Paradyneメーカー6310 MVLTの使用説明書/サービス説明書
ページ先へ移動 of 20
1 Hotwire r 6310 MVL t Modem Customer Premises Installation Instructions Document Number 6310-A2-GN10-40 February 2000 Contents Hotwire 6310 MVL Modem Overview 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before Y ou Begin 3 . . .
2 Hotwire MVL System Copper pairs run from the central office (CO) to the customer premises (CP) to create the local loop. The local loop terminates on the customer premises at the demarcation point.
3 NOTES: In this document: — A telephone is used to represent any equipment that plugs into a phone jack and uses the POTS line, such as a phone, modem, or fax machine. — End-user system is used to represent any PC with an Ethernet connection and MVL-based service.
4 Product-Related Documents T o install a phone filter , refer to the appropriate document: Document Number Document Title 6035-A2-GN1 1 Hotwire 6035 MVL Phone Filter Installation Instructions 6040-A2.
5 3. Connect a telephone (optional); go to Step 4 if you are not connecting a telephone to the MVL modem. The 6035 phone filter has a cable attached. Plug the other end of this cable into the MVL modem jack labeled PHONE. Using the existing telephone interface cable that was unplugged in Step 1, plug into the POTS filter jack labeled PHONE.
6 H Use an Ethernet crossover cable and connect the other end to a PC with an Ethernet Network Interface Card (NIC) installed. PHONE POWER ETHERNET LINE MVL Modem 98-15907 Ethernet Line PC with Ethernet Network Interface Card Ethernet Cable For MVL modem cable pin assignments, refer to Cables & Connectors on page 10.
7 The MVL modem hardware installation is now complete. When the power cord is installed, the MVL modem goes through a power-on self-test. Power -On When power is applied, the MVL modem performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on for one second.
8 Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successful self-test, the LEDs should appear as indicated in BOLD in the Condition column below . LED State Status PWR ON MVL modem has power . ALM OFF ON No active alarms.
9 LED Symptom Action LINE LED is off. V erify that the MVL LINE cable is securely installed on both ends. If the problem continues, contact the Service Provider . V erify that the line has dial tone. If there is no dial tone, contact the Service Provider .
98-15304a 6-Pin RJ11 Plugs Pin #1 Pin #6 10 T o enable the sharing of resources and review security considerations, see Microsoft ’ s Web site at www .microsoft.com . In this example of HomeLink, the PC in the family room could use the office printer .
98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 11 H The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — T o connect the MVL modem to an Ethernet hub, use the straight-through connection.
12 Optional MVL Modem W all Placement The Hotwire 6310 MVL Modem is designed for tabletop placement. The MVL modem can also be mounted on a wall. T o mount the modem, you will need: - Three slotted-he.
13 MVL Modem Hardware T emplate F ront (LEDs) 98-16171 5.43" 7.55" T o Bottom Hole.
14 Hotwire 6310 MVL Modem T echnical Specifications Item Specification * Height x Width x Depth 1.43 ″ x 6.00 ″ x 8.75 ″ (3.64 cm x 15.24 cm x 22.
15 ! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
16 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: H Directive 73/23/EEC – Council Directive .
17 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission ’ s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 6310-A2-200 This device complies with Part 15 of the FCC Rules.
18 United States – Notice to Users of the T elephone Network 1. This equipment complies with Part 68 of the FCC rules. On the equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment.
19 Notice to Users of the Canadian T elephone Network The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate T erminal Equipment T echnical Requirements document(s).
20 W arranty , Sales, Service, and T raining Information Contact your local sales representative, service representative, or distributor directly for any help needed.
デバイスParadyne 6310 MVLTの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Paradyne 6310 MVLTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはParadyne 6310 MVLTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Paradyne 6310 MVLTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Paradyne 6310 MVLTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Paradyne 6310 MVLTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はParadyne 6310 MVLTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Paradyne 6310 MVLTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちParadyne 6310 MVLTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。