PanasonicメーカーKX-TC1871NZBの使用説明書/サービス説明書
ページ先へ移動 of 96
900MHz Cordless Answering System Model No. KX-TC1871ALB KX-TC1871NZB Operating Instructions PLEASE READ BEFORE USE AND SAVE. Charge the battery for about 6 hours before initial use.
Before Initial Use 2 Thank you for purchasing your new Panasonic cordless telephone. For your future reference Serial No. Date of purchase (found on the bottom of the unit) Name and address of dealer For Australia When you subscribe to Caller ID services from your telephone operator, this telephone will display the caller’s phone number.
For Best Performance 3 Battery Charge A rechargeable Ni-Cd battery powers the handset. Charge the battery for about 6 hours before initial use (p. 15). Clean the handset and the base unit charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity.
Preparation Location of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Settings . . . . . . . . . . . . . . . . . . . . . . .
5 Preparation Cordless Telephone Answering System Useful Information Using the Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Storing Names and Numbers in the Directory . . . . . . . . . . . . . . 49 Steps for Entering Names and Symbols .
Location of Controls 6 Base unit CALLER ID STOP/EXIT NEW MESSAGE ERASE CLEAR EDIT SKIP/FF SEARCH REPEAT/REW GREETING DIRECTORY ABC DEF MNO JKL GHI 1 2 3 4 5 6 7 8 9 0 PQRS VOLUME LOCAT OR REDIAL INTERCOM MIC HOLD RECALL PAUSE RINGER IN USE/CHARGE TUV WXYZ D I G I T A L S P - P H O N E ANSWER ON (RINGER) Button (p.
“ 7 Preparation SPREAD SPECTRUM CALLER ID STOP/EXIT NEW MESSAGE ERASE CLEAR EDIT SKIP/FF SEARCH REPEA T/REW GREETING DIRECTORY ABC DEF MNO JKL GHI 1 2 3 4 5 6 7 8 9 0 PQRS VOLUME LOCAT OR REDIAL INTERCOM MIC HOLD RECALL PAUSE RINGER IN USE/CHARGE TUV WXYZ D I G I T A L S P - P H O N E ANSWER ON (NEWMESSAGE) Button (p.
“ Location of Controls 8 Handset T ALK DIRECT FWD/EDIT BACK FUNCTION/EXIT 1 2 ABC 3 DEF 5 JKL 6 MNO 4 GHI 8 TUV 0 9 WXYZ 7 PQRS RECALL REDIAL P AUSE INTERCOM/CLEAR ON OFF LOUD/ SEARCH CH PLAYBACK REPEAT SKIP P AGER NEW MSG ALL MSG ANS ON STOP ANS OFF Antenna (TALK) Button (p.
Displays “ 9 Preparation Both the handset and the base unit show you instructions and information on the displays. These display prompts are shown below. Common prompts for the handset and the base unit No items stored The Caller List is empty or there are no stored items in the directory.
“ Displays 10 Please lift up and try again Talk 01-06-35 No link to base. Place on cradle and try again. 12 new calls 12 new calls 43 1 =Directory Handset only Recharge battery The battery needs to be charged. Place the handset on the base unit to charge the battery (p.
“ 11 Preparation Remote operation Answering system setting. See base unit. When the ringer volume is set to OFF (p. 21), “ Ringer off ” will flash for about 45 seconds before the unit returns to the standby mode (p. 16). When trying to store an item or Caller List information in the directory, the directory memory is full (p.
“ Displays 12 Base unit only In the standby mode, the display shows the current day and time, the number of new calls and recorded messages. (Ex. 5 new calls have been received and 10 messages have been recorded.) When the clock needs adjusting, the day and time flash (p.
13 Preparation 0222333444 - Answering - SUN 12:00AM 5 new calls Message full SUN 12:00AM 5 new calls 10 messages PAGER SUN 12:00AM Ringer off 10 messages Handset in use The answering system is recording a message (p. 65). (“ – Answering – ” flashes.
Settings 14 Connections Fasten the cords to prevent them from being disconnected. Hooks Raise the antenna. To Power Outlet (AC 230 V–240 V, 50 Hz) AC Adaptor Telephone Line Cord To Socket Telephone Plug OR For New Zealand T o Single-Line T elephone Jack For Australia Telephone Line Cord ≥ USE ONLY WITH Panasonic AC ADAPTOR PQLV1AL.
15 Preparation Installing the Battery in the Handset Install the battery and close the handset cover, locking it into place. IN USE/CHARGE Indicator OR Battery strength You can check the battery strength on the display while the handset is on the base unit, while it is in use (making/answering a call etc.
16 Recharge Recharge the battery when: —“ Recharge battery ” is displayed, —“ ” flashes on the display, or —the handset beeps intermittently while it is in use. ≥ If you DO NOT recharge the handset battery for more than 15 minutes, the display will keep indicating “ Recharge battery ” and/or “ ” will continue to flash.
17 Preparation “ Using the Belt Clip You can hang the handset on your belt or pocket using the belt clip. To attach the belt clip To remove the belt clip Headset Jack When the optional headset is connected to the handset, make sure to use the headset to talk with the caller.
“ Settings 18 Selecting the Line Mode If the line is connected to a low voltage system such as a PBX, set to “B”. Otherwise a second caller’s information may not be displayed (p. 62), and the unit may not alert your pager (p. 70). Your phone comes from the factory set to “A”.
Programmable Functions “ 19 Preparation 1 Save DIRECT# Set recall time Set line mode Talk switching TAD program You can program the following function items using the handset near the base unit . The display shows the programming instructions. See the corresponding pages for function details.
20 Setting the Auto Talk Feature The Auto Talk feature allows you to answer a call by lifting the handset off the base unit without pressing (TALK) . If you want to use this feature, turn the feature ON by programming. Your phone comes from the factory set to OFF.
21 Preparation “ 1 Press (FUNCTION/EXIT/CH) . 2 Press (›) or (‹) repeatedly until the arrow points to “ Ringer volume ”, and press FWD/EDIT (fl) ( Yes key). 3 Press (›) or (‹) to select the desired volume. ≥ The selected volume is displayed and rings.
22 “ Programmable Functions With the base unit Make sure the unit is in the standby mode. ≥ To select HIGH (preset) or LOW , press (RINGER) . Each time you press the button, the ringer volume will change and the selected volume will ring. ≥ To turn the ringer OFF , press and hold (RINGER) until 2 beeps sound.
23 Preparation Preparing the Answering System “ Greeting Message You can record a personal greeting message of up to 2 minutes . If a greeting message is not recorded, one of two pre-recorded greetings will be played when a call is received (p. 24).
“ Preparing the Answering System 24 To erase the recorded greeting message Press (GREETING/EDIT) briefly ¤ Press (ERASE/CLEAR) while the message is being played. ≥ The unit will answer a call with a pre-recorded greeting. Pre-recorded greeting message If you do not record a greeting message (p.
“ 25 Preparation Programming Summary for the Answering System You can program the following functions using the handset near the base unit . See the page numbers below for details. The unit must be in the standby mode before programming. ≥ To cancel during programming, press (FUNCTION/EXIT/CH) .
26 “ Preparing the Answering System Day and Time Adjustment Voice Day/Time Stamp: During playback, a synthesized voice will announce the day and time that each message was recorded. 1 Press (FUNCTION/EXIT/CH) . 2 Press (›) or (‹) repeatedly until the arrow points to “ Program ”.
27 Preparation “ To check the day/time Repeat steps 1 to 6 on page 26. ≥ The current day/time is heard. When finished, press (FUNCTION/EXIT/CH) . For Caller ID service users (p. 36) ≥ The Caller ID information will re-set the clock after the first ring if the adjusted time is incorrect.
28 “ Preparing the Answering System Selecting the Caller’s Recording Time You can select “1 minute”, “3 minutes” or “Greeting only” for the caller’s recording time. Your phone comes from the factory set to “3 minutes”. 1 Press (FUNCTION/EXIT/CH) .
29 Preparation Selecting the Number of Rings You can select the number of times the unit rings before the answering system answers a call, from “2” to “7” or “Toll saver”*. Your phone comes from the factory set to “Toll saver”. 1 Press (FUNCTION/EXIT/CH) .
Making Calls 30 1 Press (TALK) . 2 Dial a phone number. ≥ The dialled number is displayed. ≥ After a few seconds, the display will show the length of the call and the battery strength. 3 To hang up, press (TALK) or place the handset on the base unit.
“ 31 Cordless Telephone To dial after confirming the entered number 1 Dial a phone number. ≥ If you misdial, press (INTERCOM/CLEAR) . All digits are erased. Dial the correct phone number. 2 Press (TALK) . ≥ After a few seconds, the display will show the length of the call and the battery strength.
32 “ Making calls With the Base Unit (Digital Duplex Speakerphone) (DIGITALSP-PHONE) and Indicator (HOLD) VOLUME (_) , (^) (REDIAL) MIC Display 1 Press (DIGITALSP-PHONE) . ≥ The DIGITAL SP-PHONE indicator lights. 2 Dial a telephone number. 3 When the other party answers, talk into the MIC (microphone).
33 Cordless Telephone “ Hands-free Digital Speakerphone For best performance, please note the following: ≥ Talk alternately with the caller in a quiet room. ≥ If the other party has difficulty hearing you, press VOLUME (_) to decrease the speaker volume.
“ Making calls 34 Simultaneous Keypad Dialling You can use the base unit like a standard telephone. After pressing (TALK) to make a call with the handset near the base unit, you can also dial using the base unit keypad. 1 Handset: Press (TALK) . 2 Base unit: Dial a telephone number while hearing a dial tone on the handset.
Answering Calls 35 Cordless Telephone When a call is received, the unit rings and the (CALLER–ID) button on the base unit flashes quickly. If you subscribe to a Caller ID service, the calling party information will be displayed after the first ring (p.
Caller ID Service 36 This unit is compatible with a Caller ID service offered by your telephone company. If you subscribe to a Caller ID service, the calling party’s information will be displayed on the handset and the base unit after the first ring.
37 Cordless Telephone To check the number of new calls When new calls have been received, the (CALLER–ID) button flashes slowly on the base unit. Ex. You have received 10 new calls. (›) , (‹) While the handset is off the base unit: Press (›) or (‹) to turn the display on.
38 Using the Caller List With the handset 1 Lift the handset off the base unit and press (›) or (‹) to enter the Caller List. ≥ The display will show, for example, the following: ≥ You can go to the directory list by pressing FWD/EDIT (fl) (p.
39 Cordless Telephone “ √ : You have checked this caller information, answered the call or called back the caller. k 2 – k 9 : The number of times the same caller called (up to 9). After checking, “ a 2 ”–“ a 9 ” will be replaced with “ √ ”.
“ Using the Caller List 40 Editing the Caller’s Phone Number The unit can edit a phone number into one of 3 patterns. Make sure the unit is in the standby mode. With the handset 1 Lift the handset off the base unit and press (›) or (‹) to enter the Caller List.
“ 41 Cordless Telephone 5 After editing the number, you can continue with calling back or storing procedures. To call back, press (TALK) (p. 39). To store the number in the directory, press (›) ( Next key). Follow the instructions on the display (p.
“ Using the Caller List 42 With the base unit 1 Press (CALLERID) to enter the Caller List. 2 Press (SKIP/FF) or (REPEAT/REW) repeatedly to find the desired caller. 3 Press (GREETING/EDIT) to select a pattern. ≥ Each time you press (GREETING/EDIT) , the number is rearranged into one of 3 different patterns.
“ 43 Cordless Telephone Storing Caller List Information in the Directory You can store numbers that are in the Caller List in the directory. This feature can operate only with the handset. Make sure the unit is in the standby mode. 1 Lift the handset off the base unit and press (›) or (‹) to enter the Caller List.
“ Using the Caller List 44 ≥ You can exit the programming mode any time by pressing (FUNCTION/EXIT/CH) . ≥ If the display shows “ Directory full ” in step 3, the display will return to step 2. Press (FUNCTION/EXIT/CH) to exit the list. To erase other stored items from the directory, see page 58.
With the handset 1 Lift the handset off the base unit and press (›) or (‹) to enter the Caller List. 2 Press (›) or (‹) repeatedly to find the caller you want to erase from the Caller List. 3 Press (INTERCOM/CLEAR) . ≥ A beep sounds and the information is erased.
With the handset 1 Lift the handset off the base unit and press (›) or (‹) to enter the Caller List. 2 Press (INTERCOM/CLEAR) . 3 Press (›) or (‹) to select “ All clear ”. 4 Press FWD/EDIT (fl) ( Yes key) or (INTERCOM/CLEAR) . ≥ A beep sounds and all entries are erased.
47 Cordless Telephone One -Touch Dialler “ A phone number stored in the (DIRECT) button can be dialled with a one-touch operation. Storing a Phone Number in the DIRECT Button Make sure the unit is in the standby mode. 1 Press (FUNCTION/EXIT/CH) . 2 Press (›) or (‹) repeatedly until the arrow points to “ Program ”.
48 “ One-Touch Dialler Dialling the Stored Number in the DIRECT Button 1 Press (TALK) . 2 Press (DIRECT) . ≥ After a few seconds, the display will show the length of the call and the battery strength. To dial after confirming the entered number Press (DIRECT) ¤ (TALK) .
Using the Directory “ 49 Cordless Telephone You can store up to 50 names and phone numbers in the directory. All directory items are sorted by the first word in alphabetical order. Using the directory, you can make a call by selecting a name on the handset or base unit display.
“ Using the Directory 50 1 Press (FUNCTION/EXIT/CH) . 2 While the arrow points to “ Save directory ”, press FWD/EDIT (fl) ( Yes key). ≥ The display shows the number of stored items in the directory. 3 Enter a name, up to 15 characters, with the dialling buttons, BACK (fi) or FWD/EDIT (fl) .
“ 51 Cordless Telephone ≥ If a pause is required for dialling, (REDIAL/PAUSE) can be stored in a phone number counting as one digit (p. 62) in step 5. ≥ You can exit the programming mode any time by pressing (FUNCTION/EXIT/CH) . ≥ If the display shows “ Directory full ” in step 2, the display will return to step 1.
“ Using the Directory 52 (1) (2) (3) (4) (5) (6) (7) (8) (9) (0) BACK (fi) FWD/EDIT (fl) 123456789 1 0 1 1 Number of times key is pressed Steps for Entering Names and Symbols The handset dialling buttons ( (0) to (9) ), BACK (fi) and FWD/EDIT (fl) can be used to enter letters and symbols.
“ 53 Cordless Telephone For example, to enter “Tom Jones”: 1 Press (FUNCTION/EXIT/CH) . 2 While the arrow points to “ Save directory ”, press FWD/EDIT (fl) ( Yes key). 3 Press (8) . 4 Press (6) six times, then press FWD/EDIT (fl) to move the cursor to the right.
Finding Items in the Directory With the handset Make sure the unit is in the standby mode. 1 Press BACK (fi) or FWD/EDIT (fl) to enter the directory list. 2 Press (›) or (‹) . ≥ The first item is displayed. 3 Press (›) or (‹) repeatedly until the desired item is displayed.
“ 55 Cordless Telephone With the base unit Make sure the unit is in the standby mode. 1 Press (DIRECTORY) to enter the directory list. ≥ The first item is displayed. 2 Press (SKIP/FF) or (REPEAT/REW) repeatedly until the desired item is displayed.
“ Using the Directory 56 With the handset 1 Press BACK (fi) or FWD/EDIT (fl) to enter the directory list. 2 Press (›) or (‹) . ≥ The first item is displayed. 3 Press (›) or (‹) repeatedly to find the directory item that you want to dial (p.
“ 57 Cordless Telephone Editing an Item in the Directory This feature can operate only with the handset. Make sure the unit is in the standby mode. 1 Press BACK (fi) or FWD/EDIT (fl) to enter the directory list. 2 Press (›) or (‹) . ≥ The first item is displayed.
“ Using the Directory 58 With the handset 1 Press BACK (fi) or FWD/EDIT (fl) to enter the directory list. 2 Press (›) or (‹) . ≥ The first item is displayed. 3 Press (›) or (‹) repeatedly to find the directory item you want to erase (p.
Intercom “ 59 Cordless Telephone A 2-way intercom is possible between the handset and the base unit. Paging the base unit from the handset 1 Handset: Press (INTERCOM/CLEAR) . Talk to the paged party after the beeps. ≥ “ Intercom ” is displayed.
“ Intercom 60 During an intercom call: ≥ Intercom calls can only be ended with the handset. ≥ If the handset user has difficulty hearing the base unit user, decrease the base unit speaker volume by pressing VOLUME (_) . ≥ If an incoming call is received, the intercom call stops and the unit starts to ring.
Special Features “ 61 Cordless Telephone Automatic Security Code Setting Each time you place the handset on the base unit, the unit automatically selects one of more than a million security codes. These codes help prevent the unauthorized use of your telephone line by another cordless telephone user.
62 “ Special Features How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) We recommend you press (REDIAL/PAUSE) or (PAUSE) if a pause is required for dialling with a PBX or to access a long distance service.
63 Cordless Telephone “ RECALL Button Pressing (RECALL/PLAYBACK) or (RECALL) allows you to use special features of your host PBX such as transferring an extension call or accessing special telephone services (optional) such as call waiting. Selecting the recall time The recall time depends on your telephone exchange or host PBX.
64 “ Special Features 1 Press (FUNCTION/EXIT/CH) . 2 Press (›) or (‹) repeatedly until the arrow points to “ Program ”. 3 Press FWD/EDIT (fl) ( Yes key). 4 Press (›) or (‹) repeatedly until the arrow points to “ Set recall time ”. 5 Press FWD/EDIT (fl) ( Yes key).
65 Answering System Automatic Answering Operation When the unit answers a call, a greeting message is played and the caller’s message is recorded. While recording, “ - Answering - ” will be displayed. ≥ The total recording time (including greeting message) is about 15 minutes .
66 Listening to Messages You can see the total number of recorded messages on the base unit display. If the ANSWER ON indicator flashes, new messages have been recorded. Listening to only new messages Press (NEWMESSAGE) briefly. ≥ The unit announces the number of new messages and plays them back.
To repeat from the beginning of the message Press (REPEAT/REW) briefly. ≥ If you press within 5 seconds of playback, the previous message will be played. To rewind part of the message Press and hold (REPEAT/REW) until you reach the desired place. ≥ At the beginning of the message, 3 beeps will sound.
68 “ Listening to Messages From the Handset If someone else is in the room and you want to listen to the recorded messages privately, you can use the handset. 1 Handset: Press (RECALL/PLAYBACK) . ≥ The number of new messages is heard on the handset.
69 Answering System Erasing Messages The unit will announce the remaining recording time after playback, if it is less than 5 minutes. New messages cannot be recorded when: —“ Memory full ” is heard. —“ Message full ” is displayed on the base unit.
70 Pager Call This feature allows you to alert your pager when the unit records an incoming message. You can retrieve the message from a touch tone telephone (p. 74). First program the pager number, then set the unit to call the pager. ≥ Consult your pager company to check whether the service alerts your pager automatically or via an operator.
71 Answering System “ * Pager companies require a delay after the pager number and/or the access code is dialled. Contact your pager company regarding the required pause time. Pressing (REDIAL/PAUSE) once creates a 3.5 second delay and counts as one digit.
72 To confirm the stored pager number 1. Press (FUNCTION/EXIT/CH) . 2. Press (›) or (‹) to select “ Calling pager ”. 3. Press FWD/EDIT (fl) ( Yes key). 4. Press (TALK) . ≥ The unit dials the stored pager number. ≥ If the pager does not beep, check your pager by calling it manually to ensure it works.
73 Answering System Setting the Unit to Call a Pager 1 Press (RECALL/PLAYBACK) . ≥ The number of new messages is heard on the handset. 2 Press (3) . ≥ “ ” is displayed on the base unit. ≥ If “ ” is not displayed, the pager number has not been stored.
74 Remote Operation from a Touch Tone Phone You can operate the answering system from any touch tone phone. A synthesized voice menu will guide you on how to operate the unit (p. 76). ≥ To skip the voice menu and operate the unit directly, see page 78.
75 Answering System “ Setting the Remote Code The remote code prevents unauthorized people from accessing your unit and listening to your messages. Choose any 2-digit number (00–99) . The factory preset remote code is “ 11 ”. If you do not program your own remote code, you can use “11”.
76 “ Remote Operation from a Touch Tone Phone Voice Menu The shaded boxes are voice prompts. Press 1 to play back all messages. Press 2 for other functions. Press 1 to play back new messages. Press 2 for other functions. Press 1 to record your message.
77 Answering System “ All Message Playback All recorded messages are played back. At the end of the last message, “ End of final message ” is heard. The unit will announce the remaining recording time if it is less than 5 minutes. New Message Playback Only new messages are played back.
78 “ Remote Operation from a Touch Tone Phone Direct Remote Operation Once you have entered the remote code, you can also control your unit by direct commands instead of using the voice menu.
79 Answering System PAGER CALL ON/OFF ANSWERING SYSTEM OFF (3) (0) ≥ Each time you press (3) , “ On/Off ” is heard and the mode will turn on or off. ≥ If you have not stored a pager number, 6 beeps will sound and the mode will not turn on. ≥ The unit hangs up and will not answer calls until turned on again.
80 Remote Operation with the Handset Voice menu If no commands are entered after you press (RECALL/PLAYBACK) , the unit will start the following voice menu. “ Press 4 to play back new messages. Press 5 to play back all messages. ” ≥ You can enter direct commands even if the voice menu has started.
81 Answering System Direct commands NEW MESSAGE PLAYBACK ALL MESSAGE PLAYBACK REPEAT (During playback) SKIP (During playback) STOP ERASING A SPECIFIC MESSAGE (During playback) ERASING ALL MESSAGES PAGER CALL ON/OFF ANSWERING SYSTEM OFF ANSWERING SYSTEM ON (4) (5) (1) (2) (9) ($) (4) ($) (5) ≥ Only new messages are played back.
82 Wall Mounting This unit can be mounted on a wall. 1 Set the handset holder as shown. 2 Connect the AC adaptor. 3 Tuck the telephone line cord inside the wall mounting adaptor, then push it in the direction of the arrow. ≥ The word “UP” should face upward.
83 Useful Information 2 1 OR Screws 8.5 cm To Telephone Plug and Socket For Australia To Single-Line Telephone Jack For New Zealand OR 4 Install screws using the wall template (see p. 82). Connect the telephone line cord. Mount the unit, then slide down.
Battery Replacement 84 If “ Recharge battery ” is displayed and/or “ ” flashes after being fully charged, replace the battery with a new Panasonic P-P508 battery. To prevent memory loss, replace within 3 minutes. 1 Press the notch on the battery cover firmly and slide it as indicated by the arrow.
Adding Another Phone 85 Useful Information Standard Telephone Telephone Line Cord To Socket (Optional) Telephone Double Adaptor This unit will not function during a power failure. To connect a standard telephone on the same line, use a telephone double adaptor.
Before Requesting Help 86 Problem “ No link to base. Place on cradle and try again. ” is displayed and an alarm tone sounds. Static, sound cuts in/out, fades. Interference from other electrical units. The handset and/or the base unit do not ring. The handset display is blank.
“ 87 Useful Information Problem The unit does not display the caller’s phone number. The handset display goes to the standby mode while viewing the Caller List. When a second call is received during a conversation, the unit does not display the new caller’s phone number.
“ Before Requesting Help 88 Problem The answering system is on, but incoming messages are not recorded. You cannot listen to the recorded messages. “ Message full ” is displayed and the ANSWER ON indicator flashes rapidly, and no new messages are recorded.
“ 89 Useful Information Problem While recording a greeting message, the unit starts to ring and stops recording. During playback, the unit starts to ring and stops playback. The unit does not alert your pager. Cause and Remedy ≥ To answer the call, press (DIGITALSP-PHONE) , or lift the handset off the base unit or press (TALK) .
“ Before Requesting Help 90 Problem You cannot program items, such as the line mode. Previously programmed information is erased. “ Recharge battery ” is displayed, “ ” flashes or the unit beeps intermittently. You charged the battery fully, but “ Recharge battery ” is still displayed and/or “ ” continues to flash.
91 Useful Information Safety Instructions “ Take special care to follow the safety suggestions listed below. Safety 1) The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit.
92 “ Safety Instructions WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE. Medical Consult the manufacture of any personal medical device, such as pacemakers, to determine if they are adequately shielded from external RF (radio frequency) energy.
93 Useful Information For New Zealand Users Only The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
94 Important Information (For Australia only) Instructions to customer Installation Attached to this apparatus is an approval label. This label is evidence that it is a “Permitted Attachment” which has been authorised to be connected to your telephone service.
95 Useful Information If you are satisfied with the operation of your telephone service after plugging in your Permitted Attachment, your installation is completed.
Printed in Japan PQQX12877ZA FF0900HK0 D Kyushu Matsushita Electric Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan.
デバイスPanasonic KX-TC1871NZBの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic KX-TC1871NZBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic KX-TC1871NZBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic KX-TC1871NZBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic KX-TC1871NZBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic KX-TC1871NZBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic KX-TC1871NZBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic KX-TC1871NZBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic KX-TC1871NZBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
