Patton electronicメーカー1052の使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL MODEL 1052 iDSL Modem with RS-232 Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P a r t# 07M1052- B Doc# 058061 U B Revised 5/24/02 An ISO-9001 Certified Company.
2 T ABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice .........................
3 A.10 Temperature Range .................................................................... 17 A.11 Altitude ........................................................................................ 17 A.12 Humidity ..................................
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 1052 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment.
5 1.3 SERVICE All warranty and non-w arranty repairs m ust be returned freight prepaid and insured to P atton Electronics. All retur ns must hav e a Return Materi- als A uthorization number on the outside of the shipping container .
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor.
7 3.0 CONFIGURATION The Model 1052 is equipped with 16 DIP s witches that enable configur a- tion of the unit f or a wide variety of applications. This section describes s witch locations and e xplains the diff erent config-urations 3.
8 Figure 2. Opening the Model 1052 case Figure 1 on page 7 shows the orientation of the DIP switches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data r ate, asynchronous or synchronous data f ormat, transmit clock source .
9 Each setting represents one synchronous data rate and one asynchro- nous data rate. Note If the S2-1 switch is positioned in the OFF position, the 128 kbps sync data rate/0–38.4 kbps async data rate option is selected. Switch S1-3. Must be set to the On position (Reser v ed).
10 Switch S1-8. Must be set to the Off position (Reser v ed). Configuring DIP switch S2 Use the eight DIP s witches in S2 to enable 19.2 kbps synchronous oper- ation and set the loopback modes . The f ollowing tab le summarizes def ault positions of DIP s witches S2-1 through S2-8.
11 Switch S2-2: Must be set to the ON position (Reserved). Switches S2-3. Must be set to the Off position (Reser v ed). Switches S2-4 and S2-5: Not Assigned.
12 4.0 INSTALLATION Once the Model 1052 has been configured, it is ready to connect to the twisted pair interf ace, to the serial por t, and to the power source . This section tells you ho w to make these connections . Figure 3. Model 1052 Rear P anel 4.
13 tive and is wired f or a two-wire interface . The signal/pin relationships are shown in Figure 4. Figure 4. Model 1052 twisted pair line interface 4.2 CONNECTING THE CONNECTING THE MODEL 1052/A (RS-232) The Model 1052/A suppor ts RS-232 serial por t connections.
14 Universal A C Po wer (100–240 V AC) The Model 1052 uses a 5VDC , 2A universal input 100-240V AC , power supply (center pin is +5V). The univ ersal input power supply has a male IEC-320 power entry connector . This po wer supply connects to the Model 1052 by means of a barrel jac k on the rear panel.
15 5.0 OPERATION Once the Model 1052 is properly configured and installed, it should oper- ate transparently . This sections describes power-up , reading the LED status monitors, and using the b uilt-in loopback test modes . 5.1 POWER-UP Bef ore applying power to the Model 1052, read section 4.
16 APPENDIX A MODEL 1052 SPECIFICA TIONS A.1 T RANSMISSION FORMAT Synchronous or asynchronous A.2 T RANSMISSION LINE Single unconditioned twisted pair A.3 CONTROL SIGNALS CD and R TS A.4 CLOCKING Internal, external, or receive loopback A.5 DISTANCE Distance, max, all data rates: • 10.
17 A.10 T EMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 WEIGHT 2.
18 APPENDIX B MODELS 1052/A F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Model # Description 1052/A RS232 iDSL Modem 12V -PSM 12 VDC Po wer Supply Module 24V -PSM 24 VDC Po wer Supply Module 48V -PSM 48 VDC Po wer Supply Module 08055DCUI 100-240V A C (+5V ±5% reg.
19 APPENDIX C MODEL 1052/A INTERF ACE PIN ASSIGNMENTS RS-232 INTERF A CE (DB-25 Female Connector) (DCE Orientation) Pin # Signal 1 Shield GND 2 TD (T ransmit Data) (DTE Source) 3 RD (Receiv e Data) (D.
20 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________.
デバイスPatton electronic 1052の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 1052をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 1052の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 1052の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 1052で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 1052を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 1052の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 1052に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 1052デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。