Patton electronicメーカー1058の使用説明書/サービス説明書
ページ先へ移動 of 28
USER MANUAL VLINK MODEM Model 1058 & 1068 SALES OFFICE (301) 975-1000 TECHNICAL SUPPO R T (301) 975-1007 P a r t# 07MVLINK R e v . A Doc# 058091U Rev.
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Radio and TV Interference ............................................................ 4 1.2 CE Notice ........................................
3 D VLINK Series Interface Pin Assignment ................................. 26 D.1 10/100Base-T Interface .............................................................. 26 RJ-45 .........................................................................
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all VLINK modem components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment.
5 1.3 FCC PART 68 (DV V ERSION ONLY) This equipment complies with P art 68 of the FCC Rules. Please note the f ollowing: This equipment complies with P ar t 68 of FCC rules and the requirements adopted by A CT A.
6 If this equipment causes harm to the telephone networ k, the telephone company will notify y ou in adv ance that temporar y discontinuance of ser- vice ma y be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possib le.
7 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor. If any questions or prob lems arise dur ing installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007.
8 transparently (unmodified) through the VLINK modems. The VLINK modems automatically add and delete MA C addresses , only passing pack ets across the VDSL link that are meant for the remote peered LAN.
9 3.0 INSTALLATION Because the VLINK modem requires no configuration, it can be installed quickly . If you are installing a standalone unit, refer to section 3.1 “Standal- one unit installation”. Otherwise, ref er to section 3.2 “Rac k card installation”.
10 3.2 RACK CARD INSTALLATION The VLINK modem rack card comprised a front card and a rear card.Do the f ollowing to install the cards into the rac k chassis: 1. Slide the rear card into the back of the chassis along the metal r ails. 2. Secure the rear card using the supplied metal screws .
11 6. Connect the Ether net interf ace (ref er to section 3.4, “Connecting the 10/100Base-T Ethernet Interface” on page 12). 3.3 CONNECTING THE T WISTED-PAIR LINE INTERFACE The VLINK modem suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 6,000 ft (1.
12 The terminal bloc k connector on the VLINK modem's twisted pair inter- f ace is polarity insensitive and is wired f or a two-wire interf ace. The signal/pin relationships is shown in Figure 5. Figure 5. VLINK modem (terminal block v ersion) twisted pair line interface.
13 Connecting the 10/100Base-T Ethernet P ort to a Hub The VLINK modem 10/100Base-T interface is configured as DTE (Data T er minal Equipment), just like a 10/100Base-T netw ork interface card in a PC . Theref ore, it “e xpects” to connect to a 10/100Base-T Hub using a straight-through RJ-45 cab le.
14 work. The RJ-45 connector in the VLINK modem’ s POTS/ISDN interf ace is wired as shown in Figure 9. Figure 9. VLINK (RJ-45) PO TS/ISDN interface 3.6 CONNECTING POWER An e xter nal A C or DC power supply is a vailab le separately . This connec- tion is made via the barrel jack on the rear panel of the VLINK standalone modem.
15 4.0 CONFIGURATION (MODEL 1068 ONLY) The VLINK modem has eight DIP switches f or configuring the unit for a wide variety of applications. This section descr ibes s witch locations and e xplains the different configur ations.
16 Figure 11. Model 1068 standalone modem DIP switch orientation Figure 12. Model 1068 rack card DIP s witch orientation Power VLINK Modem Link QOL VLINK Link Activity Ethernet 1234 ON Push toggle to .
17 4.2 CONFIGURING DIP SWITCH S1 DIP s witch S1 is where you configure the VDSL line rate, symmetric or asymmetric, Ethernet full auto negotiation capability (100Base-T full or half duple x, 10Base-T full or half duplex) or limited auto sense (only 100Base-T half duple x, 10Base-T full or half duplex).
18 T able 3: Asymmetric VDSL Line Rates Selection Chart S1-2 S1-3 S1-4 Asymmetric Line Rates DS/US OFF OFF ON 4.17 Mbps/1.56 Mbps (Mode 0) OFF ON ON 9.
19 5.0 OPERATION Once the VLINK modems are proper ly installed, they should oper ate transparently . No user settings required. This section describes reading the LED status monitors. 5.1 POWER UP Bef ore applying power to the VLINK modem, please revie w section 3.
20 T able 5: F ront panel LED description for standalone modem LED Description Po w e r On (green) when power is applied to the unit. Off when no power is applied to the unit. VLINK - Link On (green) when the end-to-end VDSL link between the units is established.
21 Figure 14. VLINK modem rack card front panel T able 6: F ront panel LED description for rack card modem LED Description P ower Solid GREEN to indicate the unit is powered on. VLINK modem Link (Active Green) Solid g reen (ON) to indicate that the end-to-end VDSL link betw een the VLINK modems is established.
22 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T , IEEE 802.3 Ether net • VDSL Connection: RJ-45 and T erminal Block A.2 T RANSMISSION LINE T wo-wire unconditioned twisted pair. A.3 VDSL LINE RATE Model 1068 —16.67 Mbps, symmetric upstream/downstream.
23 A.8 T EMPERATURE RANGE 32–122°F (0–50°C) A.9 HUMIDITY Up to 90% non-condensing. A.10 DIMENSIONS 1.58H x 4.16W x 3.75D in. (10.6H x 4.1W x 8.8D cm).
24 APPENDIX B MODEL 1058 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 1058DRC/CO CO VDSL Rack C.
25 APPENDIX C MODEL 1068 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 1068DRC/CO CO V ariable R.
26 APPENDIX D VLINK SERIES INTERFACE PIN ASSIGNMENT D.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection D.2 VDSL INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection T erminal Block See Figure 5 on page 12.
27 APPENDIX E DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note Model 1058 is fixed at 12.5 Mbps , 4,000 ft (1,220 m). Symm Line Rate (DS/US) Distance in feet (km) 6.25 Mbps 4,500 (1.37) 9.38 Mbps 4,150 (1.26) 12.5 Mbps 4,000 (1.22) 16.67 Mbps 3,300 (1.
28 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________.
デバイスPatton electronic 1058の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 1058をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 1058の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 1058の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 1058で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 1058を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 1058の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 1058に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 1058デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。