Patton electronicメーカー1060rcの使用説明書/サービス説明書
ページ先へ移動 of 28
USER MANUAL MODEL 1060RC AC Powered, Asynchronous Short Range Modem: Rack Mount Card SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1060RC components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1060RC components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
3.0 CONFIGURA TION This section describes the location and orientation of the Model 1060RC's configuration switches and provides detailed instructions on setting each of the switches. 3.1 FRONT CARD CONFIGURA TION The Model 1060RC uses a set of eight DIP switches that allow configuration to a wide range of asynchronous applications.
3.0 CONFIGURA TION This section describes the location and orientation of the Model 1060RC's configuration switches and provides detailed instructions on setting each of the switches. 3.1 FRONT CARD CONFIGURA TION The Model 1060RC uses a set of eight DIP switches that allow configuration to a wide range of asynchronous applications.
Control Input (C in ): The Control Input signal is used by the local Model 1060RC as an input signal to “turn on” (in the “Enabled” settings) and allow data transmission to the remote device. This is required for half-duplex/ switched-carrier environments as well as in hardware flow control applications.
Control Input (C in ): The Control Input signal is used by the local Model 1060RC as an input signal to “turn on” (in the “Enabled” settings) and allow data transmission to the remote device. This is required for half-duplex/ switched-carrier environments as well as in hardware flow control applications.
3.4 REAR CARD CONFIGURA TION The 1060RC has four interface card options: DB-25/RJ-1 1, DB-25/RJ-45, RJ-45/RJ-1 1 and dual RJ-45. Each of these options supports one RS-232 connection and one 4-wire connection (the RS- 232 port is always the lower port on the interface card).
3.4 REAR CARD CONFIGURA TION The 1060RC has four interface card options: DB-25/RJ-1 1, DB-25/RJ-45, RJ-45/RJ-1 1 and dual RJ-45. Each of these options supports one RS-232 connection and one 4-wire connection (the RS- 232 port is always the lower port on the interface card).
The table below provides an overview of strap functions for the DB- 25/modular cards. Following this overview is a detailed description of each strap's function.
The table below provides an overview of strap functions for the DB- 25/modular cards. Following this overview is a detailed description of each strap's function.
SGND & FRGND (JB5) This strap pertains to the DTE interface, which is a 10-position modular RJ-45 jack. In the connected (closed) position, this strap links modular pin 5 (Signal Ground) and frame ground. In the open (disconnected) position, pin 5 is "lifted" from frame ground.
SGND & FRGND (JB5) This strap pertains to the DTE interface, which is a 10-position modular RJ-45 jack. In the connected (closed) position, this strap links modular pin 5 (Signal Ground) and frame ground. In the open (disconnected) position, pin 5 is "lifted" from frame ground.
Switching the Power Supply On and Off The power supply on/off switch is located on the front panel. When plugged in and switched on, a red front panel LED will glow . Since the Model 1000R16 is a "hot swappable" rack, it is not necessary for any cards to be installed before switching on the power supply .
Switching the Power Supply On and Off The power supply on/off switch is located on the front panel. When plugged in and switched on, a red front panel LED will glow . Since the Model 1000R16 is a "hot swappable" rack, it is not necessary for any cards to be installed before switching on the power supply .
RJ-45 SIGNAL PIN# COLOR COLOR PIN# SIGNAL GND 2 Orange .............Brown 7 GND RCV - 3 Black ................Green 5 XMT - XMT+ 4 Red ..................Y ellow 6 RCV+ XMT - 5 Green ...............Black 3 RCV - RCV+ 6 Y ellow ..............Red 4 XMT+ GND 7 Brown .
RJ-45 SIGNAL PIN# COLOR COLOR PIN# SIGNAL GND 2 Orange .............Brown 7 GND RCV - 3 Black ................Green 5 XMT - XMT+ 4 Red ..................Y ellow 6 RCV+ XMT - 5 Green ...............Black 3 RCV - RCV+ 6 Y ellow ..............Red 4 XMT+ GND 7 Brown .
5.2 POWER-UP There is no power switch on the Model 1060RC: Power is automatically applied to the 1060RC when its card-edge connector makes contact with the chassis' mid-plane socket, or when the chassis' power supply is turned on.
5.2 POWER-UP There is no power switch on the Model 1060RC: Power is automatically applied to the 1060RC when its card-edge connector makes contact with the chassis' mid-plane socket, or when the chassis' power supply is turned on.
APPENDIX A SPECIFICA TIONS T ransmission Format: Asynchronous External Interface: RS-232C/CCITT V .24 connection via DB-25 female; EIA/TIA-561 connection via RJ-45 (10 wire); twisted pair connection v.
APPENDIX A SPECIFICA TIONS T ransmission Format: Asynchronous External Interface: RS-232C/CCITT V .24 connection via DB-25 female; EIA/TIA-561 connection via RJ-45 (10 wire); twisted pair connection v.
APPENDIX C F ACTOR Y REPLACEMENT P ARTS The Patton Model 1060RC rack system features interchangeable rear half cards, power cords/fuses for international various operating environments and other user-replaceable parts. Model numbers and descriptions for these parts are listed below: Patton Model # Description 1000RPEM .
APPENDIX C F ACTOR Y REPLACEMENT P ARTS The Patton Model 1060RC rack system features interchangeable rear half cards, power cords/fuses for international various operating environments and other user-replaceable parts. Model numbers and descriptions for these parts are listed below: Patton Model # Description 1000RPEM .
APPENDIX E BLOCK DIAGRAM Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business. I trust that you find this user manual helpful.
.
.
.
APPENDIX E BLOCK DIAGRAM Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business. I trust that you find this user manual helpful.
デバイスPatton electronic 1060rcの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 1060rcをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 1060rcの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 1060rcの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 1060rcで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 1060rcを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 1060rcの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 1060rcに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 1060rcデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。