AsusメーカーPR-DLSRの使用説明書/サービス説明書
ページ先へ移動 of 106
Motherboard PR-DLSR User Guide.
ii Checklist Copyright © 2002 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, sto.
iii Features Contents FCC/CDC statements ..................................................................... vi Safety information ......................................................................... vii About this guide .......................
iv Safeguards Contents 2.6 Expansion slots ................................................................ 2-10 2.6.1 Installing an expansion card ................................ 2-10 2.6.2 Configuring an expansion card .............................
v Contents Chapter 5: OS Installation 5.1 Microsoft ® Windows ® NT Server 4.0 ................................... 5-1 5.1.1 LSI ® SCSI Driver Installation .................................. 5-1 5.1.2 Intel ® 82551QM/82544GC LAN Driver Installation .
vi FCC/CDC st atements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide This user guide contains detailed information on the ASUS PR-DLSR motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the PR-DLSR motherboard.
ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates.
x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.
xi PR-DL SR specifications summar y CPU Chipsets Front Side Bus (FSB) Memory Onboard LAN Onboard SCSI Onboard VGA Expansion slot Rear panel I/O Internal connectors BIOS features Form Factor Support CD contents Support for dual Intel ® Xeon ™ processors RCC Grand Champion LE Server 2.
xii.
ASUS PR-DLSR motherboard user guide 1-1 1 . 1 Welcome! The ASUS ® PR-DLSR motherboard delivers a host of new features and latest technologies making it another standout in the long line of ASUS quali.
1-2 Chapter 1: Product introduction 1 .2 Special features 1.2.1 Product highlights Latest processor technology The PR-DLSR motherboard supports dual Intel ® Xeon ™ p rocessors via 604- pin surface mount ZIF sockets .
ASUS PR-DLSR motherboard user guide 1-3 Onboard VGA The A TI Rage-XL PCI-based VGA controller integrates an 8MB display SDRAM to provide onboard video solution. Integrated IDE bridge The motherboard includes two connectors to support an IDE board with dual-channel bus master IDE connectors.
1-4 Chapter 1: Product introduction 1.2.2 V alue-added solutions T emperature, fan, and voltage monitoring The CPU temperature is monitored by the ASUS ASIC to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection.
ASUS PR-DLSR motherboard user guide 1-5 Chassis intrusion detection The motherboard supports chassis intrusion monitoring through the ASUS ASIC. A chassis intrusion event is retained in the system memory for more protection. Smart BIOS The 4Mbit firmware gives an easy-to-use interface that provides more control and protection to the motherboard.
1-6 Chapter 1: Product introduction 1 .3 Motherboard over view Before you install the PR-DLSR motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades.
ASUS PR-DLSR motherboard user guide 1-7 22 23 24 25 26 27 28 29 30 31 32 33 3 1 5 8 9 13 15 20 21 4 2 19 6 12 7 16 18 14 11 10 17.
1-8 Chapter 1: Product introduction Intel ® 82551QM Fast Ethernet controller . This LAN controller fully supports 10BASE-T/100BASE-TX networking protocols. Intel ® 82544GC Gigabit Ethernet controller . This controller is an integrated Ethernet LAN component that supports 1000Mbps, 100Mbps, and 10Mbps data rates.
ASUS PR-DLSR motherboard user guide 1-9 8-pin 12V SSI power connector . This power connector is for an SSI-type power supply . PCI extended power connector . This connector provides the additional power required by PCI cards. Server management daughterboard connectors.
1-10 Chapter 1: Product introduction 8-switch DIP (SW2). This 8-switch Dual Inline Package (DIP) allows you to select the CPU frequency multiple. 64-bit 133/100MHz PCI slot. This PCI expansion slot is for the proprietary riser card with dual PCI-X slots.
Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
ASUS PR-DLSR motherboard Chapter summar y 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) .
ASUS PR-DLSR motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The PR-DLSR uses the extended A TX form factor that measures 12 x 12 inches (30.
2-2 Chapter 2: Hardware information 2.2 Motherboard layout The SCSI features are optional. These components are grayed out in the above motherboard layout. 4Mbit Flash BIOS PR-DLSR PCI1 (Proprietary expansion slot) F AN1 AT I RAGE XL VGA Controller SW2 30.
ASUS PR-DLSR motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component.
2-4 Chapter 2: Hardware information 2.4 Central Pr ocessing Unit (CPU) 2.4.1 Overview The motherboard comes with dual surface mount 604-pin Zero Insertion Force (ZIF) sockets. The sockets are designed for the Intel ® Xeon ™ Processor in the 603/604-pin package.
ASUS PR-DLSR motherboard user guide 2-5 Follow these steps to install a CPU. 1. Locate the 604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 1 15° angle. 2. Position the CPU above the socket as shown.
2-6 Chapter 2: Hardware information 2.4.3 Installing the heatsink Follow these steps to install the CPU heatsink. 1. Carefully place the heatsink on top of the installed CPU. The heatsink fits in only one orientation. T ake note of the heatsink placement as shown.
ASUS PR-DLSR motherboard user guide 2-7 2.5 System memor y 2.5.1 Overview The motherboard comes with six Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 12GB system memory using 184-pin registered PC2100/1600 DDR DIMMs with Serial Presence Detect (SPD) and Error Check and Correction (ECC).
2-8 Chapter 2: Hardware information 2.5.2 Memory Configurations The motherboard supports system memory of up to 12GB in a two-way interleaved or non-interleaved configuration. The two-way interleaved configuration requires that you install identical DDR DIMMs (exactly the same type and size) in pairs.
ASUS PR-DLSR motherboard user guide 2-9 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. Follow these steps to install a DIMM.
2-10 Chapter 2: Hardware information 2.6 Expansion slots This motherboard has a proprietary expansion slot that accommodates a dual slot riser card. The riser card i mplements the PCI-X (Peripheral Component Interconnect Extended) bus technology to support up to 133MHz data transfers, or about 1.
ASUS PR-DLSR motherboard user guide 2-11 Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port.
2-12 Chapter 2: Hardware information 2.7 Switches and jumpers 2.7.1 Switches The following figure shows the location and default settings of the DIP switches on the motherboard.
ASUS PR-DLSR motherboard user guide 2-13 2. CPU Core:Bus frequency multiple (SW2 Switches 1-8) These switches allow you to set the frequency multiple between the CPU internal and external frequencies. This must be set in conjunction with the CPU Bus Frequency .
2-14 Chapter 2: Hardware information 2.7.2 Jumpers 2. SCSI setting (3-pin J5) Set this jumper to pins 1-2 to enable or disable the onboard SCSI controller . Set to pins 2-3 to disable the onboard SCSI controller . 1. Keyboard power setting (3-pin J1) This jumper allows you to enable or disable the keyboard wake-up feature.
ASUS PR-DLSR motherboard user guide 2-15 3. Fast Ethernet setting (3-pin J3) Set this jumper to pins 1-2 to enable the onboard Intel 82551QM Fast Ethernet controller and support 10BASE-T/100BASE-TX networking. Set to pins 2-3 to disable the controller .
2-16 Chapter 2: Hardware information 5. Clear RTC RAM (J7) These solder pads allow you to clear the Real T ime Clock (R TC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
ASUS PR-DLSR motherboard user guide 2-17 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. 2. Serial port 2 connector (10-1 pin COM2) This connector accommodates a second serial port using an optional serial port bracket.
2-18 Chapter 2: Hardware information 3. A TX power connector (24-pin EA TXPWR, 8-pin SSI 12VCON) These connectors are for the 24-pin power plug and the 8-pin 12V power plug from an SSI-type 350W power supply . The plugs from the power supply are designed to fit these connectors in only one orientation.
ASUS PR-DLSR motherboard user guide 2-19 5. CPU, Chassis, and Power Fan Connectors (3-pin F AN1, F AN2, F AN4) (8-pin SYSF AN1, SYSF AN2) The motherboard has six fan connectors to support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.
2-20 Chapter 2: Hardware information 6. Ultra160 SCSI connector (SCSIB) This motherboard has two 68-Pin Ultra160 SCSI connectors, one internal and one external. The SCSI connectors can support a maximum of 15 devices as specified by Ultra160 standards.
ASUS PR-DLSR motherboard user guide 2-21 7. Backplane bridge connectors (BPCON) These connectors are for the backplane bridge board that connects the motherboard to the backplane board. The backplane connectors support two kinds of bridge board as shown below .
2-22 Chapter 2: Hardware information.
Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes..
ASUS PR-DLSR motherboard Chapter summar y 3.1 Starting up for the first time .......................... 3-1 3.2 Powering off the computer .............
ASUS PR-DLSR motherboard user guide 3-1 3. 1 St ar ting up for the fir s t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis.
3-2 Chapter 3: Powering up 3.2 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system.
Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
ASUS PR-DLSR motherboard Chapter summar y 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-5 4.3 Main Menu ...................................................... 4-8 4.4 Advanced Menu .
ASUS PR-DLSR motherboard user guide 4-1 4.1.1 Creating a bootable disk AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard.
4-2 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears.
ASUS PR-DLSR motherboard user guide 4-3 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3.
4-4 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears.
ASUS PR-DLSR motherboard user guide 4-5 4.2 BIOS Setup progr am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 4.
4-6 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features.
ASUS PR-DLSR motherboard user guide 4-7 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination.
4-8 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59).
ASUS PR-DLSR motherboard user guide 4-9 Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>. T ype in a password then press <Enter>.
4-10 Chapter 4: BIOS Setup 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu.
ASUS PR-DLSR motherboard user guide 4-11 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM d.
4-12 Chapter 4: BIOS Setup T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity .
ASUS PR-DLSR motherboard user guide 4-13 SMART Monitoring [Disabled] This field allows you to enable or disable the S.M.A.R.T . (Self-Monitoring, Analysis and Reporting T echnology) system that utilizes internal hard disk drive monitoring technology .
4-14 Chapter 4: BIOS Setup 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [12/Sec] This controls the speed at which the system registers repeated keystrokes.
ASUS PR-DLSR motherboard user guide 4-15 4.4 Advanced Menu CPU Speed This field displays the auto-detected CPU speed. CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default [Enabled] or choose [Disabled] to turn on or of f the CPU Level 1 and Level 2 built-in cache.
4-16 Chapter 4: BIOS Setup OS/2 Onboard Memory > 64M [Disabled] When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled].
ASUS PR-DLSR motherboard user guide 4-17 4.4.1 Chip Configuration V ideo Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor . It can greatly improve the display speed by caching the display data.
4-18 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes.
ASUS PR-DLSR motherboard user guide 4-19 4.4.3 PCI Configuration Slot 1, Slot 2, Slot 3, Slot 4 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use.
4-20 Chapter 4: BIOS Setup Onboard SCSI BIOS [Auto] [Auto] allows the motherboard BIOS to detect whether you have a Adaptec SCSI controller . If the SCSI controller is detected, the SCSI BIOS will be enabled. If no SCSI controller is detected, the onboard SCSI BIOS will be disabled.
ASUS PR-DLSR motherboard user guide 4-21 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features.
4-22 Chapter 4: BIOS Setup V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features.
ASUS PR-DLSR motherboard user guide 4-23 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system of f. [Previous State] sets the system back to the state it was before the power interruption.
4-24 Chapter 4: BIOS Setup Power Up on PCI Card [Disabled] This field allows you to boot your computer from another computer by sending a wake-up frame or signal to the LAN card, or the PCI modem card if present.
ASUS PR-DLSR motherboard user guide 4-25 4.5.2 Hardware Monitor MB Temperature [xxxC/xxxF] CPU1 Temperature [xxxC/xxxF] CPU2 Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. If necessary , set to [Ignore] by pressing Enter .
4-26 Chapter 4: BIOS Setup 4.6 Boot Menu The motherboard BIOS supports the BIOS Boot Specification (BBS) version 1.01. BBS is an intelligent mechanism that provides flexible ways to set boot sequence for Initial Program Load (IPL) devices such as CD-ROMs, network remote boot ROM, and SCSI or RAID controllers on PnP cards.
ASUS PR-DLSR motherboard user guide 4-27 3rd Boot : (BEV) [<0> Intel Corporation] This field allows you to select a Bootstrap Entry V ector (BCV) device to boot from. BEV devices include network controllers or cards. The BEV devices present in the system will appear as options for this field.
4-28 Chapter 4: BIOS Setup 4.7 Ser ver Menu DRAM Hot Spare [Disabled] This field allows you to allocate rows of SDRAM for hot spare. Configuration options: [Disabled] [1 row] [2 rows] [3 rows] Remote Console [Disabled] This field allows the text mode VGA display to be sent out to VT100 terminal through COM1.
ASUS PR-DLSR motherboard user guide 4-29 4.8 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup.
4-30 Chapter 4: BIOS Setup Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values.
Chapter 5 OS Installation This chapter tells how to install SCSI, LAN, and VGA drivers for various operating systems..
ASUS PR-DLSR motherboard Chapter summar y 5.1 Microsoft Windows NT Server 4.0 ................ 5-1 5.2 Microsoft Windows 2000 Server ................... 5-9 5.3 Microsoft Windows XP Professional .......... 5-16 5.4 Novell NetW are Server .............
ASUS PR-DLSR motherboard user guide 5-1 5. 1 Micr osof t ® W indows ® NT Ser ver 4.0 5.1.1 LSI ® SCSI Driver Installation Windows NT 4.0 do not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows NT 4.0 installation.
5-2 Chapter 5: OS Installation 3. When prompted for the manufacturer-supplied hardware support disk, insert the appropriate LSI driver disk containing the Windows NT driver required to support your LSI adapter(s) and press Enter .
ASUS PR-DLSR motherboard user guide 5-3 9. Depending on the driver being installed, Symbios Ultra3 PCI SCSI Driver is shown highlighted. Press Enter to proceed. 10. The Windows NT Workstation Setup window reappears. If using an IDE CD-ROM Drive for installation, press S to load additional drives.
5-4 Chapter 5: OS Installation 10. The System Settings Change message displays: “Y ou must restart your computer before the new settings take effect. Do you want to restart your computer now?” Click on the Y es button to restart and reboot Windows NT .
ASUS PR-DLSR motherboard user guide 5-5 B. New System Installation 1. When the Installing Windows NT Networking screen appears, press Next to display the following screen. 2. Check the Wired to the Network box, then click Next . 3. On the screen that appears, click the button Select from list.
5-6 Chapter 5: OS Installation 8. Click Select from list... , then click Have Disk... 9. T ype A: in the dialog box, then click OK. 10. In the following screen, select Intel(R) PRO/1000 Family Adapter , then click OK. Follow the succeeding screen instructions.
ASUS PR-DLSR motherboard user guide 5-7 C. Existing System Installation 1. Double-click the Network icon in the Control Panel. 2. Select the Adapter tab, then click Add . A list of adapters appears. 4. Do not select an adapter from the list. Instead, insert the LAN driver disk that you created from the AP1600R support CD.
5-8 Chapter 5: OS Installation 5.1.3 A TI ® Rage XL Display Driver Installation 1. Insert the ASUS AP1600R support CD into your CD-ROM drive. 2. If Autorun in enabled in your computer , the following screen appears. Click on A TI Rage XL Display Driver to install the driver .
ASUS PR-DLSR motherboard user guide 5-9 5.2 Microsof t ® Windows ® 2000 Ser ver 5.2.1 LSI ® SCSI Driver Installation A. Preparing an LSI Driver Disk The drivers are located on AP1600R support CD at: DriversSdmsDriversW in2k Copy all the files and subdirectory under the Win2k subdirectory to the root directory of a clean floppy disk.
5-10 Chapter 5: OS Installation 4. The appropriate driver is shown highlighted. Press Enter to proceed. 5. Return to the Windows 2000 Setup screen. Press Enter to proceed. The message about setup loading files appears. At this point, simply follow the Microsoft Windows 2000 installation procedure.
ASUS PR-DLSR motherboard user guide 5-11 Drivers are digitally signed by the Microsoft Windows Hardware Quality Lab (WHQL). Due to the delay between the general customer release by LSI Logic of Windows drivers and the completion of WHQL testing, some drivers that are distributed with adapters or downloaded from the LSI Logic web site at www .
5-12 Chapter 5: OS Installation 5.2.2 Intel ® 82551QM/82544GC LAN Driver Installation Y ou may install the Intel 82551QM/82544GC LAN drivers directly from the NR-LSR support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.
ASUS PR-DLSR motherboard user guide 5-13 When done, your Computer Management window shows the installed LAN adapters. 3. Highlight the Intel(R) 82554GC-based Network Connection , click the right mouse button, and select Properties to display the following.
5-14 Chapter 5: OS Installation Y ou may also update the LAN drivers from the LAN Driver Disk if you created one. Follow these steps to update from the LAN driver disk. 1. Boot Windows 2000 system and log on as Administrator . 2. Click on the Start button.
ASUS PR-DLSR motherboard user guide 5-15 5.2.4 Enabling A T A100 Feature in Windows ® 2000 T o enable the A T A100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2. 5.2.3 A TI ® Rage XL Display Driver Installation Windows 2000 system can automatically recognize the A TI RAGE XL PCI driver during system installation.
5-16 Chapter 5: OS Installation 5.3 Microsof t ® W indows ® XP Professional Windows XP contains default drivers to support Intel 82551QM chipset, A TI Rage XL chipset, and LSI 53C1010R SCSI controller . For Windows XP Professional users, we recommended that you use the Intel 82551QM/82544GC drivers from the AP1600R support CD.
ASUS PR-DLSR motherboard user guide 5-17 5. Follow the succeeding installation instructions. 6. When done, the following screen appears. Click Finish to complete the installation.
5-18 Chapter 5: OS Installation 5.4 Novell ® NetWare ® Ser ver 5.4.1 LSI ® SCSI Driver Installation A single driver (*HAM) is provided for the Novell NetW are 4.2 environment. This document explains how to install and use the SDMS NWP A SCSI Host Adapter Module (HAM) driver for NetW are.
ASUS PR-DLSR motherboard user guide 5-19 C. NetW are 4.2 New Installations 1. Begin the file server installation according to the instructions in the file server installation chapter in the Novell NetW are Installation Manual.
5-20 Chapter 5: OS Installation 5.4.2 Intel ® 82551QM/82544GC LAN Driver Installation A. Preparing Intel 82551QM/82544GC LAN Driver Disk 1. Use the self-extracting image files. For the Intel(R) PRO/100 Server Adapter driver , the executable file is located here: DriversLanmakediskmakenw .
ASUS PR-DLSR motherboard user guide 5-21 B. NetW are 4.2 and 6.0 Installations 1. Prepare the Intel(R) PRO/100 Server Adapter driver from the previous section.
5-22 Chapter 5: OS Installation 5.5 Linux RedHat 7 .3 5.5.1 LSI ® SCSI Driver Installation The RedHat 7.3 system can automatically detect the drivers for the LSI 53C1010R controller . 5.5.2 Intel 82551QM/82544GC LAN Driver Installation The RedHat 7.3 system can automatically detect the Intel 82551QM/ 82544GC network controller during installation.
デバイスAsus PR-DLSRの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Asus PR-DLSRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsus PR-DLSRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Asus PR-DLSRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Asus PR-DLSRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Asus PR-DLSRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsus PR-DLSRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Asus PR-DLSRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsus PR-DLSRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。