PanasonicメーカーWV-CP500の使用説明書/サービス説明書
ページ先へ移動 of 35
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual. Operating Instructions Color CCTV Camera Model No. WV -CP500 WV -CP504 This illustration repr esents WV -CP500.
2 Preface About the user manuals The operating instructions of the camera consist of 2 sets: these operating instructions (PDF) and Installation Guide. This document explains how to configure the settings of the camera. Refer to the installation guide for further infor mation about how to install the camera.
3 Contents Preface ............................................................................... 2 About the user manuals ................................................. 2 T rademarks and registered trademarks ......................... 2 About the setup menus.
4 About the setup menus Perfor ming each setting item in the setup menu should be completed in advance to use this unit. Perfor m the settings for each item in accordance with the conditions of the camera shooting ar ea. The following is an example of setup procedur e when LANGUAGE is set to ENGLISH.
5 Basic operation The description below explains how to operate the setup menu basically . The operations in the setup menu are per formed with the operation buttons after calling up the setup menu on the connected video monitor . Refer to the installation guide for fur ther information about the operation buttons.
6 Screen transition diagram MODEL WV-CP500 SERIES CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP ENABLE **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF WHIT.
7 Camera title setting [CAMERA ID] This item specifies the camera title. The camera title that indicates the camera location and other information about the camera is created with alphanumerics and symbols, and is displayed on the scr een. The camera title is named with up to 16 characters.
8 Camera operation setting [CAMERA SETUP] The following describes the camera operation settings. The following settings can be configured on the "CAMERA SETUP" screen displayed fr om the top screen. Refer to page 5 for how to call up the screen.
9 Step 5 Move the cursor to "SCENE1" and press the right or left button to select "SCENE1" to r esume normal operation. Important: • When "SCENE2" is se.
10 Step 2 Move the cursor to "SUPER-D5" and select the item from the following: ON (default): Activates the SUPER-D5 function all the time. ( + See below) ON (i-VMD): Activates the SUPER-D5 function all the time. ( + See below) In addition to the SUPER-D5 function, the motion detection function also works.
11 When not using the SUPER-D5 function Followtheprocedur ebelow . Step 1 WhentheSUPER-D5functionissetto"OFF",brightareasofanimagear emaskedtofacilitatethevisibilityofdarkareas.
12 When the SUPER-D5 function is set to "OFF": OFF (1/60) (default), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, and 1/10 000 When the SUPER-D5 function is set to "ON" or ".
13 Note: If the situation meets one of the following or other , color may not be accurately reproduced. • Thesubjectismostlyhighly-colored. • Thephotographicatmosphereisunderthebrightblueskyoratnightfall.
14 Manual fine adjustment of white balance The white balance is manually fine adjusted after white balance automatically adjustment in the automatic color temperature tracking mode (A TW1, A TW2) or automatic white balance control mode (A WC). Follow the procedur e below .
15 Step 1 Move the cursor to "BW MODE" and select the black-and-white control fr om the following: AUTO1 (default): Automatically toggles between color and black-and-white images in accordance with the scr een brightness (illuminance). The black-and-white mode is selected for dark images, and the color mode is selected for bright images.
16 9. i-VMD setting [i-VMD] The intelligent motion detection function allows the camera to detect motion and appearance/disappearance of an object or scene change with the camera.
17 Detect motion of objects Move the cursor to "MOTION" and select from the following. ON: Provides an alarm signal when motion is detected. OFF (default): Does not detect motion.
18 Perform the settings relating to the detection of appearance/disappearance of stationary objects Perfor m the settings relating to the detection of appearance/disappearance of stationary objects as follows. Up to 4 appearanc- es/disappearances of stationary objects can be simultaneously detected.
19 Set the detection areas Set the detection areas for motion detection and the detection of appearance/disappearance of stationary objects. Up to 2 detection areas can be set. Follow the procedur e below . Step 1 Move the cursor to "AREA" and select "SETUP", and then press the setting button.
20 Setting of scene change detection This function detects a change in the subject state that occurs by covering the camera with a cloth, a cap, or others, or by changing the camera direction largely . Follow the procedur e below . Step 1 Move the cursor to "i-VMD" and press the setting button.
21 Configure alarm notification Follow the procedur e below . Step 1 Move the cursor to "i-VMD" and press the setting button. → The "i-VMD SETUP" screen appears. Step 2 Move the cursor to "ALARM" and configure alarm notification.
22 Camera system setting [SYSTEM SETUP] Perfor ms the settings relating to the camera system such as synchr onization, alarm input/output ter minal, and privacy zone. The following settings can be configured on the "SYSTEM SETUP" screen displayed fr om the top screen.
23 Step 1 Set "SYNC" to "LL" and press the setting button. → The "SYNC" screen appears. Step 2 Connect the video output signal and external synchronizing input signal of the camera to a 2-input oscilloscope, and move the cursor to "COARSE".
24 Configure the settings relating to the alarm output terminal Select the alarm output operation. Follow the procedure below . Step 1 Move the cursor to "ALARM IN/OUT" and press the setting button. → The "ALARM IN/OUT" screen appears.
25 Step 2 Move the cursor to the number at the right of the title and select the zone number using the right or left button. Step 3 Move the cursor to "POSITION" and press the setting button. Step 4 Use the up, down, right, and left buttons to determine the left upper position of the zone to be set and press the setting button.
26 14. Electronic zoom setting [EL-ZOOM] Select "On" or "Off" to determine whether or not to use the electronic zoom. When "ON" is selected, the zoom factor and the panning/tilting settings can be configured. ON: Uses the electronic zoom.
27 Back focus setting [BACK-FOCUS SETUP] Selects the back focus setting type and perfor ms fine adjustment. The following setting can be configured on the "BACK- FOCUS SETUP" screen displayed fr om the top screen. Refer to page 5 for how to call up the scr een.
28 Step 3 Move the cursor to "C/L ← → B/W" and select the back focus adjustment type from the following: AUTO (default): Adjusts the back focus function automatically and corrects out of focus when switching between color and black-and-white images.
29 Special menu setting [SPECIAL SETUP] The special menu setup is per formed including the setting of the camera image quality and the communication configuration when a receiver is used. The following settings are to be configured on the "SPECIAL SETUP" screen displayed from the top screen.
30 Flaw compensation [PIX OFF] Flaws in the displayed camera image are corr ected. Up to 16 points can be corrected. Follow the procedur e below . Step 1 Move the cursor to "PIX OFF" and press the setting button. → The "PIX OFF" screen appears.
31 Communication setting [COMMUNICATION] The requir ed communication configuration is perfor med to use this unit integrated into the system with a receiver . COAX (RCV): Select COAX (RCV) when using our receiver (e.g. WV -RC100 or WV -RC150). COAX (default): Does not use any receiver .
32 Language selection [LANGUAGE SETUP] A language for the setup menu is selected from the following: The language selection can be made on the "LANGUAGE SETUP" screen displayed fr om the top screen. Refer to page 5 for how to call up the scr een.
33 Shortcut operation Use of a system controller with the "camera function" button allows users to perfor m the shor tcut settings with use of the numeric keypad and camera function button.
34 System controller operation Setting contents [2]+[1]+[1]+[Camerafunction] Scene change ON [2]+[1]+[2]+[Camerafunction] Scene change OFF [2]+[1]+.
Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America www .panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic W ay 2H-2, Secaucus, New Jersey 07094 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www .
デバイスPanasonic WV-CP500の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Panasonic WV-CP500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic WV-CP500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic WV-CP500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic WV-CP500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic WV-CP500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic WV-CP500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic WV-CP500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic WV-CP500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
