ParaBodyメーカー220の使用説明書/サービス説明書
ページ先へ移動 of 24
1 220 GYM SYSTEM CLASS H PAR T # 7017301 REV . G Revision: 09/13/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 220 Gym System. Please read these instructions thoroughly and keep them for future reference.
Minimum Required Usable S p ace Length = 82 inches (208.5 cm) 6’ 10” Width = 71 inches (180.5 cm) 5’1 1” Height = 83 inches (21 1 cm) 6’ 1 1” 1 Square = 1’ X 1’ 4 Length = 82 inches (208.
5 P AR TS LIST 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 PA R T # 7005008 7005708 6994608 7005308 7005208 7005408 7005508 6999708 7005108 7005808 7005608 6940808 6994721 6549301 6194601 6523401 7006202 701.
FIGURE 1 6 STEP 1: • LOOSEL Y assemble the FOOTPLA TE (62) to the lower holes in the FRAME (1) using one 3/8 x 3” BOL T (29) and one 3/8 LOCKNUT (34) 1 34 30 2 62 3/8 X 3-3/4 29 41 34 3 • LOOSEL Y assemble two BASE PLA TES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOL TS (30) and four 3/8” LOCK NUTS (34).
7 FIGURE 3 STEP 3: FIGURE 2 • Insert two WEIGHT PLA TE BUSHINGS (23) into each of the fifteen WEIGHT PLA TES (22) as shown in FIGURE 2. STEP 2: • Slide the WEIGHT PLA TE SHAFT (18) thru the hole in the HEAD PLA TE (19), and lock in place using one E-RING (60) as shown in FIGURE 3.
• Insert two GUIDE RODS (16) into the BASE (2) as shown on FIGURE 4. (NOTE: If the 220 SHROUD OPTION was purchased, place the GUIDE RODS (16) through the BOTTOM SHROUD BRACKET (FOUND IN THE SHROUD KIT BOX ) into the BASE (2), as shown in FIGURE 4.
9 STEP 7: 22 22 • Using hammer tap one 5/16 X 2” ROLL PIN (47) thru LEFT PRESS HANDLE (7) until it is flush with other side of HANDLE as shown in FIGURE 6 8 6 40 7 FIGURE 6 STEP 6: • Place LEFT PRESS HANDLE (7) onto PRESS ARM (8).
FIGURE 8 8 49 29 36 9 34 STEP 8: • Place PRESS ARM (8) into PRIMAR Y PIVOT (9) and securely tighten using two 3/8 X 3” BOL TS (29), four 3/8” FLA T W ASHERS (36) two 3/8” LOCK NUTS (34) • Insert and tighten two 3/8” LOCKING SPRING PINS (49) into PRESS HANDLES (6), (7).
FIGURE 9 11 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9 • Assemble the PRIMAR Y PIVOT (9) of the PRESS ARM ASSEMBL Y to the top of the FRAME (1) using 1/2 X 8” BOL T (33), two 1/2” FLA T W ASHERS (37) and 1/2” LOW HT LOCK NUT (35).
12 STEP 10: • Securely tighten the SPRING PIN (50) to the FRAME (1) and hand tighten the THREE PRONG KNOB (52) • Apply four P ARAGLIDES (58) to the INSIDE of the tube of FRAME (1) as shown.
FIGURE 1 1 STEP 1 1: • Insert two 1/2” FLANGE BEARINGS (40) into LEG PEDEST AL (1 1) as shown. • Assemble the LEG PEDEST AL (1 1) to the FRAME (1) using one 1/2 X 4” BOL T (32), two RH W ASHER.
ILLUSTRA TION A NOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER T O THE CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEG PRESS KIT 14 • ILLUSTRA TION “A” used as cable routing reference for ste.
15 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Refer to cable ILLUSTRA TION “A” on page 1 1 for cable routing while installing pulleys. STEP 13: FIGURE 13 • Assemble one 3-1/2” PULLEY (24) into P.
16 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 14 • Refer to cable ILLUSTRA TION “A” on page 1 1 for cable r outing while installing pulleys. STEP 14: • Assemble one 3-1/2” PULLEY (24) to th.
17 STEP 15 • Screw end of LA T CABLE (20) into top of PLA TE SHAFT (18) and securely tighten JAM NUT as shown in FIGURE 15 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 15 20 • Slip ring of WEIGHT S.
18 • Refer to cable ILLUSTRA TION “A” on page 1 1 for cable r outing while installing pulleys. STEP 16: • [CABLE MUST BE POSITIONED BETWEEN PULLEY AND LOWER BOL T ASSEMBL Y ON LEG PEDEST AL (1.
• Refer to cable ILLUSTRA TION “A” on page 1 1 for cable r outing while installing pulleys. STEP 17: • Secure end of LOW CABLE (21) using one 3/8 x 3-3/4 BOL T (30), one 3/8” FLA T W ASHER (.
20 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Attach two 4 X 7” ROLLER P ADS (15) to the LEG PEDEST AL (1 1) using one 3/4 X 17” TUBE (14) and two 3/4” ST ARLOCK COLLARS (54) as shown in FIGURE 18.
FIGURE 19 26 17 25 21 57 ADJUSTMENT ADJUSTMENT PULL AND TWIST TO DISENGAGE • If upon completion of assembly , the HEAD PLA TE (19) does not sit on top of the first WEIGHT PLA TE (22), push the HEAD PLA TE (19) down, insert the WEIGHT SELECTOR PIN (51) and perform several repetitions at the press station.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 22 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
23 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
デバイスParaBody 220の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ParaBody 220をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParaBody 220の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ParaBody 220の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ParaBody 220で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ParaBody 220を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParaBody 220の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ParaBody 220に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParaBody 220デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。