ParaBodyメーカー848の使用説明書/サービス説明書
ページ先へ移動 of 18
1 848 LA T OPTION CLASS H PAR T # 7080301 REV . B Revision: 07/10/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 848 LA T OPTION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
4 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 P AR TS LIST PA R T # 6826608 6826908 6825408 6827208 6825502 6275302 6274402 6542402 6824801 3103102 31 16201 6177001 6405201 6467001 6692601 6825101 KEY 1 2 3 .
FIGURE 1 STEP 1: • SECUREL Y assemble the one 3/8 X 2-3/4” BOL T (25), two 3/8” W ASHERS (19), and one 3/8” LOCK NUT (20) to the ST AND (3) as shown in FIGURE 1. • Assemble two 2” SQ. COVER CAPS (14) onto the ends of the ST AND (3) as shown in FIGURE 1.
6 FIGURE 4 STEP 3: • Assemble one 17-1/2” FOAM STRIP (16) to the underside of the CROSS BRACE (4) as shown in FIGURE 3. • Assemble two 2-1/2 X 5-1/2” NON-SKID STRIPS (12) to the CROSS BRACE (4) as shown in FIGURE 3. FIGURE 3 STEP 4: • SECUREL Y attach one 1-1/4” SQ.
7 STEP 5: FIGURE 5 • Slide the CARRIAGE (5) over the UPRIGHT (2) as shown in FIGURE 5. • Assemble the ST AND (3) to the UPRIGHT (2) as shown in FIGURE 5.
STEP 6: FIGURE 6 • SECUREL Y assemble the BASE (1) to the UPRIGHT (2) using one 1/2 X 3” BOL T (27), two 1/2” W ASHERS (21) (slide front washer INSIDE of tube) , and one 1/2” LOCK NUT (22). See FIGURE 6. • Insert one 3 X 2” END CAP (15) and one 2” SQ.
9 STEP 7: FIGURE 7 • Route the CABLE (9) through the UPRIGHT (2) as shown in FIGURE 7. • SECUREL Y assemble three 3-1/2” PULLEYS (1 1) into the slots of the UPRIGHT (2) using three 3/8 X 2-3/4” BOL TS (25), six 3/8” FLANGE SP ACERS (31), and three 3/8” LOCK NUTS (20) as shown in FIGURE 7.
10 STEP 8: FIGURE 8 23 3/8 X 2” 19 19 20 9 8 29 2 5 • Place one 3-1/2” PULLEY (11) into the loop of the CABLE (9) below the second and third PULLEY of the UPRIGHT (2) as shown in FIGURE 8.
11 STEP 9: FIGURE 9 23 3/8 X 2” 19 19 20 9 11 2 • Route the end of the second CABLE (9) through the slot on the UPRIGHT (2) then SECUREL Y assemble one 3-1/2” PULLEY (1 1) to the UPRIGHT (2) using two 3/8 X 2-1/2” BOL TS (24), two 3/8 X 3/8” SP ACERS (30), four 3/8” W ASHERS (19), and two 3/8” LOCK NUTS (20).
12 STEP 10: FIGURE 10 • SECUREL Y assemble the CABLE (9) to the BASE (1) using one 3/8 X 4-1/2” BOL T (26), one 3/8 X 1” SP ACER (32), and one 3/8” LOCK NUT (20) as shown in FIGURE 10.
13 STEP 1 1: FIGURE 1 1 • Attach the LA T BAR (6) to the ball end of the upper CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11. • Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11.
STEP 12: FIGURE 12 • Tilt the 848101 back and remove the ST AND (3) as shown in FIGURE 12. • T o use the 848101 LA T OPTION: (NOTE: LA T OPTION MUST BE USED WITH A BENCH. LA T OPTION CANNOT BE USED WHILE ST AND IS A TT ACHED. ST AND MUST BE A TT ACHED WITH THE FEET OUT AS SHOWN.
Thank you for pur chasing the Parabody 848 LA T OPTION. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. BENCH 2 STEP 13: FIGURE 13 • Insert the UPRIGHT (2) of the 848 into the bench as shown in FIGURE 13.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 16 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
17 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED W ARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES LifeFitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 LifeFitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 LifeFitness (UK) Ltd.
デバイスParaBody 848の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ParaBody 848をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParaBody 848の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ParaBody 848の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ParaBody 848で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ParaBody 848を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParaBody 848の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ParaBody 848に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParaBody 848デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
