Patton electronicメーカー1053の使用説明書/サービス説明書
ページ先へ移動 of 20
USER MANUAL MODEL 1053 iDSL Modem with RS-232 Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M1053-UG Doc# 05815U2-001 Rev .
2 TABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice ..........................
3 B Model 1053/A Factory Replacement Parts and Accessories ............................................................. 17 C Model 1053/A Interface Pin Assignments .
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 1053 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment.
5 1.3 SERVICE All warranty and non-w arranty repairs must be returned freight prepaid and insured to P atton Electronics. All returns must hav e a Retur n Mater i- als A uthor ization number on the outside of the shipping container .
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear parts and labor .
7 3.0 CONFIGURATION The Model 1053 is equipped with 16 DIP s witches that enable configura- tion of the unit f or a wide variety of applications. This section describes s witch locations and explains the diff erent configurations 3.
8 Figure 2. Opening the Model 1053 case Figure 1 on page 7 shows the orientation of the DIP switches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data rate, asynchronous or synchronous data f ormat, transmit clock source .
9 Each setting represents one synchronous data rate and one asynchro- nous data rate. Note If the S2-1 switch is positioned in the OFF position, the 128 kbps sync data rate/0–38.4 kbps async data rate option is selected. Switch S1-3: Must be set to the ON position (Reser ved) .
10 Switch S1-8: Must be set to the OFF position (Reser ved). Configuring DIP switch S2 DIP s witches in S2 are reser ved and must be set in the OFF position. The f ollowing table summarizes def ault positions of DIP switches S2-1 through S2-8. Important A pair of Model 1053s communicate synchronously across the twisted pair line connection.
11 4.0 INSTALLATION Once the Model 1053 has been configured, it is ready to connect to the twisted pair interf ace, the serial por t, and the power source .
12 tive and is wired f or a two-wire interf ace. The signal/pin relationships are shown in Figure 4. Figure 4. Model 1053 twisted pair line interface 4.2 CONNECTING THE MODEL 1053/A (RS-232) The Model 1053/A suppor ts RS-232 serial por t connections. This section describes how to connect the serial por ts to your RS-232 equipment.
13 Universal A C P ower (100–240 V AC) The Model 1053 uses a 5VDC , 2A universal input 100–240V AC , power supply (center pin is +5V). The univ ersal input power supply has a male IEC-320 power entry connector . This power supply connects to the Model 1053 by means of a barrel jac k on the rear panel.
14 5.0 OPERATION Once the Model 1053 is properly configured and installed, it should oper- ate transparently . This sections descr ibes power-up , reading the LED status monitors. 5.1 POWER-UP Bef ore applying power to the Model 1053, read section 4.
15 APPENDIX A MODEL 1053 SPECIFICATIONS A.1 TRANSMISSION FORMAT Synchronous or asynchronous A.2 TRANSMISSION LINE Single unconditioned twisted pair A.3 CONTROL SIGNALS CD and R TS A.4 CLOCKING Internal, external, or receive recov er A.5 DISTANCE Distance, max, all data rates: • 10.
16 A.10 TEMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 WEIGHT 2.
17 APPENDIX B MODEL 1053/A F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES Model # Description 1053/A RS232 iDSL Modem 12V -PSM 12 VDC P ower Supply Module 24V -PSM 24 VDC P ower Supply Module 48V -PSM 48 VDC P ower Supply Module 08055DCUI 100–240V AC (+5V ±5% reg.
18 APPENDIX C MODEL 1053/A INTERF ACE PIN ASSIGNMENTS RS-232 INTERF A CE (DB-25 Female Connector) (DCE Orientation) Pin # Signal 1 Shield GND 2 TD (T ransmit Data) (DTE Source) 3 RD (Receiv e Data) (D.
19 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________.
20 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________.
デバイスPatton electronic 1053の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 1053をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 1053の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 1053の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 1053で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 1053を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 1053の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 1053に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 1053デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。