Patton electronicメーカー1092Aの使用説明書/サービス説明書
ページ先へ移動 of 19
USE R MAN UA L MODEL 1092 A High Speed, 2-Wire/4-Wire , Sync & Async Short Range Modem Part# 07M1092A- E Doc# 033031U D Revised 03/29/0 0 SALES OFFIC E (301)975-100 0 TECHNICAL SUPPOR T (301)975-100 7 http://ww w .
TABLE OF CONTENT S Sectio n Pag e 1. 0 Warranty Informatio n ............................................................ . 2 1. 1 Radio and TV Interferenc e 1.2. CE Notic e 1. 3 Service 2. 0 General Informatio n ......................................
1.3 SERVIC E All warranty and non-warranty repairs must be returned freigh t prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shippin g containe r . This number may be obtained from Patton Electronic s T echnical Service at : tel: (301)975-100 7 ; email: support@patton.
2.3 1092A SNMP MANAGEMENT SOLUTIONS Model 1092A is SNMP manageabl e when it is connected to a rack-mounted Model 1092ARC . SNMP management is enable d through a 1001MC rack management card located in the Patto n Electronics Rack System. 2.3.1 HTTP/HTML Managemen t The 1001MC maintains HTML pages that can be viewed through a web browse r.
7 3.1.1 Configuration DIP Switch Set “S1 ” Use the eight switches in DIP Switch Set “S1” to configure the dat a rate, asynchronous or synchronous data format, transmit clock sourc e and response to RDL request. The following table summarizes defaul t positions of DIP Switch S1.
9 Switch S1-8: Response to RD L Reques t Use Switch S1-8 to allow Model 1092A to enter the Remote Digita l Loopback diagnostic test when requested to do so by the far end Mode l 1092A For example, when Switch S1-8 is set to “ON”, it will enter RD L mode (See Section 5.
1 1 3.2 CONFIGURING THE SOFT WARE SWITCHE S The Model 1092A features a menu-driven command system tha t allows you to configure the local 1092A. Follow the instructions belo w to configure the Model 1.
1 3 MAIN MENU Option 2: Display Hardware Configuratio n Select Option 2 to display the configuration of the hardware DIP - switches. T o use the Hardware Configuration for the Activ e Configuration, select MAIN MEN U Option 5. Then select “Us e Hardware DIP-Switches”.
1 5 2. Data Forma t Select Option 2 in the SOFTWARE CONFIGUR ATIO N Menu t o select the async or sync data format (See below). 3. Clock Mod e Select Option 3 in the SOFTWARE CONFIGUR ATION Menu t o select the sync clock mode (See below) .
7. DTE Controlled Remote Digital Loo p Select Option 7 in the Menu t o enable DTE control of the Remote Digital Loop Menu (See below). Th e interface by selecting Enable (Option 1). To instruct the 1092A t o ignore this request from the DTE interface, select Disable (Option 2) .
1 9 The Model 1092A Test Modes are described on the following page. To run or terminate a particular test, key in the option to get to tha t screen menu. OF F T erminates all test s 51 1 Initiates the built-in test pattern generator and detector . 511 with Error s Initiates the built-in test pattern generator and detector.
2 1 3. Proper 2-Wir e Pairin g between the two modems is as follows : SIGNA L PIN # PIN # SIGNA L TI P 4 --------------------------------------- - 4 TI P RIN G 5 --------------------------------------- - 5 RIN G 4.
2 3 2) Hold the module with the faceplate toward you and align th e module with the guide slots in the rear panel of the Mode l 1092A. 3 ) While keeping the module’s faceplate parallel with the Mode l 1092A rear panel, slide the module straight in – so that the car d edge contacts line up with the socket inside the chassis.
2 5 4.3.2 Connecting to a DC Power Sourc e The 48 VDC power supply option uses a 3-pin terminal block wit h spring-type connectors. Please refer to the Model 1090 Series Servic e Manual . WARNING ! There are no user-serviceable parts in th e power supply section of the Model 1092A .
been placed in Test Mode. The unit can be placed in test mode by the local or remote user . N S Glow red to indicate that the local Model 1092A has not yet connected with the remote 5.3 TEST MODE S The Model 1092A offers two proprietary loopback test modes, plu s a built-in V .
5.3.3 Using the V .52 (BER) Test Pattern Generato r T o use the V .52 BER tests in conjunction with the Remote Digita l Loopback tests (or with Local Line Loopback tests), follow thes e instructions : 1. Locate the “5 11/511E” toggle switch on the front panel of the 1092A and move it U P .
APPENDIX B PA TTON ELECTRONIC S MODEL 1092A FACTORY REPLACEMEN T PART S AND ACCESSORIE S Patton Electronics Model # Descriptio n IM1/ A .............................. . V .24 with DB25 F IM1/ B .............................. . RS422/RS530 with DB25 F IM1/ C .
3 3 APPENDIX C PA TTON ELECTRONIC S MODEL 1092A INTERFACE PI N ASSIGNMEN T (Continued ) V .35 Interface (M/34F Female Connector ) (DCE Configuration ) Pin # Signa l B .......................... . SGND (Signal Ground ) C .......................... . RTS (Request to Send ) D .
APPENDIX D APPENDIX D PA TTON ELECTRONIC S MODEL 1092A CONTROL PORT PIN ASSIGNMEN T The 1092A control port is an 8 position connecto r, compliant wit h EIA/TIA-561 .
デバイスPatton electronic 1092Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Patton electronic 1092Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPatton electronic 1092Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Patton electronic 1092Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Patton electronic 1092Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Patton electronic 1092Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPatton electronic 1092Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Patton electronic 1092Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPatton electronic 1092Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。