ParaBodyメーカー835102の使用説明書/サービス説明書
ページ先へ移動 of 19
Serious Steel 835102 HIP SLED ASSEMBLY INSTRUCTIONS I I I Part # 6754601 1 Revision: 5/24/00.
I IMPORTANT NOT ,ES I WELCOME TO THE WORLD OF ~l~iOU$ ~t~t~. ~ Please note: * Thank you for purchasing the Parabody 835102 HIP SLED. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
KEY 1 2 4 5 6 7 8 9 10 11 14 15. 16 17 18 19 2O 21 22 23 24 PART # DES CRIPTION 6504903 ~3ASE 6506803’ ~ PLATFORM SLEEVE 6507403 PAD SUPPORT 6507703 RIGHT HANI~L~ ’ 6507803 LEFT HANDLE 6505403 REAR UPRIGI2IT .
FIGURE 1 X 3-1/4" STEP 1: ¯ Insert two 2" SQ. END CAPS (26) into each end of the BASE (1) as shown in FIGURE ¯ Attach two 2" SQ, COVER CAPS (28) over each end ofthebase of the REAR UPRIGHT (6). ¯ SECURELY assemble the PEAK UPP,_IGHT (6) to the BASE (1) as shown in FIGURE 1 using two 1/2 X 3-1/4" BOLTS (41.
~1/2 X 5" _LLL _LLLL LLLLLLLLLLLLLL _LLLLLLLLLLLLLLLLL .LLLLLLLLLLLLLLLLLLLLLLLL LLLLLLLLLLLLLLLLLLLLL LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL .LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL[ LLLLLLLLLLLLLLLL.
_LLLL _LLLL .LLLLI 1/2 X 4"~ FIGURE 4 STEP 4: ¯ Assemble the PLATFORM SLEEVE (2) to the BASE (1) as shown in FIGURE 4 using one 1/2 X 4" BOLT (42), and one LOCKNUT (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY, YET ALLOWING THE PLAT- FORM SLEEVE TO ROTATE FREELY) ¯ Pull back the 1/2" DIA.
’@1/2 X 4-1/2" ) I I I I I I I I / I I ! ! / / / / FIGURE 5 3/8 X 4-1/2"@ ~ STEP 5: ¯ LOOSELY assemble the LEFT (8) and RIGHT RAILS (9), along with the SEAT PAD (18) to the BASE (1) as shown in using two 3/8 X 4-1/2" BOLTS (38), two 3/8" LOCK WASteRS (30), and two 3/8" WASHERS (29).
1/2 X 4-1/2 ~ FIGURE 6 STEP 6: ¯ Insert four 2" SQ. END CAPS (26) into the each end of the CARRIAGE (16) as shown in FIGURE ¯ SECURELY assemble four 3" DIA. WHEELS (20) to the sides of the CARRIAGE (16) as shown in FIGURE 6 using 4-1/2" BOLTS (43), eight 1/2" WASHERS (32), and four 1/2" LOW HEIGHT LOCK NUTS (34).
LOW HEIGHT 1/2 X 2-3/4"~ [GURE 7 ~3/8 X 2" STEP 7: ¯ SECURELY assemble two 2" DIA. WHEELS (21) to the BRACKETS onthe left side of the CARRIAGE (16) as shown FIGURE 7 using two 3/8 X 2" BOLTS (36), four 3/8" WASHERS (29), and two 3/8" LOCK NUTS (31).
Q1/2X4-1/2" SAFTEY STOP FIGURE 8 STEP 8: ¯ Remove the two temporary. 1/2 X 4-1/2" BOLTS (43) from STEP ¯ Swing the LEFT (8) and RIGHT (9) RAILS out enough to insert the CARRIAGE AS SEIV~LY (16) in between CARRIAGE (16) to rest on the SAFETY STOPS underneath the RAILS.
Q1/2 X 4-1/2" REVERSE VIEW FOR ASSEMBLY FIGURE 9 ;TEP 9: ¯ SECURELY reassemble the LEFT (8) and RIGHT (9) RAILS to the REAR UPRIGHT (6) as shown in FIGURE 9 using the two X 4-1/2" BOLTS (43), four 1/2" WASHERS (32), and two 1/2" LOCK NUTS (33).
X 4-1/2" FIGURE 10 STEP 10: ¯ SECURELY assemble the WEIGHT SUPPORT (13) to the CARRIAGE (16) as shown in FIGURE 10 using two 1/2 X 4-1/2" BOLTS (43), two 1/2 X 3-1/4" BOLTS (41), eight.
1/2 X 3-1/4" FIGURE 11 STEP 11: ¯ Insert two 2" SQ. END CAPS (26) into the ends of each PAD SUPPORT (3) as shown in FIGURE ¯ SECURELY assemble the two PAD SUPPORTS (3) to the CARRIAGE (16) as shown in FIGURE 11 using two 1/2 X 3-1/4" BOLTS (41), four 1/2" WASHERS (32), and two 1/2" LOCKNUTS (33).
LL LLL LLLLL _LLLL __LLLL __LLLL __LLLL __LLLL __LLLL ~L_LLL __LLL __LLL _LLLL _LLLL FIGURE 12 L LLLL LLLL LLLL LLLL LLLL LLLL LLLL LLLL LLLL LLLL LLLL LLL ~L L L LLL LLLL _LLLLL _LLLLL _LLLLL_ _LLLLL.
FIGURE 13 STEP 13: ¯ Assemble the FOOT PLATE (10) to the CAR~AGE (16) as shown in FIGURE 13, using two 1/2 X 1-1/4" BOLTS (39), two WASHERS (32), and two 1/2" LOW HEIGHT LOCK NUTS (34).
S BUSHING FIGURE 14 STEP 14: ¯ To assemble the CARRIAGE STOP BAR (7) to theside of the LEFT RAIL (8), start by inserting the top of the BAR (7) imo BUSHING at the top of the RAIL as far as possible, then lower the BAR (7) into the SURE-LOC BUSHING at the bottom ol.
3/8 X 1"~ FIGURE 15 STEP 15: ¯ SECURELY assemble the PAD STOP (15) to the BACK PAD (19) as shown in FIGURE 15 using t~vo 3/8 X 1" BOLTS (35)... 3/8" LOCK WASHERS (30), and two 3/8" WASHERS (29). MAKE SURE ALL CONNECTIONS ARE SECURELY TIGHTENED.
CARRIAGE STOPS SURE-LOC~ BUSHING "" 35°~40°,45 ° FIGURE 16 STEP 16: ¯ The PLATFORM (11) can adjust into three positions: 35, 40, and 45 degrees ¯ The HIP SLED was designed ~vith the SURE-LOC SYSTEM for ultimate safety.
HANLDE FIGURE 17 STEP 17: ¯ To perform LEG PRESSES, center the BACK PAD (19) down on top of the PLATFORM (11) and lock the PAD STOP (15) back of the BACK PAD (19) behind the PLATFORM HANDLE then rota.
デバイスParaBody 835102の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ParaBody 835102をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParaBody 835102の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ParaBody 835102の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ParaBody 835102で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ParaBody 835102を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParaBody 835102の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ParaBody 835102に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParaBody 835102デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。