PanasonicメーカーPT-AE200Uの使用説明書/サービス説明書
ページ先へ移動 of 34
TQBJ 0115-2 LCD Pr ojector Operating Instructions Model No. PT -AE300U PT -AE200U R P C POWER LIGHT INPUT ENTER MENU FREEZE NORMAL ASPECT USER MEMORY VOLUME PICTURE MODE SD MUTE SD TIME MENU LCD PROJECTOR V I D E O C M P N T COMPONENT KEYSTONE Before operating this product, please read the instructions carefully and save this manual for future use.
2-E NGLISH E NGLISH -3 Preparation CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician.
E NGLISH -5 Preparation Precautions with regar d to saf ety W ARNING If a problem occurs (such as no image or no sound) or if you notice smoke or a strange smell coming from the projector, turn off the power and disconnect the power cord from the wall outlet.
E NGLISH -7 Preparation 6-E NGLISH B Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result. Replacement of the lamp unit should only be carried out by a qualified technician.
E NGLISH -9 Preparation 8-E NGLISH Use only the specified battery. B If an incorrect battery is used, it may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Do not mix old and new batteries.
E NGLISH -11 Preparation 10-E NGLISH About the SD memory card slot Make sure that there are no foreign objects inside the slot when inserting an optional SD memory card. Failure to observe it may damage the card and the slot. About the screen If the screen you are using is dirty, damaged or discolored, attractive projections cannot be obtained.
E NGLISH -13 Preparation 12-E NGLISH # Air outlet port Do not cover this port. W ARNING Do not bring your hands or other objects close to the air outlet port. B Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result.
E NGLISH -15 Preparation 14-E NGLISH + KEYSTONE buttons (pages 28 and 29) This button is used to correct keystone distortion of the projected image when the projector position is tilted upward or downward. , NORMAL button (page 27) This button is used to reset the projector adjustment values to the factory default settings.
E NGLISH -17 Preparation 16-E NGLISH <Connector panel> <PT-AE300U> <PT-AE200U> # $ %& ' ( $% ' # ( # AUDIO L-R input jacks (page 18) $ VIDEO input jack (page 18) This jack is used to input video signals from a video equipment such as a video deck.
18-E NGLISH E NGLISH -19 Preparation Example of connecting to video equipment DVD player Video deck NOTE: B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if you wish to change the audio input source, you will need to remove and insert the appropriate plugs.
20-E NGLISH E NGLISH -21 Preparation Setting-up Pr ojection methods The projector can be set up so that any one of the following four projection methods can be used. Select whichever projection method matches the setting-up method. (The projection method can be set from the OPTION menu.
22-E NGLISH E NGLISH -23 P C POWER LIGHT INPUT ENTER MENU FREEZE NORMAL ASPECT USER MEMORY VOLUME PICTURE MODE SD MUTE SD TIME MENU V I D E O C M P N T COMPONENT KEYSTONE P C POWER LIGHT INPUT ENTER M.
24-E NGLISH E NGLISH -25 Basic Operation When a YP B P R signal is being input or SD CARD is selected When a PC/DVI signal is being input * “GAMMA ADJUST” is not displayed by PT-AE200U. * “W-BAL R”, “W-BAL G” and “W-BAL B” are not displayed when DVI signal is being input.
26-E NGLISH E NGLISH -27 Basic Operation Returning a setting to the factory default If you press the NORMAL button on the remote control unit, you can return settings to the factory default settings. However, the operation of this function varies depending on which screen is being displayed.
28-E NGLISH E NGLISH -29 Basic Operation NOTE: B You can also correct keystone distortion by selecting the KEYSTONE item in the MAIN MENU and pressing ENTER. B Vertical and horizontal keystone distortion can be corrected to ±30° of the angle of tilt by PT-AE300U.
30-E NGLISH E NGLISH -31 Basic Operation Setting the ASPECT This projector allows you to change the aspect ratio to match the type of input signal. Pressing the ASPECT button will change the aspect ratio according to the successive settings shown below.
32-E NGLISH E NGLISH -33 Basic Operation Changing the displa y langua ge Indicates the language which is currently set # Select LANGUAGE from the MAIN MENU screen and then press the ENTER button. $ Use the FG buttons to select a language and then press the ENTER button.
34-E NGLISH E NGLISH -35 Basic Operation TINT (NTSC/NTSC 4.43/YP B P R /SD CARD only) This adjusts the flesh tones in the picture. Press the H button to make flesh tones more greenish, and press the I button to make the flesh tones more reddish.
36-E NGLISH E NGLISH -37 Basic Operation Pr ojecting sRGB- compatible pictures sRGB is an international color reproduction standard (IEC61966-2- 1) established by the International Electrotechnical Commission (IEC). If you would like the colours in sRGB-compatible pictures to be reproduced more faithfully, make the following settings.
38-E NGLISH E NGLISH -39 Basic Operation Adv anced Operation Option settings Use the F and G buttons to select an item, then press the I or H buttons to change the setting. OSD ON The signal name is displayed in the top-right corner of the screen when the input signal is changed.
40-E NGLISH E NGLISH -41 Adv anced Operation 4:3 H-POS (4:3 aspect mode only) This sets the horizontal positioning of the projected image when the 4:3 aspect ratio is selected. (Refer to page 31.) FR ONT/REAR This setting should be changed in accordance with the projector setting-up method.
42-E NGLISH E NGLISH -43 Adv anced Operation Inser ting and remo ving the SD memory card About the SD menu The still image data and moving image data that is stored on SD memory cards can be played back using the SD menu. Displa ying the SD menu Press the SD button to change the display to the SD CARD screen.
44-E NGLISH E NGLISH -45 Adv anced Operation Pla ying bac k still ima ges The PICTURE option lets you play back still image data. Slide pla ybac k of still ima ges “SLIDE SHOW” lets you play back still images in a certain order using one of three available playback methods.
46-E NGLISH E NGLISH -47 Adv anced Operation SETTING1 MANUAL MODE NEW USER SET AUTO MODE SETTING USER SET If adding settings for a new user, use the I and H buttons to select “NEW” and then press the ENTER button. The user setting edit screen will then be displayed.
48-E NGLISH E NGLISH -49 Adv anced Operation SETUP This describes how to set the playback interval and angle of rotation for still images in the user settings. # Use the F , G , I and H buttons to select a still image from the user settings, and then press the ENTER button.
50-E NGLISH E NGLISH -51 Adv anced Operation Others Indicator s There are two indicators on the control panel of the projector which give information about the operating condition of the projector.
52-E NGLISH E NGLISH -53 Others Cleaning and replacing the air filter If the air filter becomes clogged with dust, the internal temperature of the projector will rise, the TEMP indicator will flash and the projector power will turn off.
54-E NGLISH E NGLISH -55 Others Lamp unit replacement pr ocedure NOTE: B If the lamp usage time has passed 2000 hours (when LAMP POWER has been set to “HIGH”), the projector will switch to standby mode after approximately 10 minutes of operation. The steps * to - on the next page should thus be completed within 10 minutes.
56-E NGLISH E NGLISH -57 Others Bef ore calling f or service Before asking for service, check the following points. Problem Possible cause Power does not turn on. No picture appears. The picture is fuzzy. COLOR is too light or TINT is poor No sound can be heard.
58-E NGLISH E NGLISH -59 Others Specifications Power supply: 100 V–240 V ~, 50 Hz/60 Hz Power consumption: 180 W (During standby (when fan is stopped): Approx.
60-E NGLISH E NGLISH -61 Others Appendix List of compatible signals *1 The “i” appearing after the resolution indicates an interlaced signal. *2 The following symbols are used to indicate picture quality. AA Maximum picture quality can be obtained.
62-E NGLISH E NGLISH -63 Others Pin No. Signal # Earth (Luminance signal) Earth (Color signal) Luminance signal Color signal $ % & B The pin layout and signal names for the RGB input connector are shown below. Pin No. Signal # R G/G·SYNC B SDA $ % .
64-E NGLISH E NGLISH -65 Others DCF standar d This projector can only play back image files which comply with the DCF specification. The DCF specification imposes the following conditions. Image files or folders which do not conform to these conditions cannot be recognised by the projector.
66-E NGLISH T rademark ac kno wledgements B The SD logo is a trademark. B VGA and XGA are trademarks of International Business Machines Corporation. B Macintosh is a registered trademark of Apple Computer, Inc. B S-VGA is a registered trademark of the Video Electronics Standards Association.
デバイスPanasonic PT-AE200Uの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic PT-AE200Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic PT-AE200Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic PT-AE200Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic PT-AE200Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic PT-AE200Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic PT-AE200Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic PT-AE200Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic PT-AE200Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
