AHCI Conguration ....................................................... 3-15 3.3.8 System Information ....................................................... 3-16 3.4 Ai T weaker menu ..............................................
vi Contents 3.6.4 ACPI APIC Support ...................................................... 3-32 3.6.5 APM Conguration ........................................................ 3-33 3.6.6 Hardware Monitor .............................................
vii Contents 4.4.1 RAID denitions ............................................................ 4-44 4.4.2 Installing Serial A T A hard disks ..................................... 4-45 4.4.3 Intel ® RAID congurations ............................
viii Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
ix Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
x About this guide This user guide contains the information you need when installing and conguring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports.
xi Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. T ypography Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase.
xii P6T Deluxe V2 specications summary (continued on the next page) CPU LGA1366 socket for Intel ® Core™ i7 Processor Extreme Edition / Core™ i7 Processor Supports Intel ® Dynamic Speed T echnology * Refer to www .asus.com for Intel CPU support list Chipset Intel ® X58 / ICH10R System Bus Up to 6.
xiii (continued on the next page) P6T Deluxe V2 specications summary ASUS Unique features ASUS Exclusive Features: - ASUS T urboV - ASUS T rue 16+2 Phase Power Design - Express Gate SSD ASUS Power .
xiv P6T Deluxe V2 specications summary *Specications are subject to change without notice. Back Panel I/O Ports 1 x PS/2 Keyboard / Mouse combo port 1 x S/PDIF Out (Coaxial + Optical) 1 x External SA T A 1 x IEEE1394a 2 x RJ45 ports 8 x USB 2.0/1.
1 Chapter 1: Product introduction This chapter describes the motherboard features and the new technologies it supports..
ASUS P6T Deluxe V2 Chapter summary 1 1.1 Welcome! ...................................................................................... 1-1 1.2 Package contents ......................................................................... 1-1 1.3 Special features .
ASUS P6T Deluxe V2 1-1 1.1 Welcome! Thank you for buying an ASUS ® P6T Deluxe V2 motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in th.
1-2 Chapter 1: Product Introduction 1.3 Special features 1.3.1 Product highlights Green ASUS This motherboard and its packaging comply with the European Union’s Restriction on the use of Hazardous Substances (RoHS).
ASUS P6T Deluxe V2 1-3 1.3.2 ASUS Unique features ASUS T urboV Feel the adrenaline rush of real-time OC—now a reality with the ASUS T urboV . This extreme OC tool lets you set new ambitions on the OC stage with an advanced and easy-to-use interface—allowing you to overclock without exiting or rebooting the OS.
1-4 Chapter 1: Product Introduction ASUS EPU-6 Engine The new ASUS EPU—the world’s rst power saving engine, has been upgraded to a new 6 engine version, which provides total system power savings by detecting current PC loadings and intelligently moderating power in real-time.
ASUS P6T Deluxe V2 1-5 Fan Xpert ASUS Fan Xpert intelligently allows users to adjust both the CPU and chassis fan speed according to different ambient temperature, which is caused by different climate conditions in dif ferent geographic regions and system loading.
1-6 Chapter 1: Product Introduction ASUS Onboard Switch With an easy press during overclock, this exclusive onboard switch allows gamer to effortless ne-tune the performance without having to short the pins! See page 2-26 for details.
ASUS P6T Deluxe V2 1-7 ASUS MyLogo2™ This feature allows you to convert your favorite photo into a 256-color boot logo for a more colorful and vivid image on your screen. See page 4-9 for details. ASUS Multi-language BIOS The multi-language BIOS allows you to select the language of your choice from the available options.
1-8 Chapter 1: Product Introduction.
2 Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
ASUS P6T Deluxe V2 Chapter summary 2 2.1 Before you proceed ..................................................................... 2-1 2.2 Motherboard overview ................................................................. 2-2 2.3 Central Processing Unit (CPU) .
2.1 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component.
2.2 Motherboard overview 2.2.1 Motherboard layout Refer to 2.8 Connectors for more information about rear panel connectors and internal connectors. 2-2 Chapter 2: Hardware information.
2.2.2 Layout contents Connectors/Jumpers/Slots Page 1. A TX power connectors (24-pin EA TXPWR, 8-pin EA TX12V) 2-36 2. LGA1366 CPU Socket 2-6 3. CPU, chassis, and power fan connectors (4-pin CPU_F AN, 3-pin CHA_F AN1-3, 3-pin PWR_F AN) 2-34 4. DDR3 DIMM slots 2-12 5.
DO NOT overtighten the screws! Doing so can damage the motherboard. 2.2.3 Placement direction When installing the motherboard, m ake sure that you place it into the ch assis in the correct orientation. The edge with external ports goes to the rear p art of the chassis as indicated in the image below .
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA1366 socket designed for the Intel ® Core™ i7 Processor Extreme Edition / Core™ i7 Processor . • Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent.
2.3.1 Installing the CPU T o install a CPU: 1. Locate the CPU socket on the motherboard. T o prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab.
The CPU ts in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 6. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket, and then t the socket alignment key into the CPU notch.
8. Close the load plate (A), and then push the load lever (B) until it snaps into the retention tab. A B 2-8 Chapter 2: Hardware information.
2.3.2 Installing the CPU heatsink and fan The Intel ® LGA1366 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel ® processor , the package includes the CPU fan and heatsink assembly .
3. Connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN. DO NOT forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector . 2.3.3 Uninstalling the CPU heatsink and fan T o uninstall the CPU heatsink and fan: 1.
2.3.4 Installing the optional fans Install the optional fan only if you are using a passive cooler or a water cooler . Installing the optional fan with an active CPU cooler will interfere with the airow and destabilize the system. 1. Position the fan above the pipe and heatsink assembly .
2.4 System memory 2.4.1 Overview The motherboard comes with six Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) sockets. A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched differently to prevent installation on a DDR2 DIMM socket.
2.4.2 Memory congurations Y ou may install 1GB and 2GB unbuffered and non-ECC DDR3 DIMMs into the DIMM sockets. • The default memory operation frequency is dependent on its SPD. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value.
V endor Part No. Size SS/ DS Chip Brand Chip NO. Timing DIMM (BIOS) V oltag e DIMM socket support (Optional) A* B* KINGSTON KHX14900D3K3/3GX (XMP) 3GB (Kit of 3) SS N/A Heat-Sink Package (1333-9-9-9-24) 1.
V endor Part No. Size SS/ DS Chip Brand Chip NO. Timing DIMM (BIOS) Voltage DIMM socket support (Optional) A* B* D* CORSAIR TR3X6G1600C8D (XMP) 6GB (kit of 3) DS N/A Heat-Sink Package 8-8-8-24 (1601-8-8-8-24) 1.65 • • • CORSAIR TR3X6G1600C9 (XMP) 6GB (kit of 3) DS N/A Heat-Sink Package 9-9-9-24 (1333-9-9-9-24) 1.
P6T Deluxe V2 Motherboard Qualied V endors Lists (QVL) DDR3-1333MHz capability • Hyper DIMM (DDR3 1800MHz or above) support is subject to the physical characteristics of individual CPUs. • Please load X.M.P or D.O.C.P setting in BIOS for hyper DIMM (DDR3 1800MHz or above) support.
V endor Part No. Size SS/ DS Chip Brand Chip NO. Timing DIMM (BIOS) V oltage DIMM socket support (Optional) A* B* C* D* G.SKILL F3-10666CL9D-4GBPK 4GB (kit of 2) DS N/A Heat-Sink Package (1333-9-9-9-24) 1.65 • • • • G.SKILL F3-10666CL9T -6GBNQ 6GB (kit of 3) DS N/A Heat-Sink Package 9-9-9-24 (1333-9-9-9-24) 1.
P6T Deluxe V2 Motherboard Qualied V endors Lists (QVL) DDR3-1067MHz capability Side(s): SS - Single-sided DS - Double-sided DIMM support: • A* : Supports two (2) modules inserted into slot A1 and B1 as one pair of Dual-channel memory conguration.
2.4.4 Removing a DIMM Follow these steps to remove a DIMM. 1. Simultaneously press the retaining clips outward to unlock the DIMM. 2. Remove the DIMM from the socket. Support the DIMM lightly with your ngers when pressing the retaining clips. The DIMM might get damaged when it ips out with extra force.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.
2.5.3 Interrupt assignments Standard interrupt assignments * These IRQs are usually available for PCI devices. IRQ Priority Standard function 0 1 System T imer 1 2 Keyboard Controller 2 – Redirect t.
2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specications. Refer to the gure below for the location of the slot.
• In single VGA card mode, use rst the PCIe 2.0 x16_1 slot (blue) for a PCI Express x16 graphics card to get better performance. • In CrossFireX™ or SLI™ mode, use the PCIe 2.0 x16_1 (blue) and PCIe 2.0 x16_2 (white) slots for PCI Express x16 graphics cards to get better performance.
2.6 Jumpers 1. Clear RTC RAM (CLRTC) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
2. CPU / DRAM Bus / QPI DRAM overvoltage setting (3-pin OV_CPU, 3-pin OV_DRAM_BUS, 3-pin OV_QPI_DRAM) These jumpers allow you to enable or disable the advanced CPU, DRAM Bus, and QPI DRAM overvoltage settings in BIOS. Read the following information before you change the jumper settings.
2.7 Onboard switches Onboard switches allow you to ne-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. 1. Power-on switch Press the power-on switch to wake/power up the system.
2.8 Connectors 2.8.1 Rear panel connectors 1. PS/2 keyboard / mouse combo port. This port is for a PS/2 keyboard or a PS/2 mouse. 2. Coaxial S/PDIF Out port. This port connects an external audio output device via a coaxial S/PDIF cable. 3. LAN 2 (RJ-45) port.
12. USB 2.0 ports 1 and 2. These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 13. External SA T A port. This port connects to an external a Serial A T A hard disk drive. DO NOT insert a dif ferent connector to the external SA T A port.
2.8.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided oppy disk drive (FDD) signal cable. Insert one end of the cable to this connector , then connect the other end to the signal connector at the back of the oppy disk drive.
Drive jumper setting Mode of device(s) Cable connector Single device Cable-Select or Master - Black T wo devices Cable-Select Master Black Slave Gray Master Master Black or gray Slave Slave • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector .
4. ICH10R Serial A T A connectors (7-pin SA T A 1-6 [red]) These connectors are for the Serial A T A signal cables for Serial A T A hard disk drives and optical disc drives.
5. USB connectors (10-1 pin USB910, USB1 1 12, USB1314) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.
6. IEEE 1394a port connector (10-1 pin IE1394_2) This connector is for an IEEE 1394a port. Connect the IEEE 1394a module cable to this connector , then install the module to a slot opening at the back of the system chassis. Never connect a USB cable to the IEEE 1394a connector .
7. CPU, chassis and power fan connectors (4-pin CPU_F AN, 3-pin CHA_F AN1-3, 3-pin PWR_F AN) The fan c onnect ors su pport cooli ng fan s of 3 50 mA ~ 2000 mA (24 W max.
8. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector . The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced.
10. A TX power connectors (24-pin EA TXPWR, 8-pin EA TX12V) These connectors are for A TX power supply plugs. The power supply plugs are designed to t these connectors in only one orientation. Find the proper orientation and push down rmly until the connectors completely t.
1 1. Optical drive audio co nne cto r (4-pin CD) This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner , or MPEG card. 12. Digital audio con nec tor (4-1 pin SPDIF) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s).
• System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector . The system power LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
ASUS Q-Connector (system panel) Y ou can use the ASUS Q-Connector to connect/disconnect chassis front panel cables in a few steps. Refer to the instructions below to install the ASUS Q-Connector . 2. Install the ASUS Q-Connector to the system panel connector , making sure the orientation matches the labels on the motherboard.
2.9 Installing the additional heatsink fan Y ou can install an additional 40 mm x 40 mm system fan (purchased separately) on the Northbridge heatsink for better cooling performance.
2.10 Starting up for the rst time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector .
2.11 Turning off the computer 2.1 1.1 Using the OS shut down function If you are using Windows ® Vista™: 1. Click the Start button then select Shut Down . 2. The power supply should turn off after Windows ® shuts down. If you are using Windows ® XP: 1.
3 BIOS setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 3 ASUS P6T Deluxe V2 3.1 Managing and updating your BIOS ............................................ 3-1 3.2 BIOS setup program .................................................................... 3-9 3.3 Main menu ...................
ASUS P6T Deluxe V2 3-1 3.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows ® environment.) 2. ASUS EZ Flash 2 (Updates the BIOS using a oppy disk or USB ash disk.
3-2 Chapter 3: BIOS setup Quit all Windows ® applications before you update the BIOS using this utility . 3. Select the ASUS FTP site nearest you to avoid network trafc, or click Auto Select . Click Next . Updating the BIOS through the Internet T o update the BIOS through the Internet: 1.
ASUS P6T Deluxe V2 3-3 Updating the BIOS through a BIOS le T o update the BIOS through a BIOS le: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate . The ASUS Update main window appears.
3-4 Chapter 3: BIOS setup 3.1.2 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go through the long process of booting from a oppy disk and using a DOS-based utility .
ASUS P6T Deluxe V2 3-5 3.1.3 Creating a bootable oppy disk 1. Do either one of the following to create a bootable oppy disk. DOS environment a. Insert a 1.44MB oppy disk into the drive. b. At the DOS prompt, type format A: / S then press <Enter>.
3-6 Chapter 3: BIOS setup 3.1.4 AFUDOS utility The AFUDOS utility allows you to update the BIOS le in DOS environment using a bootable oppy disk with the updated BIOS le. This utility also allows you to copy the current BIOS le that you can use as backup when the BIOS fails or gets corrupted during the updating process.
ASUS P6T Deluxe V2 3-7 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support DVD to the bootable oppy disk you created earlier . 3. Boot the system in DOS mode, then at the prompt type: afudos /i[lename] where [lename] is the latest or the original BIOS le on the bootable oppy disk.
3-8 Chapter 3: BIOS setup 3.1.5 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS le when it fails or gets corrupted during the updating process.
ASUS P6T Deluxe V2 3-9 3.2 BIOS setup program This motherboard supports a programmable rmware chip that you can update using the provided utility described in section 3.1 Managing and updating your BIOS . Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to “Run Setup.
3-10 Chapter 3: BIOS setup 3.2.2 Menu bar The menu bar on top of the screen has the following main items: Main For changing the basic system conguration Ai T weaker For changing the overclocking se.
ASUS P6T Deluxe V2 3-1 1 3.2.4 Menu items The highlighted item on the menu bar displays the specic items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power , Boot, and Exit) on the menu bar have their respective menu items.
3-12 Chapter 3: BIOS setup 3.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. 3.3.1 System Time [xx:xx:xx] Allows you to set the system time. 3.3.2 System Date [Day xx/xx/xxxx] Allows you to set the system date.
ASUS P6T Deluxe V2 3-13 3.3.5 SA T A 1-6 While entering Setup, the BIOS automatically detects the presence of Serial A T A devices. There is a separate sub-menu for each SA T A device. Select a device item then press <Enter> to display the SA T A device information.
3-14 Chapter 3: BIOS setup DMA Mode [Auto] Selects the DMA mode. Conguration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Self-Monitoring, Analysis, and Reporting T echnology .
ASUS P6T Deluxe V2 3-15 Hard Disk Write Protect [Disabled] Disables or enables device write protection. This will be ef fective only if the device is accessed through BIOS. Conguration option: [Disabled] [Enabled] IDE Detect Time Out (Sec) [35] Selects the time out value for detecting A T A/A T API devices.
3-16 Chapter 3: BIOS setup 3.3.8 System Information This menu gives you an overview of the general system specications. The BIOS automatically detects the items in this menu. Bios Information Displays the auto-detected BIOS information. Processor Displays the auto-detected CPU specication.
ASUS P6T Deluxe V2 3-17 3.4 Ai Tweaker menu The Ai T weaker menu items allow you to congure overclocking-related items. T ake caution when changing the settings of the Ai T weaker menu items. Incorrect eld values can cause the system to malfunction.
3-18 Chapter 3: BIOS setup 3.4.2 CPU Ratio Setting [Auto] Allows you to adjust the ratio between CPU Core Clock and BCLK Frequency . Use the <+> and <-> keys to adjust the value. Conguration options: [Auto] [12.0] [13.0] [14.0] [15.0] [16.
ASUS P6T Deluxe V2 3-19 PCIE Frequency [XXX] Allows you to set the PCI Express frequency . Use the <+> and <-> keys to adjust the PCIE frequency . The values range from 100 to 200. 3.4.5 DRAM Frequency [Auto] Allows you to set the DDR3 operating frequency .
3-20 Chapter 3: BIOS setup DRAM WRITE Recovery T ime [Auto] Conguration options: [Auto] [1 DRAM Clock] – [15 DRAM Clock] DRAM READ to PRE T ime [Auto] Conguration options: [Auto] [1 DRAM Clock.
ASUS P6T Deluxe V2 3-21 DRAM READ to READ Delay(DD) [Auto] Conguration options: [Auto] [2 DRAM Clock] – [9 DRAM Clock] DRAM READ to READ Delay(DR) [Auto] Conguration options: [Auto] [2 DRAM Cl.
3-22 Chapter 3: BIOS setup 3.4.10 IOH V oltage [Auto] Allows you to set the I/O Hub (IOH) voltage. The values range from 1.10V to 1.70V with a 0.02V interval. 3.4.1 1 IOH PCIE V oltage [Auto] Allows you to set the IOH PCIE voltage. The values range from 1.
ASUS P6T Deluxe V2 3-23 Blue Y ellow Purple Red CPU V oltage 0.85000V– 1.22500V 1.23125V– 1.29375V 1.30000V– 1.35000V 1.35625V 1.70000V CPU PLL V oltage 1.80V–1.90V 1.92V–2.00V 2.02V–2.10V 2.12V–2.50V QPI/DRAM Core V oltage 1.20000V– 1.
3-24 Chapter 3: BIOS setup 3.4.20 CPU Spread Spectrum [Auto] Set to [Disabled] to enhance BCLK overclocking ability or [Auto] for EMI control. Conguration options: [Auto] [Disabled] 3.4.21 IOH Clock Skew [Auto] Adjusting this item may help enhancing BCLK overclocking ability .
ASUS P6T Deluxe V2 3-25 3.5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. T ake caution when changing the settings of the Advanced menu items. Incorrect eld values can cause the system to malfunction.
3-26 Chapter 3: BIOS setup CPU Ratio Setting [Auto] Allows you to adjust the ratio between CPU Core Clock and BCLK Frequency . Use the <+> and <-> keys to adjust the value. Conguration options: [Auto] [12.0] [13.0] [14.0] [15.0] [16.0] [17.
ASUS P6T Deluxe V2 3-27 A20M [Disabled] Legacy OSes and APs may need A20M enabled. Conguration options: [Disabled] [Enabled] Intel(R) SpeedStep (TM) T ech [Enabled] When set to [Disabled], the CPU runs at its default speed. When set to [Enabled], the CPU speed is controlled by the operating system.
3-28 Chapter 3: BIOS setup 3.5.2 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. NorthBridge Chipset Conguration PCI Express Selector [Auto] Allows you to decide the Link Width of the PCIe x16_2 slot and PCIe x16_3 slot.
ASUS P6T Deluxe V2 3-29 High Denition Audio [Enabled] Allows you to enable or disable the High Denition Audio Controller . Conguration options: [Enabled] [Disabled] Front Panel T ype [HD Audi.
3-30 Chapter 3: BIOS setup 3.5.4 USB Conguration The items in this menu allows you to change the USB-related features. Select an item then press <Enter> to display the conguration options. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit v02.
ASUS P6T Deluxe V2 3-31 3.5.5 PCIPnP The PCIPnP menu items allow you to change the advanced settings for PCI/PnP devices. Plug And Play O/S [No] When set to [NO], BIOS congures all the devices in the system.
3-32 Chapter 3: BIOS setup 3.6 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press <Enter> to display the conguration options.
ASUS P6T Deluxe V2 3-33 3.6.5 APM Conguration Restore On AC Power Loss [Power Off] When set to [Power Off], the system goes into of f state after an AC power loss.
3-34 Chapter 3: BIOS setup 3.6.6 Hardware Monitor CPU T emperature [xxxºC/xxxºF] MB T emperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. Select [Ignored] if you do not wish to display the detected temperatures.
ASUS P6T Deluxe V2 3-35 Chassis Q-Fan Control [Disabled] Allows you to enable or disable the Chassis Q-fan control feature. Conguration options: [Disabled] [Enabled] The following item appears only when you enable the Chassis Q-Fan Control item. Chassis Fan Profile [Standard] Allows you to set the appropriate performance level of the ASUS Q-Fan.
3-36 Chapter 3: BIOS setup 3.7 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu. 3.7.1 Boot Device Priority 1st ~ xxth Boot Device [xxx Drive] These items specify the boot device priority sequence from the available devices.
ASUS P6T Deluxe V2 3-37 3.7.2 Boot Settings Conguration Quick Boot [Enabled] Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items.
3-38 Chapter 3: BIOS setup 3.7.3 Security The Security menu items allow you to change the system security settings. Select an item then press <Enter> to display the conguration options. Change Supervisor Password Select this item to set or change the supervisor password.
ASUS P6T Deluxe V2 3-39 User Access Level [Full Access] This item allows you to select the access restriction to the Setup items. Conguration options: [No Access] [View Only] [Limited] [Full Access] [No Access] prevents user access to the Setup utility .
3-40 Chapter 3: BIOS setup 3.8 Tools menu The T ools menu items allow you to congure options for special functions. Select an item then press <Enter> to display the sub-menu. Select Screen Select Item +- Change Field Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02.
ASUS P6T Deluxe V2 3-41 3.8.2 Express Gate [Enabled] Allows you to enable or disable the ASUS Express Gate feature. The ASUS Express Gate feature is a unique instant-on environment that provides quick access to the Internet browser and Skype. Refer to section 4.
3-42 Chapter 3: BIOS setup 3.8.3 ASUS O.C. Prole This item allows you to store or load multiple BIOS settings. Add Y our CMOS Prole. Allows you to save the current BIOS le to the BIOS Flash.
ASUS P6T Deluxe V2 3-43 3.8.4 Ai Net 2 Check Marvell LAN Cable [Disabled] Enables or disables checking of the Marvell LAN cable during the Power-On Self-T est (POST). Conguration options: [Disabled] [Enabled] v02.61 (C)Copyright 1985-2008, American Megatrends, Inc.
3-44 Chapter 3: BIOS setup Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit. 3.9 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
4 Software support This chapter describes the contents of the support DVD that comes with the motherboard package and the software..
ASUS P6T Deluxe V2 Chapter summary 4 4.1 Installing an operating system ................................................... 4-1 4.2 Support DVD information ............................................................ 4-1 4.3 Software information .....
ASUS P6T Deluxe V2 4-1 If Autorun is NOT enabled in your computer , browse the contents of the support DVD to locate the le ASSETUP .EXE from the BIN folder . Double-click the ASSETUP .EXE to run the DVD. 4.1 Installing an operating system This motherboard supports Windows ® XP/ 64-bit XP/ Vista™ operating systems (OS).
4-2 Chapter 4: Software support 4.2.2 Drivers menu The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices.
ASUS P6T Deluxe V2 4-3 4.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll - Installation Wizard for Utilities Installs all of the utilities through the Installation Wizard. Marvell Y ukon VCT Application Installs Marvell Y ukon Virtual Cable T ester Driver .
4-4 Chapter 4: Software support ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in Windows ® environment. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP).
ASUS P6T Deluxe V2 4-5 4.2.4 Make disk menu The Make disk menu contains items to create the Intel ICH10R or Marvell ® 61xx driver disk. Intel ICH10R 32/64 bit RAID/AHCI Driver Disk Allows you to create an ICH10R 32/64bit RAID/AHCI driver disk.
4-6 Chapter 4: Software support 4.2.5 Manual menu The Manual menu contains a list of supplementary user manuals. Click an item to open the folder of the user manual. Most user manual les are in Portable Document Format (PDF). Install the Adobe ® Acrobat ® Reader from the Utilities menu before opening a user manual le.
ASUS P6T Deluxe V2 4-7 ASUS TurboV ASUS EPU 6-Engine ASUS Express Gate SSD Browse this DVD Displays the support DVD contents in graphical format. 4.2.7 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support DVD.
4-8 Chapter 4: Software support T echnical support Form Displays the ASUS T echnical Support Request Form that you have to ll out when requesting technical support.
ASUS P6T Deluxe V2 4-9 4.3 Software information Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme le that came with the software application for more information.
4-10 Chapter 4: Software support 9. When the screen returns to the ASUS Update utility , ash the original BIOS to load the new boot logo. 10. After ashing the BIOS, restart the computer to display the new boot logo during POST . 8. Adjust the boot image to your desired size by selecting a value on the Ratio box.
ASUS P6T Deluxe V2 4-1 1 3. Click the Run button to perform a cable test. 4.3.2 AI NET2 The AI NET2 features the Marvell ® Virtual Cable T ester™ (VCT). VCT is a cable diagnostic utility that reports LAN cable faults and shorts using the T ime Domain Reectometry (TDR) technology .
4-12 Chapter 4: Software support 4.3.3 ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others.
ASUS P6T Deluxe V2 4-13 Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show . When displayed, the monitor panel for that sensor also turns red. Refer to the Monitor panels section for details.
4-14 Chapter 4: Software support Changing the monitor panels position T o change the position of the monitor panels in the desktop, click the arrow down button of the Scheme options, then select another position from the list box. Click OK when nished.
ASUS P6T Deluxe V2 4-15 Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below . Large display Small display WMI browser Click to display the WMI (Windows Management Instrumentation) browser .
4-16 Chapter 4: Software support PCI browser Click to display the PCI (Peripheral Component Interconnect) browser . This browser provides information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information.
ASUS P6T Deluxe V2 4-17 Memory usage The Memory tab shows both used and available physical memory . The pie chart at the bottom of the window represents the used (blue) and the available physical memory . Conguring PC Probe II Click to view and adjust the sensor threshold values.
4-18 Chapter 4: Software support 4.3.4 ASUS AI Suite ASUS AI Suite allows you to launch EPU—6 Engine, AI Nap, Fan Xpert, and T urboV utilities easily . Installing AI Suite T o install AI Suite on your computer: 1. Place the support DVD to the optical drive.
ASUS P6T Deluxe V2 4-19 Other feature buttons Click on right corner of the main window to open the monitor window . Click on right corner of the expanded window to switch the temperature from degrees Centigrade to degrees Fahrenheit.
4-20 Chapter 4: Software support 4.3.5 ASUS AI Nap This feature allows you to minimize the power consumption of your computer whenever you are away . Enable this feature for minimum power consumption and a more quiet system operation.
ASUS P6T Deluxe V2 4-21 4.3.6 ASUS Fan Xpert Asus Fan Xpert intelligently allows you to adjust both the CPU and chassis fan speeds according to different ambient temperatures caused by dif ferent climate conditions in different geographic regions and your PC’s system loading.
4-22 Chapter 4: Software support Click to get the calibration between the fan rotation and fan speed ratio Click to close the Calibration window Fan prole modes • Disable: Select this mode to disable the Fan Xpert function. • Standard: This mode makes the fan adjust speed in moderate pattern.
ASUS P6T Deluxe V2 4-23 4.3.7 ASUS EPU–6 Engine ASUS EPU–6 Engine is an energy-efcient tool that satises different computing needs. This utility provides four modes that you can select to enhance system performance or save power . Selecting Auto mode will have the system shift modes automatically according to current system status.
4-24 Chapter 4: Software support *• Click Current to show the CO2 that has been reduced since you click the Renew button . *• Click T otal to show the total CO2 that has been reduced since you launched 6 Engine. 6 Engine main menu Auto Mode Runs calibration T urbo Mode High Performance Mode Medium Power Saving Mode Max.
ASUS P6T Deluxe V2 4-25 Click to select a mode Move the slider to adjust Click the arrow to see more options Restore default settings Click to apply settings Click to abort settings Conguration options in Advanced settings menu The following lists the conguration options and their denitions in Advanced settings menu.
4-26 Chapter 4: Software support Conguration options T urbo Mode High Performance Mode Medium Power Saving Mode Maximum Power Saving Mode CPU Frequency Overclocking +1% to +30% N/A Downclocking -1%.
ASUS P6T Deluxe V2 4-27 4.3.8 ASUS T urboV ASUS T urboV allows you to overclock the CPU frequency , CPU voltage, QPI/ Memory controller voltage, and DRAM voltage in WIndows ® environment and takes effect in real-time without exiting and rebooting the OS.
4-28 Chapter 4: Software support Advanced settings menu Click More Setting from the T urboV main screen to display detailed conguration options for CPU/chip voltage, DRAM Reference voltage, and CPU ratio. • Only Intel ® Core™ i7 Extreme Edition processors support the CPU Ratio function.
ASUS P6T Deluxe V2 4-29 4.3.9 SoundMAX ® High Denition Audio utility The ADI AD2000B High Denition Audio CODEC provides 8-channel audio capability through the SoundMAX ® audio utility with AudioESP™ software to deliver the ultimate audio experience on your PC.
4-30 Chapter 4: Software support Setup The Setup tab allows you to adjust multi-speaker settings. Click speaker to test individual speaker volume Click to swap center/subwoofer output in 5.
ASUS P6T Deluxe V2 4-31 Recording Experience The Recording Experience tab allows you to calibrate microphone settings for high quality recording effects.
4-32 Chapter 4: Software support Jack conguration This screen helps you congure your computer’s audio ports, depending on the audio devices you have installed. B. SoundMAX audio utility for Windows XP™ Audio Setup Wizard By clicking the icon from the SoundMAX ® control panel, you can easily congure your audio settings.
ASUS P6T Deluxe V2 4-33 Adjust speaker volume This screen helps you adjust speaker volume. Click the T est button to hear the changes you have made. Adjust microphone volume This screen helps you adjust microphone volume. Y ou will be asked to read pre-written text to allow the AudioWizard to adjust the volume as you speak.
4-34 Chapter 4: Software support Microphone options Click the Microphone tab allows you to optimize your microphone input settings. Enhanced Microphone Features V oice recording Enables Noise Filter function.
ASUS P6T Deluxe V2 4-35 4.3.10 ASUS Express Gate SSD ASUS Express Gate SSD is an instant-on environment that gives you quick access to web, Skype, and viewing your pictures. Within a few seconds of powering on your computer , you will be at the Express Gate SSD menu where you can start the web browser , Skype, or other Express Gate applications.
4-36 Chapter 4: Software support Knowing the Express Gate hot-keys Here is a list of common-used hot-keys for Express Gate. In the First Screen: Key Function P AUSE/BREAK Power-off ESC/F8 Continue to .
ASUS P6T Deluxe V2 4-37 Using the Conguration Panel Use the conguration panel to change various Express Gate SSD settings. Click on an icon to open a particular conguration tool. The following tools are available: • Date and Time: set current date and time as well as time zone.
4-38 Chapter 4: Software support Using the LaunchBar The LaunchBar has several system icons that show you various system statuses and let you congure individual Express Gate SSD settings. The LaunchBar can be congured to auto-hide, if you want more screen space for the softwares.
ASUS P6T Deluxe V2 4-39 Click to change LaunchBar options (auto-hide, docking position, etc). Click to show the “ASUS Utility” panel (if supported). Click to show “About Express Gate SSD”. Click to open Express Gate SSD Help. Click to bring up power options window to boot to OS, restart or power down.
4-40 Chapter 4: Software support • If you use a network cable connected to a home router (which is then connected to your DSL/cable modem), enable every LAN port(s). Express Gate SSD will automatically use whichever port is connected. • The number of the LAN ports may differ from motherboards.
ASUS P6T Deluxe V2 4-41 Using the Photo Manager Express Gate SSD provides a easy-to-use Photo Manager that allows you to view pictures stored in your hard drive or external storage devices (such as USB dongles, card readers, or optical disks).
4-42 Chapter 4: Software support Conguring Express Gate in BIOS Setup Enter BIOS setup by pressing DEL key after powering on or by clicking on the BIOS setup icon on Express Gate’s rst screen. Express Gate conguration options are under T ools conguration menu page.
ASUS P6T Deluxe V2 4-43 The Updater can preserve your Express Gate settings and personal data (web browser bookmarks, etc.) while doing an update. Use the checkbox “Keep user prole” to decide whether the Updater should do so.
4-44 Chapter 4: Software support 4.4 RAID congurations The motherboard comes with the Intel ® ICH10R Southbridge controller that supports RAID 0, RAID 1, RAID 10, and RAID 5 for six independent Serial A T A channels.
ASUS P6T Deluxe V2 4-45 4.4.3 Intel ® RAID congurations This motherboard supports RAID 0, RAID 1, RAID 5, RAID 10 and Intel ® Matrix Storage congurations for Serial A T A hard disks drives through the Intel ® ICH10R Southbridge chip.
4-46 Chapter 4: Software support Intel ® Matrix Storage Manager option ROM utility The Intel ® Matrix Storage Manager Option ROM utility allows you to create RAID 0, RAID 1, RAID 10 (RAID 0+1), and RAID 5 set(s) from Serial A T A hard disk drives that are connected to the Serial A T A connectors supported by the Southbridge.
ASUS P6T Deluxe V2 4-47 Creating a RAID 0 set (striped) T o create a RAID 0 set: 1 . From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. 2. Enter a name for the RAID 0 set and press <Enter>.
4-48 Chapter 4: Software support 6. Use the up/down arrow key to select the stripe size for the RAID 0 array , and then press <Enter>. The available stripe size values range from 4 KB to 128 KB.
ASUS P6T Deluxe V2 4-49 Creating a RAID 1 set (mirrored) T o create a RAID 1 set: 1 . From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. 2. Enter a name for the RAID 1 set and press <Enter>.
4-50 Chapter 4: Software support Creating a RAID 10 set (RAID 0+1) T o create a RAID 10 set: 1 . From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. 2. Enter a name for the RAID 10 set and press <Enter>.
ASUS P6T Deluxe V2 4-51 Creating a RAID 5 set (parity) T o create a RAID 5 set: 1 . From the utility main menu, select 1. Create RAID V olume and press <Enter>. The following screen appears. WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 7.
4-52 Chapter 4: Software support 4. The Disks item is highlighted, press <Enter> to select the hard disk drives to congure as RAID. The following screen appears. 5. Use the up/down arrow key to highlight the drive you want to set, and then press <Space> to select.
ASUS P6T Deluxe V2 4-53 4.5.2 Creating a RAID driver disk in Windows ® T o create a RAID driver disk in Windows ® : 1. Start Windows ® . 2. Place the motherboard support DVD into the optical drive. 3. Go t o t he Make disk menu, and then click Intel ICH10R 32/64 bit RAID Driver Disk to create an Intel ® ICH10R RAID driver disk.
4-54 Chapter 4: Software support T o install the RAID driver in Windows XP: 1. During the OS installation, the system prompts you to press the <F6> key to install third-party SCSI or RAID driver . 2. Press <F6> then insert the oppy disk with RAID driver into the oppy disk drive.
5 Multiple GPU technology support This chapter describes how to install and congure multiple A TI ® CrossFireX™ and NVIDIA SLI™ graphics cards.
ASUS P6T Deluxe V2 Chapter summary 5 5.1 A TI ® CrossFireX™ technology .................................................... 5-1 5.2 Installing CrossFireX™ graphics cards ..................................... 5-2 5.3 Software information .........
ASUS P6T Deluxe V2 5-1 5.1 ATI ® CrossFireX™ technology The motherboard supports the A TI ® CrossFireX™ technology that allows you to install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section.
5-2 Chapter 5: Multiple GPU technology support 4. Align and rmly insert the CrossFireX bridge connector to the goldngers on each graphics card. Ensure that the connector is rmly in place. 5.2 Installing CrossFireX™ graphics cards • Ensure that your power supply unit (PSU) can provide at least the minimum power required by your system.
ASUS P6T Deluxe V2 5-3 5. Connect two independent auxiliary power sources from the power supply to the two graphics cards separately . 6. Connect a VGA or a DVI cable to the graphics card. 5.2.2 T riple CrossFireX installation 1. Prepare three CrossFireX-ready graphics cards.
5-4 Chapter 5: Multiple GPU technology support 5.3 Software information 5.3.1 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers. • Ensure that your PCI Express graphics card driver supports the A TI ® CrossFireX™ technology .
ASUS P6T Deluxe V2 5-5 Enabling Dual CrossFireX technology 1. In the Catalyst Control Center window , click Graphics Settings > CrossFireX > Congure . 2. From the Graphics Adapter list, select the graphics card to act as the display GPU. 3. Select Enable CrossFireX .
5-6 Chapter 5: Multiple GPU technology support 5.4 NVIDIA ® SLI™ Technology The motherboard supports the NVIDIA ® SLI™ (Scalable Link Interface) technology that allows you to install up to two identical PCI Express™ x16 graphics cards. Follow the installation procedures in this section.
ASUS P6T Deluxe V2 5-7 5.4.3 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers.
5-8 Chapter 5: Multiple GPU technology support (B2) From the Personalization window , select Display Settings . (B3) From the Display Settings dialog box, click Advanced Settings . (B4) Select the NVIDIA GeForce tab, and then click Start the NVIDIA Control Panel .
ASUS P6T Deluxe V2 5-9 (B5) The NVIDIA Control Panel window appears. Enabling SLI conguration From the NVIDIA Control Panel window , select Set SLI Conguration . Click Enable SLI and set the display for viewing SLI rendered content. When done, click Apply .
5-10 Chapter 5: Multiple GPU technology support.
デバイスAsus P6T Deluxe V2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Asus P6T Deluxe V2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsus P6T Deluxe V2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Asus P6T Deluxe V2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Asus P6T Deluxe V2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Asus P6T Deluxe V2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsus P6T Deluxe V2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Asus P6T Deluxe V2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsus P6T Deluxe V2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。